|
Re: "Project Orangepeel" 52 A.D
Nice details fitting that in too with the lowered section in the middle and the opening for the radiator cap. And it could be a pinstriping surface possibly?
|
Re: "Project Orangepeel" 52 A.D
Thank's Doug,yes possible
|
Re: "Project Orangepeel" 52 A.D
5 Attachment(s)
Pic 1. All tacked in.
Pic 2. I thought it would a cool look to match the contours and shape of the stock pan. Pic 3. all welded up. Pic 4-5. All smoothed and metal finished. If you notice I also made some side pieces that wrap around to finish it off. |
Re: "Project Orangepeel" 52 A.D
Nice job son...Dad
|
Re: "Project Orangepeel" 52 A.D
Nice work! That came out very clean. You Chevy guys have it tough sometimes!
|
Re: "Project Orangepeel" 52 A.D
Very nicely done .....as always
|
Re: "Project Orangepeel" 52 A.D
Looks neat!
I’m with Doug, great place for some pinstriping! |
Re: "Project Orangepeel" 52 A.D
Wow, Thank's Guys!!
|
Re: "Project Orangepeel" 52 A.D
5 Attachment(s)
Pne last thing I did before it came apart.
Pic 1. This was my idea for the mount for my hood prop rods. Pic 2. I used a rivnut inside the mount, and a steel collar for a shoulder bolt to go through. This way the bolt tightensall the way down and collar still moves free. Pic 3. These are hardline hold downs from notch head. Pic. 4. Rod snaps in place nice and easy. Pic. 5. Rods stay tight to the inner fender. |
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
And props in action!
Mark |
Re: "Project Orangepeel" 52 A.D
Very nice.
|
Re: "Project Orangepeel" 52 A.D
Very cool!
|
Re: "Project Orangepeel" 52 A.D
Good idea to have 2 prop rods!
|
Re: "Project Orangepeel" 52 A.D
When I use POR 15 I stir put lid on and punch a hole in the lid and put a sheet metal screw in. Then when I use next time I have a rod I put in the hole with a 90 on it and put it in the drill and mix it up never have to take the lid off again.
|
Re: "Project Orangepeel" 52 A.D
8man,A.D. and low ad thanks guys
oldstrk thanks for the tip, And welcome to the site! Mark |
Re: "Project Orangepeel" 52 A.D
Very nice!!
|
Re: "Project Orangepeel" 52 A.D
nice skills, you got room for fingers around the rad cap? prolly, just looks tight there in the pics.
|
Re: "Project Orangepeel" 52 A.D
Thanks Kees
dsraven...yes enough room to get cap off ;) Mark |
Re: "Project Orangepeel" 52 A.D
looking good!
|
Re: "Project Orangepeel" 52 A.D
looks like a great mod, I cant seem to get my springs to lift evenly, the drivers side of the hood always hits the cowl before lifting. do you have that problem?
|
Re: "Project Orangepeel" 52 A.D
Thank you,Thank you!
Joe, My springs were so rusted and hard to close I just removed them to make it easier. Dad (Oldman3) did the same on his truck because it would bow the ends out when shut. Mark. |
Re: "Project Orangepeel" 52 A.D
yeah I have to give the drivers side a "enh" push when I get out because it creeps up.
|
Re: "Project Orangepeel" 52 A.D
Looks great! love the hood props.
|
Re: "Project Orangepeel" 52 A.D
Thanks lower,I kinda stole the idea from Dad.
I just refined them a bit, Mark |
Re: "Project Orangepeel" 52 A.D
Hey Guys.
A small update I have been working on the truck for awhile (weather permitting) I have things off the list, but ran into a snag on my firewall. I ended up replacing the side pieces and leaving the stock ribs. After doing all this I hated the way the ribs looked, so cut them out and started over again! Will get some pics up later. Mark |
| All times are GMT -4. The time now is 06:13 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright 1997-2025 67-72chevytrucks.com