The 1947 - Present Chevrolet & GMC Truck Message Board Network

Got some of the wood in today. Took me 4 1/2 hours to get these six pieces in. A lot of adjusting and moving around. The hardest part was trying to hold up the cross braces and get a nut on the bolt. The bed also spread apart about 1/2 an inch so I need to figure out how to pull the inner panels together while holding the bolt in the hole and the cross brace up while putting a nut and washers on the bolt that is in the deep pocket of the brace. I wish I had a conjoined twin about now. :lol:

Hey Don use a deep socket put 2 nuts down in the socket a 3rd one will stick out a hair or so depending on the type of socket you use. You can also use a short extension on the socket..Vernski:metal:

mustangchef

09-15-2013 03:40 AM

Re: What did you do to your truck today?

Took Out the Lightning..https://www.youtube.com/watch?v=cvQkwykdyes

firemanjimtfd

09-15-2013 06:50 AM

Re: What did you do to your truck today?

Quote:

Originally Posted by gixxer711 (Post 6269017)

Taken longer than a day, but pretty much finished up. A little before and after.

http://i347.photobucket.com/albums/p...ps1fd50822.jpg

Looks much better . I would like those valve covers and breather on my 66

donthekawguy

09-15-2013 07:46 AM

Re: What did you do to your truck today?

Quote:

Originally Posted by Vernski (Post 6269755)

Hey Don use a deep socket put 2 nuts down in the socket a 3rd one will stick out a hair or so depending on the type of socket you use. You can also use a short extension on the socket..Vernski:metal:

Thanks Vern. I got sore fingers from trying to reach up in there! I saw you crossing the bridge in your truck yesterday. I waved but you didn't see me.

endlessearth

09-15-2013 04:39 PM

Re: What did you do to your truck today?

Today I used my truck to teach my 12-year old son how to drive standard and introduced him to the hobby.

http://img30.imageshack.us/img30/2512/lemq.jpg

http://www.youtube.com/watch?v=JA6Hd2t30tY

*Legal disclosure: We stayed on private property the whole time. No animals were harmed in the making of the short film below because all the dinosaurs that went out the exhaust were already dead on the way into the carb.

Ta2Don

09-15-2013 07:23 PM

Re: What did you do to your truck today?

Quote:

Originally Posted by endlessearth (Post 6270480)

Today I used my truck to teach my 12-year old son how to drive standard and introduced him to the hobby.

http://img30.imageshack.us/img30/2512/lemq.jpg

http://www.youtube.com/watch?v=JA6Hd2t30tY

*Legal disclosure: We stayed on private property the whole time. No animals were harmed in the making of the short film below because all the dinosaurs that went out the exhaust were already dead on the way into the carb.

Awesome... My Daddy taught me to drive his, at that moment in time, new 76 LWB Chevy straight 6, 3 on the tree... no P/S and no P/B....
as for the Legal Disclosure...:metal:

ratrod11

09-15-2013 09:28 PM

Re: What did you do to your truck today?

3 Attachment(s)

Finally... got to spend some quality time on the truck. Got the cab on the ground at last! I just have to remove the motor and I will post a 1962 factory 4x4 chassis for sale in parts!:metal:

Chevy Fleetside

09-15-2013 09:58 PM

Re: What did you do to your truck today?

2 Attachment(s)

today I drove up the shop and grabbed the carb off the other truck and put it on my 65. The one I had on there i got at 1/2 price day at pick and pull, it seemed to be a rebuilt carb since it was clean and had a tag on it. Well it was giving me nothhing but trouble so I swapped it out to the one I knew was good and it runs good. Just need to do alot of small adjustments to it. Well after that I drove it around the block.. oh yeah more then once.. :metal::lol: Looks like with the BB in there I have more rake now.. I think I like it as a Fleetside instead. The pic of it being a stepper is with a SB in it. I didn't change the stance at all.

niterider65

09-15-2013 10:47 PM

Re: What did you do to your truck today?

5 Attachment(s)

spent some time in shop and dang guess H E double tooth pick must have froze over . i got 2 things done . primed the frame and painted it .I must be sick . dang what next put it back to gether :lol::metal::chevy:

DexterDog

09-15-2013 11:45 PM

Re: What did you do to your truck today?

Damn double post.

DexterDog

09-15-2013 11:52 PM

Re: What did you do to your truck today?

Today, I flipped my whites out and repainted the wheels. Best $10 spent so far.

BEFORE
http://i21.photobucket.com/albums/b2...psbf9a6707.jpg

AFTER
http://i21.photobucket.com/albums/b2...ps0344e6c0.jpg[/URL]

gmcdeadhead

09-17-2013 12:55 PM

Re: What did you do to your truck today?

finished up the power steering and front end conversion. 100% better stopping and steering. capt fabs brackets were the best. [IMG]http://i792.photobucket.com/albums/y...pse67664bf.jpg[/IMG]

Daking19

09-17-2013 01:08 PM

Re: What did you do to your truck today?

That is a good concept. I sent my grill out to be powder coated today

donthekawguy

09-19-2013 01:43 AM

Re: What did you do to your truck today?

I went out to put the center wood pieces in my bed today only to find out that they were too wide. Grrrrrrrr I cut them to the width listed on GMC Pauls website. I ripped them down and put on more urethane. Then the rain started so I will have to wait till tomorrow to put it together. My son is coming to help so it should go pretty fast. My plan is to get the wood in loosely tip it back up on end, make sure it's square then tighten it all down while my son feeds the bolts through from the other side. I'm still going to have the bolts that hold the bed to the frame hidden. I want to be driving it by tomorrow night!

robber grin

09-19-2013 07:58 AM

Re: What did you do to your truck today?

Jim - motor looks bad-@$$!

Quote:

Originally Posted by donthekawguy (Post 6276140)

I too used those dimensions and I was wondering if the chatter I had heard from time to time about final fit had any merit - now I am concerned it did.

Going to do a dry-run with un-finished boards and go from there...

I'm still doing body-work on my much abused cab roof panel.

Ray and I went to welding supply yesterday since he needed a chipping hammer for tech-ed and filled all the bottles, got the hammer, then putted over to pick up some white single-stage enamel and odds and ends at the paint supply. Costs are getting sick...

dexter - I'm LOVIN your truck! Thanks for posting pics. Fun times for sure.

back to the truck -
rg & ray~ray

Woogeroo

09-19-2013 09:39 AM

Re: What did you do to your truck today?

Yesterday w/ my '65 c10 :

changed the oil/filter and lubed up everything. changed the air filter out, checked all the fluids and things while I was dirty.

major adventure : old grease gun started leaking the grease out the end, except it was in a liquid-y mess! Never had that issue before, I'm suspecting it's some synthetic-y lube, it's a reddish color... what a mess!

old trucks are fun!

-W

robber grin

09-20-2013 08:05 AM

Re: What did you do to your truck today?

Spread Icing and block-sand.... repeat... spread more Icing and block again... and again... and...

Teaching my son (+ myself) patience - 90% preparation right.
rg

T Smith

09-20-2013 08:26 AM

Re: What did you do to your truck today?

Put my headers on, headed to the muffler shop in the morning. Originally planned to just hook up the existing pipes but think I'm going to have him run all new stuff all the way out.

donthekawguy

09-20-2013 02:05 PM

Re: What did you do to your truck today?

Quote:

Originally Posted by robber grin (Post 6276290)

Jim - motor looks bad-@$$!

I too used those dimensions and I was wondering if the chatter I had heard from time to time about final fit had any merit - now I am concerned it did.

Going to do a dry-run with un-finished boards and go from there...

I'm still doing body-work on my much abused cab roof panel.

Ray and I went to welding supply yesterday since he needed a chipping hammer for tech-ed and filled all the bottles, got the hammer, then putted over to pick up some white single-stage enamel and odds and ends at the paint supply. Costs are getting sick...

dexter - I'm LOVIN your truck! Thanks for posting pics. Fun times for sure.

back to the truck -
rg & ray~ray

If I was going to do it again I would cut the boards to length, rip them to width, put them in place with the strips on and a few bolts through the holes and make sure the widths were correct. Then I would mark all of the lengths with a penic for the dado cuts. Another problem I'm having is the dado's are too far in so the strips don't fit right. I got most of them to fit right but a couple are noticeable. The 3 rd board from the right is the worst one. I might have to redo it.

mud.man.rj

09-20-2013 05:08 PM

Re: What did you do to your truck today?

Have never installed a wood bed floor, sounds tricky for sure, like need a lot of patience.

donthekawguy

09-20-2013 06:16 PM

Re: What did you do to your truck today?

Quote:

Originally Posted by mud.man.rj (Post 6278405)

Have never installed a wood bed floor, sounds tricky for sure, like need a lot of patience.

It's really time consuming but not real bad. I'm stuck where I'm at now due to needing help and everyone is at work. lol

mud.man.rj

09-20-2013 06:32 PM

Re: What did you do to your truck today?

Lucky for me 6 out of 7 67-72 trucks I had were the metal floor and the one wood floor was in good shape, lucky.

jayoldschool

09-20-2013 09:52 PM

Re: What did you do to your truck today?

Quote:

Originally Posted by donthekawguy (Post 6276140)

I went out to put the center wood pieces in my bed today only to find out that they were too wide.

Step or fleet? I used their Fleetside dimensions, and they were right on.

donthekawguy

09-20-2013 10:30 PM

Re: What did you do to your truck today?

Quote:

Originally Posted by jayoldschool (Post 6278732)

Step or fleet? I used their Fleetside dimensions, and they were right on.

I have a fleet. I'm sure I used the right ones but my bed is all messed up so who knows. :lol: I put it back on yesterday and two of the holes didn't even come close to lining up even though it's straight and square on the frame. I just drilled out new holes and said to hell with it. :metal:

jayoldschool

09-20-2013 11:17 PM

Re: What did you do to your truck today?

Here's how mine turned out:

http://i40.photobucket.com/albums/e2...psabea46c3.jpg

All times are GMT -4. The time now is 12:09 AM.

Page 341 of 360