Re: How to: Ruin a perfectly good C10
Quote:
|
Re: How to: Ruin a perfectly good C10
I need to get around to this....bought tubular uppers but need to add the lowers. Part of me has been holding off tho...for a complete IFS from Scott's, Jim Meyer Racing, P.B., or others. Want coil over with rack and pinion front setup...IFS best way to get there I think.
Course its like my appetite....eyes always bigger then my.....................wallet! :lol: |
Re: How to: Ruin a perfectly good C10
1 Attachment(s)
Quote:
|
Re: How to: Ruin a perfectly good C10
I love the current look wouldn't change a thing, drive and enjoy it
|
Re: How to: Ruin a perfectly good C10
Quote:
Posted via Mobile Device |
Re: How to: Ruin a perfectly good C10
this truck looks terrific!!!!!
|
Re: How to: Ruin a perfectly good C10
Quote:
Posted via Mobile Device |
Re: How to: Ruin a perfectly good C10
Hurry up and get these control arms installed, we want some more pics
|
Re: How to: Ruin a perfectly good C10
Quote:
Posted via Mobile Device |
Re: How to: Ruin a perfectly good C10
Quote:
Now I got the "project parts blues" twitch again. :lol: |
Re: How to: Ruin a perfectly good C10
Quote:
Posted via Mobile Device |
Re: How to: Ruin a perfectly good C10
Cool truck. Another good build thread I can use for reference.
|
Re: How to: Ruin a perfectly good C10
Thanks, man. Looks like you've got it under control- nice build :chevy:
Posted via Mobile Device |
Re: How to: Ruin a perfectly good C10
5 Attachment(s)
I'm back in town and have a short break in the action before work picks back up again, so I've been working on getting the Bilsteins mounted up. Since I'm mounting them in other than the stock suspension setup, they're requiring a little bit of custom work.
First, I decided I needed to raise the upper mounting points, both front and rear, to keep the shock from bottoming out and to position them closer to their center-stroke 'sweet spot' at ride height. Out back, I decided I would modify my existing mounts by re-drilling the ECE relocator. This gives me just over an inch of extra travel and only adds around 2* of lean, based on my limited geometric/trigonometric calculations--luckily my wife's an engineer :lol: They ended up at just over 15" extended at ride height, which is just about in the middle of their travel. Perfect. After mounting them up, I took it for a drive, and WOW! I've heard good things about Bilsteins, but never experienced them first-hand. The truck feels completely different now; much softer, but more controlled feeling ride. I honestly was not expecting this much of a difference just from swapping shocks, much less the rears only. It is quieter, smoother, and and more composed. Money WELL spent. I'm anxious to see what the fronts do for the overall feel of the truck. |
Re: How to: Ruin a perfectly good C10
4 Attachment(s)
As for the fronts, I will be using the CPP/POL style upper relocators, which require loop style mounting instead of the frame-mounted stud. The problem with using the Bilsteins with these is that the shocks come with the upper stud permanently attached. No biggie there, as I just cut the end off and pressed them out, but had to special order bushings to fit the width of the mount.
The lower end had to be modified as well, due to the PB arms using a 5/8" stud instead of the stock arms 1/2" bolt. I originally thought I would just press the metal sleeve out of the bushing, but they were permanently bonded, so I picked up a set of Energy Suspension hourglass bushings and pressed them in their place. Worked perfectly--now I'm just waiting for the upper bushings to come in... |
Re: How to: Ruin a perfectly good C10
Bilstiens kick major a55.. one of the best out there IMO
Posted via Mobile Device |
Re: How to: Ruin a perfectly good C10
No doubt! I'm a believer, now. This answers your question on if they'll work with a 6" drop, too :)
|
Re: How to: Ruin a perfectly good C10
Nice fab work, and install. the shocks, just goes to show sometimes it pays to spring for the good stuff ! looks like it's time to throw out my abacus and brush up on my trigonometrics. lol
|
Re: How to: Ruin a perfectly good C10
Keep up the good work. Still taking notes:) watching and learning as you go.
Posted via Mobile Device |
Re: How to: Ruin a perfectly good C10
Quote:
Quote:
I'm still chipping away at it, but don't want to incapacitate the truck for too long, so the upgrades are getting broken down into manageable chunks. I'm thinking probably front C5 brakes next, since I can swap them out without affecting too much else (master cylinder, prop valve, lines, etc). The rear sway bar needs to wait 'til after I finalize rear ride height, which has to wait and see where the front ends up after the LCA install. I'll also prolly do the front shocks at that time to make sure my upper mounts line up well with the PB units. Rear discs will come somewhere in there after the fronts, which will be a pretty big job since I have to remove axles and swap out the master cylinder and prop valve in the process... Posted via Mobile Device |
Re: How to: Ruin a perfectly good C10
Don't remove the rear axles unless you need to replace seals and bearings.
I have seen alot of people just cut the backing plates in half and remove them,... without taking the axles out. (what are you going to do with the old backing plates anyway?) |
Re: How to: Ruin a perfectly good C10
Good job keep at it.
|
Re: How to: Ruin a perfectly good C10
That's great thinking out of the box I learn from guys like you every day
Posted via Mobile Device |
Re: How to: Ruin a perfectly good C10
WOW!! I just went threw your whole 38 pages. Nice truck man. Been wondering what you were building when i bought those parts off of you. Nice truck for sure.
|
Re: How to: Ruin a perfectly good C10
Quote:
Quote:
Quote:
Quote:
|
All times are GMT -4. The time now is 05:49 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com