Re: my build thread
2 Attachment(s)
Here are some pictures of my new hoods. Not sure what I'm going to do yet but I think the one on the truck right now will be easier to fix. Let me know what you guys think.
|
Re: my build thread
Tip from an old junkyard guy, Look for hoods from schoolbuses. There higher up so less likely to get damaged and retired earlier cause they were not allowed to transport public after a few years. I can still see 37 on the front of my hood even though it had been blasted primed and painted.
|
Re: my build thread
It's kind of hard to tell in the pics just how bad the one with center damage is. But if you can weld sheetmetal, I would think the one with the corner damage might be easier. If you can get that section from another hood, cut out the bad and weld in the good piece. Being on the side where there is more rigidity, there would be less warpage from the welding. On the other hand if the one with the center damage could be hammer and dollied out then that might be easier. To make that easier you could cut out the inner structure for easier access. Then weld that back in when done.
|
Re: my build thread
Got an idea today and started pulling the front end for my cross member conversion. Super hot here 113 today so I'm not sure how fast I'll get this swap done. I'll get some progress pictures up soon. Pulled one of my hoods apart and almost got most of the dents worked out of it. A little more finish work and it will look good and then I have got to spot weld the front piece back on it.
|
Re: my build thread
2 Attachment(s)
Little upate on my truck. I've got the front end all back on the ground now. I've got to make the steering box adapter and do the brakes then its all done. I cut my 12 bolt apart and now I've just got to mock that up and weld on trailing arm saddles. I went to the junk yard today and tried to trade my 7'' wide rally for a 8'' that I found and the guy said if I could find my recipt I could. I ran home and couldn't find it so I bought it for 20 bucks. I've got my hood cut apart right now and I'm some patch panels off of the green hood to repair the dents on the grey hood. I've got my glove box door back off and I'm doing a different design on it now. Here is a picture of the pinstriping I did on the back of my truck. I also bought a set of 1960 ish valve covers off eBay for when I get my small block going. I found an old air cleaner I need to get too. But thats it for now. I'll try to get some pictures up as soon as I get the rear end under the truck.
|
Re: my build thread
Quote:
|
Re: my build thread
1 Attachment(s)
Been awhile since I've updated this but not much has got done for a while. I got my axle all stripped down and my axle saddles just got here in the mail. I need to make a steering box adapter and do the brakes and then the front end conversion is done. I went scouting and found another 8'' wide rally wheel in the back of the truck that I got the 3 8'' ones and the 1 7'' wide wheel so now I'll have a matching set. Anyways I don't have any pictures other than this pinstriping one. Hopefully some progress pictures in the next couple weeks.
|
Re: my build thread
Good looking striping.....
|
Re: my build thread
Yeah :agree: That looks good!
|
Re: my build thread
Thanks dudes!
|
Re: my build thread
3 Attachment(s)
Little update. Got my steering shaft cut and re-welded today. And finished up my power steering box bracket. I had to cut it and re-weld it because I found out the on the 1960 frames the rear upper bolt is too high. So I moved my hole down on the steering box and fixed my adapter plate. I will take more pictures of the plate tomorrow. It is all finished now and has ground down corners and looks pretty good. I also cut the top off of my box so it doesn't have 2 holes. Now I just need to mount it up.
|
Re: my build thread
3 Attachment(s)
Got some work done on the hood yesterday. And the steering box almost all the way in. Picked up some .040 over flat top slugs for my motor and a good crank. Thinking about dropping the motor off to get bored next week.
|
Re: my build thread
3 Attachment(s)
Well finally some real progress for this build thread. I bought 2 stepside beds for 125 bucks. Sold one for half and picked up some year correct stepside fenders for 50 bucks. So in the process of thinking about shortening my frame I just decided I would rather build a custom back half from the cab back. I made it out of 2x4 and has a 7'' notch built in. The front tube is just in there to keep it square. And when I cut my frame and weld it in it will be a shortbed. All the bracketry is out of 1/4'' plate. It will be a wishbone style 4 link. The bed will have a false floor, should only lose half of it.
Attachment 524591 Attachment 524592 Attachment 524593 |
Re: my build thread
1 Attachment(s)
Here are the beds that I bought. The fenders I got are in perfect shape altho I don't have any pics of those right now.
|
Re: my build thread
Cool! Looks good :metal:
|
Re: my build thread
Looking good sam you must be the one at work looking for a tailgate? george was askin me about one.. I have the number to a guy who may have one... Truck looks great and the pinstripe in is killer looking....
|
Re: my build thread
Quote:
|
Re: my build thread
5 Attachment(s)
Progress! Got my bags in the mail, sold my long bed to order some more bags for the front. Dominator 2600's all around. Here are some progress pictures of the rear end.
|
Re: my build thread
Looking good looks like Im gonna have to finally get back to work on mine...
|
Re: my build thread
2 Attachment(s)
The rear end is coming together. I've got 2 more bags on the way for the front end. I'm really happy with how its coming together. :metal::metal::metal:
|
Re: my build thread
1 Attachment(s)
lower links
|
Re: my build thread
Looking good sam thanks for showin it off when I was down in the shop... I should have brakes by the end of today hopefully just waitin on the mail man for my powdercoat.. Also I have a pair of wheels for ya if you want them I just want them outta the yard..
|
Re: my build thread
Sure man I'll take them.
|
Re: my build thread
1 Attachment(s)
Here ya go Luke. I got it off the jack stands aired up then put it on the ground! Can't wait til its Z'd and that bumper lays.
|
Re: my build thread
Hey man looks good!! :metal:
|
All times are GMT -4. The time now is 06:00 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com