![]() |
Re: 68 S/C update.....
I can snap a few later today and get them to you. There is plenty of room though. Do you know off the top of your head what the hose on top of the tranny goes to? I thought it was just a vent, but it has a "T" fitting on it, like it had a hose going somewhere.
Posted via Mobile Device |
Re: 68 S/C update.....
I'm pretty sure it's just a vent.
|
Re: 68 S/C update.....
4 Attachment(s)
Pictures as requested. Sorry for the poor quality, camera phone and its hard to get in there really close. You can see the vent thing I'm talking about. I would say there is about 2" of space, maybe even a little more. However I still have to make sure I'm leveled out at the right driveline angle. I used the spacers that were on the th400 mount, but the engine still seams to dip down, and the tranny pan doesn't appear to be level. I need to get out my angle measurer and check the angle.
|
Re: 68 S/C update.....
Quote:
|
Re: 68 S/C update.....
Very nice build, sat down and read through it all today. What kind of fuel mileage do you think you'll be getting with the 6.2 combo?
|
Re: 68 S/C update.....
Dammit,
You are gonna screw up my plans for a Florida visit. :lol: Quit getting so much done. John |
Re: 68 S/C update.....
Quote:
Quote:
|
Re: 68 S/C update.....
thats some cool vids !!!!
|
Re: 68 S/C update.....
Quote:
|
Re: 68 S/C update.....
And here is the why I want to put an L99+6L80 in my Chevrolet Veraneio. First because the L99 is the only V-8 engine avaiable around here, and since playboys are starting to destroy Camaros SS maybe I could find one. But the main reason is that even stock I will get 3 times the power, and something something lower than 2 times the torque that I have with my L6 261 (first gen stovebolt). And everyting with higher kilometrages (milleages) per liter (galon). But in my case I want the AFM, VVT, etc...
|
Re: 68 S/C update.....
Quote:
I will have more shop time this summer, although I may have to find a side job for a while. Still up for a Florida trip tho! John |
Re: 68 S/C update.....
Quote:
|
Re: 68 S/C update.....
Quote:
Quote:
Quote:
Quote:
Quote:
|
Re: 68 S/C update.....
5 Attachment(s)
Well I had to pull the oil pan in order remove the oil pump in order to install the LS2 timing chain dampner in order to change the cam in order to delete the VVT.....seems like this project just continues to snowball down hil....LOL. Oh well, got that done now, I think....finally....I can start putting it back together for good, :).
|
Re: 68 S/C update.....
Man oh man that's certainly out of my knowledgable reach for those kinda of swaps. Kudos to you on tackling this endeavor of a motor I'm sure shell be perfect for ya when wrapped up.
Posted via Mobile Device |
Re: 68 S/C update.....
Looking great this far...Cant wait to see the video and then send you sylvester for it's ls6 swap :devil:
|
Re: 68 S/C update.....
2 Attachment(s)
Quote:
Quote:
*** Well it's starting to look like a motor again (PICS!). My buddy Joe and I installed the oil pan, front timing cover and the bolted the heads back on. I still need to recheck the torque on the head bolts and then I'll put in the new pushrods and the rocker arms. When I'm done with the that, I think I going to do a test fit of the engine/tranny. I'm tempted to try it without installing the high hump, but I'm 95% sure it won't fit..... |
Re: 68 S/C update.....
Looking good man.
Posted via Mobile Device |
Re: 68 S/C update.....
5 Attachment(s)
Quote:
Ernie came over yesterday and between the 2 of us (Ernie did most of the work, :lol:), we got the high hump installed. After finishing that up, we put the motor in for a test fit. Well almost, the 2013 Camaro pan isn't going to work, :(. I thought it would be close, but we confirmed it wouldn't. Two steps forward and one back...:waah:. I ordered a 2007 Cadillac CTSV pan last night and it should be here early next week. It's the same one I have on the suburban and should fix the problem. I also think I have the accessory brackets figured out. I ordered a set of the Holley LS brackets. Hopefully they will work for my truck and Jakes 68....fingers crossed! Picture time! |
Re: 68 S/C update.....
It's not often that someone asks you to cut a hole in a pristine '68 C10 floor... you just have to say yes when it happens! :lol:
|
Re: 68 S/C update.....
2 Attachment(s)
Quote:
|
Re: 68 S/C update.....
Oh yes my friend!! Love it!
|
Re: 68 S/C update.....
Coming along nicely. Yes, we did just do that...luckily, the new cab was a factory high hump
Posted via Mobile Device |
Re: 68 S/C update.....
Posted via Mobile Device
Sure wished I lived closer so I could be a part of cool things like this.....:smoke: Lol Posted via Mobile Device |
Re: 68 S/C update.....
Motor looks great in there Rob, your making me wish I had and LS in mine instead of the BBC.
Posted via Mobile Device |
All times are GMT -4. The time now is 01:08 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com