![]() |
Re: What did you do to your truck today?
I worked on the bed floor a little more & I'm much closer to completing the fuel fill line. See my build thread for details....
|
Re: What did you do to your truck today?
Quote:
|
Re: What did you do to your truck today?
Welcome to the forums ss69bowtie. Post some pictures of your truck, so we can enjoy it. You will find a wealth of knowledge on this site, so don't hesitate to ask. Take care and good luck with your project.
|
Re: What did you do to your truck today?
All I seem to do lately is get to work to many hours, drive my truck everyday to and from.....:waah:
|
Re: What did you do to your truck today?
I built all my brackets for my 4 link and bags at work on the CNC, I love those things.
|
Re: What did you do to your truck today?
took the truck out to get the news papre and pick up some milk down at the store...it aint much but is better than nothing....Oh did I mention that its -9* and the frost heaves are getting so high in the midle of the travel lane that riding low is alomost out of the question
|
Re: What did you do to your truck today?
Got my tail lights put back together. Primered the tail gate trunions. Took the dog for a ride.
|
Re: What did you do to your truck today?
Swaped out the tail gate on the stepside, drove the fleetside ( no rain!!)
plan on toping off the trany |
Re: What did you do to your truck today?
1 Attachment(s)
went to the train station
|
Re: What did you do to your truck today?
Started putting my Hurst shifter in. Had to get my wife to hold it from the top while I bolted something on the bottom. After several sighs and a few how much longers, I said...hey...it's not like I asked you to polish my knob, just hang onto it for a minute! She found a lot less humor in it than I!:lol::lol:
|
Re: What did you do to your truck today?
That's funny Bob, my wife would have just droped it.
|
Re: What did you do to your truck today?
I worked on my fuel fill line again after getting off work this afternoon. This one task is taking entirely too long for my patience. I'm struggling to get what I feel is enough 'slope' so that all fuel runs into the tank.
|
Re: What did you do to your truck today?
3 Attachment(s)
Im taking steps backward and removed the rear suspension! Damn the rusted bolts and busted knuckles so I can figure where my notch is going. Heres how it sits without notch on the frame. I only smacked the same thumb twice...
|
Re: What did you do to your truck today?
well i started cutting out my rockers for rust repair. im excited, this is the first time ive posted in this thread. i hope the weather is nice this week and i can get more done.
|
Re: What did you do to your truck today?
I pulled driveshaft/brake lines/suspension loose/CUT the rear axle loose from my frame (U-bolt nuts were froze solid) on my way to a front disc/5 lugs all around conversion. This project has been too slow due to cold weather... Hoping to start pulling the front end apart tomorrow! (66 Chevy 3/4 ton frame for my 64 GMC build)
|
Re: What did you do to your truck today?
I unloaded my new 8.8 rear axle out of my jeep today for the '64. I think I might go into the garage right now and start tinkering with it, maybe mount my fuel pump too.
|
Re: What did you do to your truck today?
Took the idiot light instrument panel out in preparation to put a gauge instrument panel in. Also, took the heater control and cables out, replaced the broken heater control levers, and lubed up the control cables. Will be putting this all back in today. It's supposed to get to about 24 degrees outside today, so it won't be too bad. The sun will heat up the cab a bit and make it bearable, too much snow/ice yet to move the truck to the garage.
|
Re: What did you do to your truck today?
I spent the last few days stripping the paint off a hood I just bought. Looks like my old hood will take less work than the new one. $100 wasted.
Chop |
Re: What did you do to your truck today?
:lol: :lol: :lol: :lol: :lol: :lol:
Quote:
|
Re: What did you do to your truck today?
3 Attachment(s)
Another update for the continuing saga of installing a Camaro dash in my '65 C10 SWB SS: Test fit a "Covans" aftermarket dash panel. I was amazed at how well this fit with only some slight trimming. This will allow me to use stock dash mount style gauges.
Now I need to drop some serious "coin" for gauges. Also attached my floor handbrake cables up to the rear brakes. I was pleased to find that the hand brake works great. Brakes get good and tight with still some extra ratchet pull yet to go. |
Re: What did you do to your truck today?
1 Attachment(s)
bought it and hauled home 66 1/2 ton 2wd
|
Re: What did you do to your truck today?
|
Re: What did you do to your truck today?
2 Attachment(s)
I tured the crappy green firewall, black. I am going to try and get the engine and tranny stabbed in this weekend.
|
Re: What did you do to your truck today?
2 Attachment(s)
got engine swaped and front wrap mostly re installed
|
Re: What did you do to your truck today?
Quote:
|
All times are GMT -4. The time now is 04:22 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright 1997-2025 67-72chevytrucks.com