Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Thanks Guys

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Justin, Do you have the Calipers in stock?

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Yes we do have Black or Red in stock.Will need to know on your front rotors if you are running a 1 1/4 thick rotor or a 1 inch thick rotor.If you would like to place a order call us at the shop at (805)485-0382

Justin

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

It's a shame you can't see those calipers, but I wouldn't change those wheels, either. :lol:

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Happy birthday DELMO!!!

:ennyd:

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Wilwood D52 on NO PAINT

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Your frame and suspension are entirely too clean. You are obviously not driving it enough. :lol:

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Just went through the thread and the truck is awesome but the Lark is just over the top. I have a soft spot for the Buicks:flag:
Posted via Mobile Device
Posted via Mobile Device

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

nice calipers!!!! i got the same ones!! i dont have the baller rotors though ;/

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Just read through the entire post and I have this to say:
Kart, I am SOOO glad you're dad is cancer free!
No Paint looks awesome! My head is still spinning from all the ideas of seeing super cool stuff. You do seriously nice work, great attention to detail!

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Thanks Guys.. Creep only have 150 miles on it... still de- bugging it... updates Tuesday... been working on it all week... next show BilletProof Minnesota... June 8th

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Subscribed

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

nice stoppers!!

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Well Guys... After 4 different carbs... and a smaller bank account... We have determined that we have an issue with the fuel system... "No paint" will only run off of the front Moon Style tanks.. The Mustang tank located behind the rear axle will not flow fuel... zero fuel pressure... we are using 2 in line filters -6an and -8 an for lines...


How are you guys running your fuel lines? Do I need an electric pump? Also had a Billet Holley HP performer pump on it.. same issues... We have not installed fuel flow check valves in the system... but we have the parts to install.... any ideas guys... currently we have the "New Street Demon" carb built by Holley.. similar to the Q-Jet / Edelbrock carb...

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Holley ultra mech fuel pump... any ideas guys about my fuel issue... How are guys running there fuel lines with the Porterbuilt notch? :confused:

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

do you have a roll over valve and is it vented? no vent the tank will build up pressure and won't draw fuel

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

No roll over vent installed... Is that the issue ? I will call Tanks Monday AM.. Thanks...

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

This shows how the fuel lines are routed....any more ideas fellas??

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Well, We had our head ace mechanic here for 3 hours today , We found a few issues.

1) 1 bad Russell fuel shut off valve which would back feed fuel from the small 3.5 gallon tanks mounted in the box.

2) Installed Russell back flow check valves in main fuel line from back tank and also in the front tanks.

3) Re-installed Holley HP Billet fuel pump 7.5 psi pressure all good BUT... after 45 min. run time .. NO FUEL PRESSURE Again...... rear lines are Aeroquip -8 an lines / Moon Style tanks are all -6 AN Aeroquip lines also...

4) Also FYI... the tanks are vented and also replaced the TANKS Mustang style tank in the rear also... the 1st tank the pick up tube broke off in assembly ... man am I frustrated .... are the Aeroquip lines collapsing ?? :fb:

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

We are about out of ideas on this fuel issue? :confused::confused:

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

We are about out of ideas on this fuel issue? :confused::confused:

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Sorry I can't think of any ideas (3 tanks is a little above my pay grade). For troubleshooting, you could grab a bunch of cheap rubber fuel line and just run a temporary line from the tank to the fuel pump and see if that fixes it.

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Great thread and great build.

I'm no fuel expert, but I agree with cAlvis165.

I would also separate the three tanks for testing. 1 at a time with temp lines, then hard lines. Then add one at a time 'till all three are working or the problem is isolated to one system.

Please excuse me if you've already done this.

Dave.

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

Thanks guys.. It maybe an issue with the 18 foot on fuel line we have routed in this truck.. calling Holley tech. line guy today

Re: Extreme Powder Coating '65 C-10 Shop Truck
 

You get it figured out, man?