Re: 68 aka "Chained in Porterbuilt Prison"
I may have missed it but can u give more details on the front brakes?
|
Re: 68 aka "Chained in Porterbuilt Prison"
Looks great Jim...Jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
|
Re: 68 aka "Chained in Porterbuilt Prison"
Looks like a work of art. Too nice to cover with a body....
|
Re: 68 aka "Chained in Porterbuilt Prison"
The more parts you put on the better and better it looks. Keep it up.
|
Re: 68 aka "Chained in Porterbuilt Prison"
Nice looks great
|
Re: 68 aka "Chained in Porterbuilt Prison"
Your chassis looks super nice! Great work!
|
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
|
Re: 68 aka "Chained in Porterbuilt Prison"
5 Attachment(s)
Got the stainless brake lines installed...in front was able to install "thru the frame" ...line works great in any position of spindle and whether slammed or in full up mode...(and it's not that close to shock as it looks..bends nicely on turns)...rears may surprise some but works like front ....any position of rear end they clear..still waiting on mastercool flaring tool for hardlines....and last if you haven't seen this 7 conducter wire for rear section here it is....has 6 14 gauge wires and 1 12 gauge wire (fuel pump)...No harness wrap needed...more on this in couple of days...jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
Looks great, what length brake lines did you go with front and rear.
|
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
|
Re: 68 aka "Chained in Porterbuilt Prison"
Brake lines look great. Is your rear wiring for a trailer application? That's what I usually get too.
|
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
|
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
|
Re: 68 aka "Chained in Porterbuilt Prison"
I wish I had known about that wire. That is slick, I just ran the original wire and a seperate wires for fuel pump and sender. Thanks for sharing
|
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
http://www.ebay.com/itm/7-Conductor-...50ed13&vxp=mtr Did you ground one side of that sender at rear?? I've got to look up the wiring diagram for that...been to long!!.....jim |
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
|
Re: 68 aka "Chained in Porterbuilt Prison"
4 Attachment(s)
Few more pics after today's work...wires pulled thru frame and ready to terminate at batteries..that ugly (right now at least) 1" tube will carry crossover battery lead and wires to pump and sending unit will grommet out of tube (no holes done for that yet)....anyone guess what grommet that is bringing up positive cables??.........pcv valve cover grommet...works perfect...........strung cables down frame rail...pass side is straight to starter lug....dr. side powers powers rest of truck....black cable is 7 conductor for rear lights..pump...sending unit...................jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
2 Attachment(s)
This is how i hid wires in notch......
|
Re: 68 aka "Chained in Porterbuilt Prison"
Looking good!
|
Re: 68 aka "Chained in Porterbuilt Prison"
Jim, that looks great...Jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
Frame looks great BTW. |
Re: 68 aka "Chained in Porterbuilt Prison"
5 Attachment(s)
Finally got rear wired....here's a few pics...loose wires at back are for lights...#6 red and black by pass. battery will loop over behind marker light to jump terminals....open marker light ..u can charge or jump start.....well back to painting engine and trans and wiring accuair and plumbing rear....oh boy!!!!!:uhmk:
|
Re: 68 aka "Chained in Porterbuilt Prison"
Lookin good sir!
|
Re: 68 aka "Chained in Porterbuilt Prison"
That looks sweeeeeet...Jim
|
All times are GMT -4. The time now is 08:32 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com