Re: What did you do to your truck today part IV
 

Thank you! I'm very happy with them so far

Re: What did you do to your truck today part IV
 

What wiper delay kit did you use?

Re: What did you do to your truck today part IV
 

Cab interior in primer!Attachment 2138743

Attachment 2138744

Re: What did you do to your truck today part IV
 

Blasted my wheels and painted them. Got new tires.

Re: What did you do to your truck today part IV
 

Installed KYB Gas-A-Justs to try to keep the top of my tires off the fender well. They help some over the standard Monroes, but still touch when in tight corners.

Re: What did you do to your truck today part IV
 

Gettin ready to pull the lowered rear leafs and switch over to a nolimit 4 bar.

Re: What did you do to your truck today part IV
 

Have a converted short bed with an LS and a th 400. Had terrible vibration at 70 mph. Shimmed rear 2 degrees down and trans 1 degree up per spicer calculator. Problem solved

Re: What did you do to your truck today part IV
 

It’s hard when your truck looks so good with that stance to change it at all

Re: What did you do to your truck today part IV
 

So true. I have 4" drop springs I can't use because my Monroes couldn't handle them. These KYBs raise the front slightly, unfortunately, and there's still the occasional rub. Might work if I had shorter front wheels. :waah:

Re: What did you do to your truck today part IV
 

I put the doors, fenders, cowl, & cowl extensions back on the truck for the last time until final prep and paint. I still have to work on gap alignments on the cowl extensions, cowl, and hood, and I also need to block out the hood.

Re: What did you do to your truck today part IV
 

Vary exciting looks good.

Re: What did you do to your truck today part IV
 

Pdx what is your plan for color?

Re: What did you do to your truck today part IV
 

Greased all of the front end zerk fittings...didn't realize there were so many! Hopefully that will take care of my squeaking front end.

Re: What did you do to your truck today part IV
 

Starting on replacing the bed floor. I have a '72 parts truck with a steel floor bed. I am going to cut down the bed floor and adapt it to the stepside . It will be reversable. I will do a wood floor when I build the truck into a hotrod. I just want it usable now on the cheap. I have the parts and the skill and the time just no money for the replacement bed parts right now.

Re: What did you do to your truck today part IV
 

This looks great, can’t wait till I’m near this state!

Re: What did you do to your truck today part IV
 

A few more.

Re: What did you do to your truck today part IV
 

Stripped the paint off the passenger door this summer, just getting around to reskinning inner and outter skins and treating inner cavity with sealer…Attachment 2147278

Attachment 2147279

Attachment 2147285

Re: What did you do to your truck today part IV
 

Nice. :)

Re: What did you do to your truck today part IV
 

Finishing up my 4 link conversion.

Re: What did you do to your truck today part IV
 

We had a Christmas cruise so I decked out the truck

Re: What did you do to your truck today part IV
 

I am going with seamist jade with a white roof. The paint is a 2 year only color for 62-63. Very rare but I really like it.

I've been working for a week on aligning all of the panels on Sanity. I want to make sure it all lines up reasonably well after all the body work done.
I set out the bed wood and strips to get ready for installing to measure and mark the bolt holes that need to be drilled.

Re: What did you do to your truck today part IV
 

Finally finished my driver side exhaust over the rear end, under the panhard out to the tip, with the weight restrictions and short shop time after hip surgery, everything takes forever……

Re: What did you do to your truck today part IV
 

Nice! Is that all tig welded?

Re: What did you do to your truck today part IV
 

Yes, tig weld. On finishing, mig tacked during mock up…for myself it’s easier to give it a quick tack. I make all my exhaust systems to be able to be taken completely off without cutting anything, the vband clamps allow that.

Re: What did you do to your truck today part IV
 

Very nicely done.

Re: What did you do to your truck today part IV
 

Thank you, appreciate your kind words….

Re: What did you do to your truck today part IV
 

Finally finished both sides on my exhaust….

Re: What did you do to your truck today part IV
 

^^^awesome^^^ I wouldn't mind seeing a little more of that.

Re: What did you do to your truck today part IV
 

👍 agreed

Re: What did you do to your truck today part IV
 

Thank you, its tedious and time consuming, but I like to build my own, lots of these pieces were left over from my last 2 cars…

Re: What did you do to your truck today part IV
 

MT65 meticulous job on your exhaust! Looks great. Don't think that I have seen one tucked so close in behind the tire before.

Re: What did you do to your truck today part IV
 

MT65 meticulous job on your exhaust! Looks great. Don't think that I have seen one tucked so close in behind the tire before.

Re: What did you do to your truck today part IV
 

Thank you for the nice words, its got just under an inch on clearance, takes more speed than this truck will do to make the tire grow that much, at least I hope so🤔🤔🤔

Re: What did you do to your truck today part IV
 

Had to run to Home Depot for a fitting last night. When I came back out to the truck, the sunset looked great, so I snapped a few pics with my iPhone. Wish I would've had a real camera and been in a better location than HD's parking lot, but for a total impromptu shoot, I think these turned out well.

Re: What did you do to your truck today part IV
 

Finished mounting my rear sway bar, a front bar from an early 70’s Camaro should be fine, may have to fine tune end links when its on its wheels…

Re: What did you do to your truck today part IV
 

Finished mounting my rear sway bar, a front bar from an early 70’s Camaro should be fine, may have to fine tune end links when its on its wheels…

Re: What did you do to your truck today part IV
 

Finally resting on its own , maybe a little fine tuning on stance, 5” ground clearance as it sits…

Re: What did you do to your truck today part IV
 

Started working on stuff and ended up pulling the engine. I over did it as usual. :)

Re: What did you do to your truck today part IV
 

Started painting my new spindles to replace the one that broke.

Re: What did you do to your truck today part IV
 

I finished replacing the bed wood and raptor lined the inside of the bed. I got it finished and mounted back on the frame.