![]() |
Re: How about some pics of bagged 47-59
Good looking green G M C !
|
Re: How about some pics of bagged 47-59
2 Attachment(s)
Was able to get a better pic of the 57, aired up and down
|
Re: How about some pics of bagged 47-59
Love the GMC
|
Re: How about some pics of bagged 47-59
Nasty looking.:sumo:
Mudman. |
Re: How about some pics of bagged 47-59
Quote:
|
Re: How about some pics of bagged 47-59
Gigamanx, I think I have the same question.
Getting ready to plumb my airbag system and would like to hear experiences with either hard or soft line too. DOT approved push-in fittings are kinda expensive and I hear a lot of guys complain about chasing down leaks. My plan is to plumb the airbags in -4 AN fittings (1/4" tube) with aluminum line. Stainless might be a better option, but it is difficult to flare without cracking and the fatigue resistance of the aluminum should be ok if it is fastened to the chassis correctly. To keep the cost of down for the AN fittings, I'm using steel JIC fittings, nuts and sleeves. I have a Parker Rolo-flair tool to make the flares in the aluminum and have had good luck making leak free connections with it. For the threaded connections, the plan is to use a anaerobic thread seal (Locktite 565) instead of teflon tape or pipe dope. Any other suggestions from guys with bagged trucks? |
Re: How about some pics of bagged 47-59
there isn't much difference in either setup, more aesthetics rather than function. I had no problems with soft line and PTC fittings. I used blue monster tape on threads. I used 1/2 lines on my last bagged truck with accuair manifold. Current one Im using 3/8 with manual valves. I'm sure you may read plenty of debate out there, but I'm just giving my take with it.
|
Re: How about some pics of bagged 47-59
What's your ride height aired up?
|
Re: How about some pics of bagged 47-59
I recently bought this truck, will measure ride high tomorrow,
|
Re: How about some pics of bagged 47-59
I am using 3/8" lines Accuair valve. I ran rubber air line up front and have PTC nylon line out back. So far 10,000 mi all good. My truck is 5000lb.
|
Re: How about some pics of bagged 47-59
Quote:
|
Re: How about some pics of bagged 47-59
Sorry I didn't mention that is was a Jag IRS - and there's no C notch. It was narrowed about 3" side to side and tube steel half shafts replace the Jag's forged half shafts.
https://talk.classicparts.com/media/imag0291.6811/full The ladder truss supports the differential and is mounted on urethane bushings. The bolt that hang the diff in the truss are about even with the bottom of the wood boards in a stock bed. https://talk.classicparts.com/media/imag0293.6809/full This bracket assembly holds the differential assembly in position and keeps the pinion angle constant https://talk.classicparts.com/media/imag0273.6802/full The airbags ride on a trailing arm that connects to the Jag's LCA. It is a 5" Slam bag that does the same job as the Jag's coil-over springs. https://talk.classicparts.com/media/...rbag.6686/full Another photo https://talk.classicparts.com/media/...-too.6685/full The front of the airbag trailing arm - it has the same roll center as the LCA of the Jag IRS https://talk.classicparts.com/media/...-arm.6684/full And yes. a four link and a c-notch would have been a lot easier. But it's all about the nostalgia of the Jag rear end |
Re: How about some pics of bagged 47-59
Oh, and here's a photo of the truck with the running boards on sitting on the bump stops. There's about three inches from the running boards to the concrete floor.
https://talk.classicparts.com/media/...ds-1.6892/full |
Re: How about some pics of bagged 47-59
The jag rear is well worth it, top notch job.
Mudman. |
Re: How about some pics of bagged 47-59
When I was a kid in the 60's, a lot of the plastic model kits of hot rods had Jag rear ends - I'm sure there's better solutions out there, but it is all about the nostalgia and childhood memories.
Thanks for the compliment, Mudman! |
Re: How about some pics of bagged 47-59
Well you know many won't see it or even know what it is but...you do and I think of that on my own builds, it's about what we want and like right, but cool when others appreciate what we've built too. Keep at it, very nice build.
Mudman. |
Re: How about some pics of bagged 47-59
Quote:
|
Quote:
Posted via Mobile Device |
Re: How about some pics of bagged 47-59
Very nice GMC man,
Make sure you get a couple of linear actuators so you can flip a switch and make your wood bed open, Be a shame for others not to see your work. Very very nice. To me, its always whats on the inside... |
Re: How about some pics of bagged 47-59
Thanks for the nice words!
At this point, I just want to drive it! No more 'enhancements'/science projects. |
Re: How about some pics of bagged 47-59
2 Attachment(s)
[attach]Attachment 1753100[/attach] 1951 looooong bed
|
Quote:
Posted via Mobile Device |
Re: How about some pics of bagged 47-59
1 Attachment(s)
New wheels.
Attachment 1753213 |
Re: How about some pics of bagged 47-59
Quote:
Quote:
|
Re: How about some pics of bagged 47-59
Quote:
|
All times are GMT -4. The time now is 12:57 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com