![]() |
Re: PO has me PO'd
Quote:
Quote:
Quote:
Interior looks sweet AJ, I got the same shifter, so I guess my interior will look as good as yours;) |
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
I'm going to pull mine apart, check everything out and replace as needed. |
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
Actually I don't expect to replace much. My engine has only about 15,000 miles on the rebuild. The PO gave me a boat load of paperwork/receipts all for the engine work that had been done. We'll see though. With my luck, it will need a total overhaul. :sexy: |
Re: PO has me PO'd
That is one tough looking crossmember...
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
...been a couple weeks, what's the latest with your stuff?
|
Re: PO has me PO'd
Quote:
atleast that's the current slogan... wait till another 4 star needs an OER bullett comment and it will change, again... along with our uniforms, again |
Re: PO has me PO'd
Quote:
After that crossmember, I've just bin staring.... Putting the front of the motor back together, permanently! Gotta figure out a PVC system, Ive got the Offy breather mounted, just have to buy a valve and plumb it into the air cleaner. Work on the exhaust to mount up everything, then it's on to carb, distributor, and radiator Then.... Vroooom, Vrooooom:lol: |
Re: PO has me PO'd
Quote:
Looking forward to the Vroooom Vroooom! :lol: |
Re: PO has me PO'd
Here is my current problem, I am done mockup and into final assembly. I want to bring the heater outlet hose into this location, but w/o a cobbled up looking mess. Soooo, I plan to make a W/P outlet tube longer and be able to thread into it a 45 degree 1/2"X5/8" barbed fitting. That alone could be a problem since that is not a standard fitting
http://i89.photobucket.com/albums/k2...replace627.jpg |
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
You know, I've never checked to see if the threads on a water pump are pipe threads or parallel. I just assumed they were NPT or it would be very hard to keep them from leaking. Hmmm. |
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
Ok Jim, what brand and model do you have and I will check it out...I'm on it! |
Re: PO has me PO'd
Quote:
I think its a Proforma, but I'll check Here's a pic of the outlet that needs to be longer so I can drill and tap a 1/2" NPT. The outlet from the water pump is 1" NPT http://i89.photobucket.com/albums/k2...replace631.jpg |
Re: PO has me PO'd
Thanks Tim for the answer...Alum. 1"NPTX2 1/2"nipple(don't go there) with a full coupling. Now I can machine a flat on the factory Proform water pump outlet and drill and tap a 1/2" NPT female to put my hose barb in...again, don't go there, lol
Down the road I will modify this using thin wall pipe and the high pressure 1/2 coupling to eliminate the ugly threads that show Parts were here from Mcmaster-Carr in 1 day, the greatest hardware store you ever want to visit Pics?...OK http://i89.photobucket.com/albums/k2...replace634.jpg http://i89.photobucket.com/albums/k2...replace636.jpg http://i89.photobucket.com/albums/k2...replace637.jpg |
Re: PO has me PO'd
Quote:
Where exactly are you going to machine a flat and drill and tap for the hose barb? Just curious. |
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
http://i89.photobucket.com/albums/k2...replace638.jpg |
All times are GMT -4. The time now is 07:51 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com