Re: my 48 s10 swap
|
Re: my 48 s10 swap
|
Re: my 48 s10 swap
http://i7.photobucket.com/albums/y27...3/DSCN1599.jpg
this is what the fenders used to look like, then i used 80 grit and a wire wheel to take it all down and now im starting to fill http://i7.photobucket.com/albums/y27...3/DSCN1626.jpg this is down to bare metal http://i7.photobucket.com/albums/y27...3/DSCN1629.jpg i had the turn signal holes welded up The camera is down at the garage so i dont have pics of the body filler and work. I am working on the driver side fender now, i sprayed the inner fender with spray undercoating and must say it rocks. I taped it off more than i needed to and will come back with semi-flat paint so i can cover it all and so the spot where the inner fender meets fender and rad support it doesnt have problems because of the coating. After i get the driver fender done, (metal etch primer then epoxy primer) i will test fit the running boards and get those in expoxy primer. |
Re: my 48 s10 swap
can't wait to see that u-tube video of the engine firing up! looks like all that sweat is paying off. it will keep you busy this winter and be cruising just in time for the "thaw!" in the spring.
|
Re: my 48 s10 swap
Thanks for all the pics. Looks like your making some good progress.
|
Re: my 48 s10 swap
Quote:
I would think you could make it tight enough, how many openings do you have? As long as you duct tape the plastic to the floors and around your fans and filters and have it being sucked out you will be fine. so in other words yes :) |
Re: my 48 s10 swap
Nice project.
Just a quick tip for all you guys, I just finished bolting my truck together. Don't tighten all your bolt untill it's altogether. Box, fenders running boards, and splash aprons. It will save you lots of time in the long run. I've enjoyed reading all the builds, and nobody has mentioned this. Just my $.02. G |
Re: my 48 s10 swap
Quote:
|
Re: my 48 s10 swap
Hey guys, sorry for the slow update. Just recently picked up a hobart 140 welder. Pretty trick little machine, 110v, 20 amp. Hopefully before the new year i get the drivers fender in primer and get the brakes done and maybe the steering.
|
Re: my 48 s10 swap
glad to see you around happy holidays!
|
Re: my 48 s10 swap
Working on the steering and brake setup as its too cold to do bodywork. Does anyone here have experience with braided hoses(steel)? I think we might end up buying some fittings from anplumbing and making our own.
|
Re: my 48 s10 swap
For the brakes I used Russell lines from the calipers to hard line, got my own hard line from NAPA and cut, flared and bent my own. Bleed them out without any leaks. Flaring and bending is not that hard with the right (not cheapest) tools. Cheap benders will kink the lines. Use coat hangers to make templates for the bends. And remember to put the fittings on before flaring or you get more practice like I did! Mine are standard 45 degree double flares not AN lines.
|
Re: my 48 s10 swap
i have to make the power steering lines....im using a modified stock setup for the brakes i think!
lr |
Re: my 48 s10 swap
i was looking at my soon to be brother in laws camaro an the p/s line look like they might work.
|
Re: my 48 s10 swap
for sure let me know!! I went through the s10 and suburban lines already, they dont fit....its so frustrating because the pump is in a really poor spot and well its no fun
|
Re: my 48 s10 swap
take the line down to the local napa store or tractor supply. they can i.d. them and make you up the one you need or supply you with adaptors to make yours work.
|
Re: my 48 s10 swap
I talked to the napa guys and he said it would be 125-150 for a pair of hoses, now i only need one really but i cant remember what he quoted me, we will see where it takes us
|
Re: my 48 s10 swap
ok so im gonna focus on the motor and driving stuff now!! haha imagine that right. Gonna start getting the wiring ran and hooked up, along with the radiator and stuff. Anyone have idead of where to put my A/C and heat unit? im thinking in the middle of the dash because the glovebox on the pass side, gauges on driver side but the vent is in the middle....soo i have to figure out what to do about no room haha
|
Re: my 48 s10 swap
Quote:
[URL="http://www.off-road.com/trucks4x4/article/articleDetail.jsp?id=264312 They are braided steel lines, and with the fittings I have less then $100 into them. Good luck Marc |
Re: my 48 s10 swap
[quote=youngrodder;3081496]I made both of my hoses from parts from Summit racing. I got the idea from the following link.
[URL="http://www.off-road.com/trucks4x4/article/articleDetail.jsp?id=264312 They are braided steel lines, and with the fittings I have less then $100 into them. Good luck Marc[/quote] Yea ive found those too but dang $100 is still alot for some stupid lines. I am thinking more and more i dont have a choice on what i want |
Re: my 48 s10 swap
Quote:
My runs were also very short so I was able to buy (1) 3ft section of hose and cut if in half for both of the hoses that I needed. Most of the money was in the fittings. I do like how it turned out thought. Marc |
Re: my 48 s10 swap
Hey all, just a little update. Ill try and get some pics up sometime this weekend. I have most of the wiring harness installed. Just finishing looming the wires and getting them organized and all pretty. I have a 3 post GM starter and am kinda confused. Does anyone know what specifically hooks to each one? The big post is positive battery and ? off the alternator and the 'r' and 's' posts. I have the TBI harness hooked up to the big post and 's' post which is correct says painless performance.
I need to solder or crimp connectors on the VSS and ground it, finish the fuel pump/wire it. Brake switch and park/neutral switch to wire up. The mount everything. So the wiring harness is mainly done save a few things that are down the road. |
Re: my 48 s10 swap
Within a week or 2 i hope to have the trans pan dehumped and shifter mounted. First will be the dash holes i need to fix, then brake bracket, brake lines(brakes will be done done done!!) Then mount the steering column and figure out the 'holder'. Cut the DD shaft and steering is done!! Then i will have to finish the PS lines. And finally finish the gas tank debacle. Its getting exciting with getting motor wiring finished(or close) and doing the real mechanical stuff!!
|
Re: my 48 s10 swap
Another update, ill take pics this week and post them up. I got the dash holes all welded up, figured out the mount for the steering column, and got the brake bracket bolted up. I added a piece of steel for reinforcement and have since pulled it all apart to paint it. Next time im down at the garage ill bolt it all back up(and leave it that way!) I have a question for all you guys, how much does an typical v8 torque over when its revved up? im wondering for the steering.
|
Re: my 48 s10 swap
just read through this build looks very nice. subscribing.
|
Re: my 48 s10 swap
slow updates, busy busy with lots of stuff going on and working in freezing weather is no fun.
|
Re: my 48 s10 swap
Yeah man, your making some good progress. Everything looks great so far. Keep plug'n away.
|
Re: my 48 s10 swap
ugh, need to get pics up. I got the gas tank painted up all black and purdy like. Also finished the sending unit/pump assembly. A kind of exciting detail, i got the gauges in after much cutting and grinding on the old parts. I will explain with pics. So basically, gauges in, gas tank painted/ready for install, sending unit finished. I also worked on grinding off the remnants of the old seat frame and am about half done with that.
|
Re: my 48 s10 swap
also, you cant put trans fluid in a tranny w/o a yoke in correct? or it will all drain out the back? If so what would you guys suggest for that, i think if i lower it in the rear more it will throw off the driveshaft length but i want to start it before i get the bed on(bed has to be on to know how much to lower it). Any help?
|
Re: my 48 s10 swap
Quote:
|
Re: my 48 s10 swap
I just stumbled on this thread. Nice work.:metal:
|
Re: my 48 s10 swap
[QUOTE=Alan's Classic;3215551]I just stumbled on this thread. Nice work.:metal:[/QUOTE
Thanks!! hopefully progress will pick up this next month, im working on the other wiring harness and it should be in soonly!! |
Re: my 48 s10 swap
|
Re: my 48 s10 swap
http://i7.photobucket.com/albums/y27...7/DSC00544.jpg
oh yea.....:):):) |
Re: my 48 s10 swap
whatever happened to this thread?? is the truck finished? anyone know? I'm very curious to see it all finished!
|
Re: my 48 s10 swap
Quote:
|
Re: my 48 s10 swap
Glad to hear it's getting closer. I'm looking forward to seeing some more pics.
|
All times are GMT -4. The time now is 02:00 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com