Re: The Snortin' bull
2 Attachment(s)
Plug wire's in loom's.Added a boot with trim around shifter.
|
Re: The Snortin' bull
3 Attachment(s)
Mounted up new dual needle air gauges I received from bagriders. After mock up of several different and common gas tanks for these trucks I chose to modify and use a first generation Ford Mustang gas tank.Using a Stewart And Warner adapter plate for a universal 0 to 30 ohm sender for the stock guage.And modifying the original sender to be only a pickup tube for fuel.
|
Re: The Snortin' bull
1 Attachment(s)
Set up the classic instruments sender kit to fit the tank.
|
Re: The Snortin' bull
2 Attachment(s)
After a stack of different pulley combo's a match is made.A few shims on bracket's we now have alignment.Fan spacer and fan.Now a load of belt's and match them into this and a shroud. Considered going electric fans though still sticking to a plan and theme.Budget $ and use what is in the garage.
|
Re: The Snortin' bull
3 Attachment(s)
Another extended summer day in Seattle.Finished mounting adapter plate in fuel tank for S&W sender.Painted tank.Support frame work fab'd in for tank .Mounted in at the end of weekend after painting support frame for tank.
|
Re: The Snortin' bull
2 Attachment(s)
Fuel tank mounting.
|
Re: The Snortin' bull
4 Attachment(s)
Finished plumbing, Fuel line's done.Brake line's done. After a stack of v belt's got a set to match.
|
Re: The Snortin' bull
Looking good. Getting closer.
|
Re: The Snortin' bull
Thank you.Not to far from it moving on it's own,Almost to heavy to get in and out of the garage.
|
Re: The Snortin' bull
3 Attachment(s)
Plumbed in air gauge's.Routing the little line's are something to watch what the they can rub on and protect them.I know some people don't like this set up and would go for full Accuair controlled though this is a budget project and a bit old school. >> Noted that now the Accuiar vu4 has pressure on both side's of the solenoid's it is not bleeding down.This drove me crazy .There where no leak's and the truck would drop overnite. Now it stay's pumped up.
|
Re: The Snortin' bull
3 Attachment(s)
Wired in the lockup release and the dual circuit stop lamp switch and got it mounted in. This is needed for the 700r4 lockup circuit.The cardboard box is the only left over part's from the start of the project.The truck was stripped for the most part.
|
Re: The Snortin' bull
3 Attachment(s)
Had a driveshaft made this week with new yoke's installed. Gotta say Measure and measure both up and down and loaded suspension before getting these made up. Fit perfect . Fluid in steering pump now. On to the next step.
|
Re: The Snortin' bull
2 Attachment(s)
Got the hood back on.Take sometime to set up gap's and latching next. The Bull has it's nostril's back.
|
Re: The Snortin' bull
2 Attachment(s)
So this is no show truck nor resto.It is done within a budget and with a lot of collected part's from the year's past.It still need's to look ok when done. Tightened up the frt. sheet metal today.These are the cab corner upper cowl cover's gapped out fairly ok.
|
Re: The Snortin' bull
2 Attachment(s)
Set up of the speedo drive gear and driven gear housing. Here is a calculation method to set up speedo gear tooth count's.
|
Re: The Snortin' bull
Maybe I missed it, but are you using your factory idler arm? What center steering section are you using? What year power steering box too?
Thanks, Wade |
Re: The Snortin' bull
I am using a frt donor suspension and crossmember from a 1987 c-10. Idler and gear box is from it also though new. The center link is original 1960 only becuase for some bling.i used Cpp tie rod sleeve's.I put in steering box adapter plate kit from Cpp also. QUOTE=rwade;7323252]Maybe I missed it, but are you using your factory idler arm? What center steering section are you using? What year power steering box too?
Thanks, Wade[/QUOTE] |
Re: The Snortin' bull
3 Attachment(s)
Start battery in.This is the primary though a constant duty solenoid will keep the other battery charged for the compressor's.Transmission dipstick and tube in and it hide's well.Transmission cooler I am searching for a good mount location .
|
Re: The Snortin' bull
2 Attachment(s)
Put on the transmission lower cover for the flexplate and convertor.Removed the tailshaft housing of the trans to install the drive gear for speedo.
|
Re: The Snortin' bull
2 Attachment(s)
Mounted the constant duty solenoid and started wiring it. Starter wired. Transmission dipstick tube mounting tab attached to rear of block now also.
|
Re: The Snortin' bull
Nice and clean!!!!
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Gettin close.
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
2 Attachment(s)
Got a couple things done at night during week. Shock lower rear brackets ready to get tacked on. Battery cable terminal ends done. Been busy at work so not to much time at night.
|
Re: The Snortin' bull
1 Attachment(s)
finished the tailshaft of transmission .Speedo all hooked up.
|
Re: The Snortin' bull
4 Attachment(s)
The batterie's are all wired in now.Finishing up harness of truck.Got interior wired,Back lighting wired in for guage packs,Exterior lighting wired.Alternator wired.
|
Re: The Snortin' bull
2 Attachment(s)
Working on the rear lighting harness.This truck had a handful of hole's in dash and everywhere.I filled them various period style switches instead of filling them.Keepin' the theme.
|
Re: The Snortin' bull
2 Attachment(s)
Diggin in part's boxe's I had an old school fill neck. From a 30"s Studebaker. For now it'll work.Set in the wood in the bed to mock up fill neck.
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
1 Attachment(s)
Through out this project rust is in the way as it for most of us.This stuff is the fashnizz. Aerokroil none better work's like a champ.
|
Re: The Snortin' bull
2 Attachment(s)
Even though this truck will look like a road side left over little detail's like ugly windshield squirter's bugged me..Found some original style on a parting out truck in the paper.The little round head one's are now on the hood.
|
Re: The Snortin' bull
1 Attachment(s)
Turn signal lever I modded. This might mess with some folk's . Back in the fiftie's rodder's would flip the shifter to left of the column.
|
Re: The Snortin' bull
1 Attachment(s)
A license frame from the sixtie's in Seattle . The gmc in red matched the lettering on the tailgate of the truck.
|
Re: The Snortin' bull
1 Attachment(s)
The red positive battery cable stood out.Used some old school asphalt loom to blend it in under the hood.The loom is cool stuff.Using it in other area's also.
|
Re: The Snortin' bull
2 Attachment(s)
Got my seat belt's and anchor plate's from Juliano's today. Started to install. There will be belt's also for a center passenger.Sorry about the grainy pic's.
|
Re: The Snortin' bull
Looks good.
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
1 Attachment(s)
Got my gas cap and fill neck today from BAM Manufact..Look's and fit's better than my temporary set up.
|
Re: The Snortin' bull
Good progress. like that gas cap setup. Clean
|
All times are GMT -4. The time now is 09:34 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com