The 1947 - Present Chevrolet & GMC Truck Message Board Network

Page 4 of 4

Show 40 post(s) from this thread on one page

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)

- Blazer and Suburban Stuff (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=199)

- - MD Suburban metal cuts (https://67-72chevytrucks.com/vboard/showthread.php?t=792644)

m7vasque

11-30-2022 02:18 PM

Re: Suburban metal cuts

Quote:

Originally Posted by richard2717 (Post 9149878)

Here is some pics of the ones I have available at the moment. they have pcs of a hitch that would need cleaned off and the rear body mount holes could use a little work. $75 shipped for the pair .

.

Thank you. Will take a look after work and send a PM.

C130Nav

11-30-2022 05:23 PM

Re: Suburban metal cuts

Quote:

Originally Posted by richard2717 (Post 9149873)

Mike
It has been real wet here but I did find a box of brackets already pulled here in the shop. Is the pair of brackets shown here what you need? or is it the smaller single bracket you are looking for (would need to check outside for the matching side) The pair shown would be $75 shipped and they are very nice. I would need to see If I have a good 2nd bracket for the smaller if that is what you needed.

.

Richard,

yes, the 2 brackets on the right are the ones I need for position #3. The one on the far left might work; it looks different than whats on mine right now. Will have to look in the morning and check. Do you have another #3 bracket in better shape than the one on the right? The center one looks awesome; do you have another in that shape?

thanks

richard2717

12-01-2022 03:47 PM

Re: Suburban metal cuts

4 Attachment(s)

Mike
These are the best ones I have. The one on the outside is mostly surface rust but there are a few pits where the top turns to the side. I don't think it would be any problem at all structurally. There is no pitting in the body mount hole but it appears like the mount was worn out and the bolt was rubbing the edge of it. Both of them came from the same frame. Here are a few closer pictures as well.
Richard
.

C130Nav

12-02-2022 10:10 PM

Re: Suburban metal cuts

OK, those look good; I'll take them. Also the bracket for position #4 should work if you have both sides.

How about $100 shipped for all 4 pieces?

richard2717

12-05-2022 01:02 PM

Re: Suburban metal cuts

Quote:

Originally Posted by C130Nav (Post 9150915)

OK, those look good; I'll take them. Also the bracket for position #4 should work if you have both sides.

How about $100 shipped for all 4 pieces?

All the other 4th positions I have are no good. I am assuming I must have already sold the one from this set. I can do $100 for the 3 shown

C130Nav

12-05-2022 08:22 PM

Re: Suburban metal cuts

OK, that works. PM me with your payment info

richard2717

12-07-2022 03:36 PM

Re: Suburban metal cuts

Quote:

Originally Posted by C130Nav (Post 9152032)

OK, that works. PM me with your payment info

Parts shipped out today so you should have them Friday or Saturday with any luck. Post office says 2 days but who knows with them anymore.

C130Nav

12-17-2022 03:11 PM

Re: Suburban metal cuts

PM sent

richard2717

12-19-2022 12:56 PM

Re: Suburban metal cuts

2 Attachment(s)

Pics for C130Nav

Mike I found the 4th one. I sent you a pm

.

richard2717

12-20-2022 09:30 PM

Re: Suburban metal cuts

3 Attachment(s)

...

ajgriffin

01-08-2023 05:33 AM

Re: Suburban metal cuts

1 Attachment(s)

I know it isn't a metal cut, but any chance you have the washers that go on the upper control arm studs? I sent my front end out for powder with 4, but only 2 came home.

richard2717

01-08-2023 01:51 PM

Re: Suburban metal cuts

I can take a look when I get back home later today

ajgriffin

01-09-2023 11:50 PM

Re: Suburban metal cuts

Quote:

Originally Posted by richard2717 (Post 9164370)

I can take a look when I get back home later today

Thanks!

richard2717

01-10-2023 11:27 AM

Re: Suburban metal cuts

I have not been able to locate any as of yet. Have you seen this thread?

https://67-72chevytrucks.com/vboard/...d.php?t=589541

ajgriffin

01-13-2023 03:28 AM

Re: Suburban metal cuts

Quote:

Originally Posted by richard2717 (Post 9165047)

I have not been able to locate any as of yet. Have you seen this thread?

https://67-72chevytrucks.com/vboard/...d.php?t=589541

I have now, thank you! "Spherical washers" - learn something new every day!

All times are GMT -4. The time now is 05:48 AM.

Page 4 of 4

Show 40 post(s) from this thread on one page