Re: Parting this 66
 

Zeus
the heater core is also bigger in the deluxe than the basic
incase you need it as well

Re: Parting this 66
 

Craig I have a couple of the support brackets hanging on the wall. I will look and see what they are.
Jimmy

Re: Parting this 66
 

what is the difference in v8 to inline 6 radiator bracket?
I have a few different ones and not sure which is which

Re: Parting this 66
 

I think they are all the same since the radiator is the same for the 250, 283 and 327 according to most the parts houses. I have one I know is a 6 and one on my original V8 truck so I was just going to set them side by side.
Jimmy

Re: Parting this 66
 

Here is a pic of the bracket.
Jimmy

Re: Parting this 66
 

There are actually different upper brackets. They mount the same, but the "V-8" one is wider to accommodate a wider upper tank. The simplest way would probably be to just measure the inside opening of the bracket and see if it will fit over the tank you are trying to work with. There are also different lower mounts, in a different location farther forward the the larger radiator.

Re: Parting this 66
 

PM sent

Re: Parting this 66
 

Been desperately looking for original oil filter housing/canister for 305 V-6 if have one. Any suggestions? All threads on here about adapters seem worthless

Re: Parting this 66
 

Hi,
I need a Mount for my wiper Motor like this. Do you have some one like this ???

Thank you verry much.

Greetings

Nils

Re: Parting this 66
 

I have a 66 and that piece is still in it. I'll check it tonight when I get home from work and make sure its good. How much fire wall around it do you need?
Jimmy

Re: Parting this 66
 

Hi Jimmy.
thats great. I think i need a piece of 11" inch (ca.28cm) long and 8" high.

Thank you verry verry much.

Greetings Nils

Re: Parting this 66
 

That should not be an issue.
Jimmy

Re: Parting this 66
 

Thank you verry much
Nils

Re: Parting this 66
 

Hi Jimmy,
Is the Motor Mount ok ? Do you have a picture ?

Thank you verry much.

Greetings

Nils

Re: Parting this 66
 

Mount is OK just been raining the last two days and I have not been able to get it cut out. Rain should be done this morning and will cut it out after work. Will take a pic of it when out so you can see it.
Jimmy

Re: Parting this 66
 

Hi Jimmy,
Ok thank you verry much.

Nils

Re: Parting this 66
 

Got it cut out. Here are a couple of pictures. $20 and what ever it takes to get it to you.
Jimmy

Re: Parting this 66
 

Hi Jimmy,
the Mount looks great. 20$ is ok. Is PayPal ok for paying ?
Could you say me how much is Shipping costs to Germany ?

Thank you verry much

Nils

Re: Parting this 66
 

Nils I sent you a PM to get your shipping information. Think about if you need anything else to go in the the box.
Jimmy

Re: Parting this 66
 

Do you have pictures of the accelerator pedal?

Re: Parting this 66
 

Jimmy I need a section of the windshield frame. Drivers side bottom corner outlined in tape in the picture. About 6" high and 8" wide. Thanks for the help.

Re: Parting this 66
 

Ill look to see if it is any good.
Jimmy

Re: Parting this 66
 

Thanks Jimmy

Re: Parting this 66
 

Not sure what I have is much better than yours. Drip rail is rusted off of it and looks pretty pitted in about the same spot as yours.
Jimmy

Re: Parting this 66
 

Thanks for checking Jimmy I guess I'll keep looking
Dale

Re: Parting this 66
 

Hi and thank you in advance for fielding this. I am looking for what I believe is called a Parking brake cable clamp. It's bolted (two bolts) to the rear brake back plate were the parking brake cable goes into the back plate.

Re: Parting this 66
 

I would have to look. LMC does sell them. Call it a seal.
Jimmy

Re: Parting this 66
 

thanks. Let me know. I have a 4x4 3/4 ton so don't see it in LMC or many others.

Re: Parting this 66
 

Well that changes things. What rear do you have? I thought you were looking for C-10 stuff.
Jimmy

Re: Parting this 66
 

Les here is the pulley.
Jimmy

Re: Parting this 66
 

Jimmy,

Thanks for photo, could the number be 3923898?

How does the pulley grove/ belt area look?

Thanks,
Les

Re: Parting this 66
 

Yes that could be the number. A little surface rust from sitting and will clean up fine. I can put it in the lathe and clean them in short order.
Jimmy

Re: Parting this 66
 

Jimmy,

PM sent

Les

Re: Parting this 66
 

Sorry I'm late to the conversation .... if you still have this bucket of rust are you willing to cut a donor panel off the cab?? I need passenger side, cab rear corner/back of cab. I can provide more specifics if this is something you are wiling to do. Note: I understand that the bottom rear cab corner is always rotted out ... what I need is kind of from the horizontal body line (mid-height on the cab) to the bottom of the cab from the door jam around to the back of the cab to the place where the back of the cab has the first pressed indent below the back window. Anyway; let me know if this is possible. Thanks, Rod

Re: Parting this 66
 

It left for the scrap yard Saturday.
Jimmy

Re: Parting this 66
 

Dang! Timing is everything! My loss. Thanks,

Re: Parting this 66
 

Looking for a cast iron V-8 manual trans bellhousing. was this an 8 or six? Stick or Auto?

Thanks,
Larry W.

Re: Parting this 66
 

I sold the one in this truck. The bell housings will fit either engine.
Jimmy

Re: Parting this 66
 

Do you have a choke cable and knob?

Re: Parting this 66
 

I may Will look today.
Jimmy