Re: What did you do to your truck today? Chapter II
 

Things just got serious. The tear down begins.

Pulled the cowl and driver's side front fender off. Spent a few hours trying to straighten it up and beat the wrinkles out. Not a bad start and much better than it was. Then, I painted my aluminum intake to get ready for the engine swap.

Re: What did you do to your truck today? Chapter II
 

Got the under dash lights from board member thelonerife thread TN Underdash lights. Bulbs are cheap LED's from Ebay.

Re: What did you do to your truck today? Chapter II
 

Looking good!

Re: What did you do to your truck today? Chapter II
 

Looking good!

Re: What did you do to your truck today? Chapter II
 

Thanks! Good to see a fellow :gmc2: owner in town.

Re: What did you do to your truck today? Chapter II
 

Today I got the fuel gauge working again - float had a pinhole and was full of fuel. Being Sunday with no dealership open to sell me a new float, I just fixed the old one. So far, so good - we'll see if it's still floating in a few days. Also pulled the glove box, part of the AC shroud, and the control cables to try and fix a heater problem. They lubed up pretty well, I bet they'll work great with the new levers on the way. New tires a few days back, getting the brakes dialed in this week, buttoning this thing up... the new LS swap is running awesome!

Re: What did you do to your truck today? Chapter II
 

Made more old things shiny.

Re: What did you do to your truck today? Chapter II
 

It is with no small amount of personal satisfaction that I announce (working alone no less) the reattachment of the canister hardlines! I had to fiddle with it a bit but I kept both calm and patient. At one point I called my neighbor and left a message requesting his help, then BINGO I got it! I called him back telling him not to worry but here he came anyway. I love my neighbors!

Tomorrow I am going to start making the actual fuel lines (supply lines). *Happy dance. :) :) :)

Re: What did you do to your truck today? Chapter II
 

I got my box, rear fenders, steps, tailgate and tail lights on this weekend.

Re: What did you do to your truck today? Chapter II
 

I got the bumper on and painted my rad support. Ready to mount the front fenders and grill tomorrow.

Re: What did you do to your truck today? Chapter II
 

Reinstalled cowl with ss mesh to keep out leaves. Also made some progress on the AC install.

Re: What did you do to your truck today? Chapter II
 

Allchevy58 - Those fender wells look sweet. Can't wait to replace my rusted out ones.

I also used some rattle can that matched awesome, waiting for more to come in the mail to clean up engine bay.

Re: What did you do to your truck today? Chapter II
 

Love to cowl screen. I think I would have painted it to match the body though.

Re: What did you do to your truck today? Chapter II
 

I'm curious to know what brand of adult beverage that is on your stool? Bud? Lol

Re: What did you do to your truck today? Chapter II
 

I had a couple molson canadian beers after the work was done. That's the best time. It's nice to take a break, sit back and look at all the work that has been done. As I tell the wife, we are not just drinking beer in the shop. There is a lot of R&D going on planning the next step. You don't want to screw something up and have to do it over.

Re: What did you do to your truck today? Chapter II
 

"Reflection time" is a necessity! Cheers! Lol

Re: What did you do to your truck today? Chapter II
 

It's about time I got busy and did a much needed brake job on my 70 GMC and decided to swap the cab on my 72 1 ton dump truck. Have the week off and the brake job didn't go so well. Ended up using 8 can of brake cleaner on the 4 drum brakes. Wow, what a mess. two of the wheel cylinders have been leaking for some time. That coupled with the rust from mostly just sitting the last two years. Also found a kinked brake line on the rear. Now I know why I had hardly any breaks. Need help. I completed replacing three of the four wheels cylinders and I'm down to the last one on the front. I can't get the last wheel cylinder off. I can't get the big retaining bolt out to get the wheel cylinder off! The other side came off after a couple hit with a 2 lb. hammer on the 1 1/8 wrench. No go on the other side. The bolt is starting to round off. Help! Am I going to have to heat it up to get it to break free? I don't have a torch. Any suggestions? Since I have decided to go ahead and replace all the metal break lines I 'm at a stopping point on the GMC until I order all new lines. So I started on the cab swap. I have a 72 C 10 truck I'm going to use for the cab and front clip. Here is what I got done to day. Hope to get the cab off tomorrow.

Re: What did you do to your truck today? Chapter II
 

The rust is really bad on the cab and front clip. The drivers door hinges are shot. the truck had a fender replaced some time and they tack welded it to the cab along with the rockers bondoed to the bottom of the front fenders.

Re: What did you do to your truck today? Chapter II
 

I got the front fenders on and adjust pretty close. I then got the grill, one chrome strip and the bumper on.

Re: What did you do to your truck today? Chapter II
 

Sounds like you should use a 6 point impact socket .

Re: What did you do to your truck today? Chapter II
 

Hahahahaha! That's one of the things that makes these trucks great. The differences in taste when building design mods.

FWIW, I absolutely LOVE the looks of the cowl screen. Exactly the way it was done.

That's what makes horse racing, too.

Re: What did you do to your truck today? Chapter II
 

Did you make that cowl screen or did you purchase it from a vendor? LMC, Brothers, etc.... IMO, I like the way you left it in the ss. Don't paint it, it has great contrast that way. And heck its stainless, you don't have to paint it, it wont rust. :metal:

Re: What did you do to your truck today? Chapter II
 

Its actually starting to look like something! Its amazing to find out how big of a difference it makes to start from the FRAME!! I originally tried to line up fenders with one original fender still on the truck... Ashamed to say I actually had the 6' pry bar on it! Just for the fenders! Then I finally gave in and listened to pops and started from frame leaving all bolts hand tight. Wow what a difference.I've only "hung" them for now. I know the real test will be my patience when I have to button it all up and set my body lines. At least I have routing paths for my electrical now,total rewire. Any tips are greatly appreciated. Won't be long now til I'm back on the road again terrorizing the neighborhood with those "super" 40-flowmasters. I'm sure they've thought I moved by now,considering its been almost ten years that it's been off the streets...

Re: What did you do to your truck today? Chapter II
 

Tried that but it won't break free. Thanks

Re: What did you do to your truck today? Chapter II
 

Heat is your friend,,,, Map gas can be bought at most parts stores or hardware stores.
Good luck