Re: What did you do to your truck today.The 3rd chapter
4 Attachment(s)
Added a couple of GM Chicklet emblems to the Ramp truck and worked on the 71 C-10 mirror mount for the late model mirror.:chevy:
|
Quote:
Posted via Mobile Device |
Re: What did you do to your truck today.The 3rd chapter
3 Attachment(s)
Pulled a 700R4 from a 93 5.0 Caprice at the local Pick-n-Pull today. Picked up a mechanical speedo while I was there. Was not fun lifting it into the back of the car by myself. Thankfully, my daughter was able to help me lift it back out at home. Will be rebuilding it over the next month or two while my truck is at the body shop getting some old damage repaired.
|
Re: What did you do to your truck today.The 3rd chapter
Finished wiring for aftermarket tach, finished installing radio and replacement speaker for the factory AM (turnswitch.com for the correct ohm speaker), installed PS pump and primed/bled the system, and took a run over to Fremont, CA and met with Bill at Vintage Chevy Trucks for a fan shroud. Ended up with correct bumper brackets, decent outer grill shell and center bracket/hood release along with the shroud. Should be able to have the radiator and support installed and the cooling system filled. Maybe break the motor in on Tuesday or Wednesday finally!!
|
Re: What did you do to your truck today.The 3rd chapter
5 Attachment(s)
My friend said it's about ready for paint. Bed ready, cab should be ready tomorrow. Helping him again tomorrow.
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Changed the lube in the rear end, cleaned and painted the cover...installed the refreshed jack hold down hardware, and did some final sanding on the '67 steering wheel.
...and got the look from the wife for spending the day in the garage! |
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Working on PJM's look. Haven't swapped it out yet but reconstruction is done.
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Quote:
Did you have to redo any of the handle area. I have a 67 stock wheel I cut down but haven't finished it yet. I'm not sure what to use on doing the handle area that is gone.:chevy: |
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
.
Did a reset on the EFI unit which means I now have to go through Initial tuning procedures and then let it relearn from zero...hoping to solve some idle issues and get overall better results. This should have been done post top end rebuild anyhow! |
Re: What did you do to your truck today.The 3rd chapter
3 Attachment(s)
I'm gonna swap out my ho52 with a Dana 60. I buttoned up the 60 and geting.ready to do the swap.
|
Re: What did you do to your truck today.The 3rd chapter
2 Attachment(s)
I test fit Blue in th shop too. I think I need to move the beer wagon though....lol
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Yeah, I noticed they sold me the 11 inch lever. I swapped it for the right one. Good eye though.....
|
Re: What did you do to your truck today.The 3rd chapter
3 Attachment(s)
I took some pictures as the new owners came to take the '71 away today.
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
-klb |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
I have used POR15 before. 1 pound in the smallest package it is available in, $33-$35 bucks. It's nice for larger areas like that, easy to work and a longer working time.
JB Weld steel stick is good for crack filling. It is a grey color which is nice for darker wheels and such. The only down side is it starts curing up quick. Says 5 minutes... As long as you cut off a small chunk at a time and work one crack at a time you're good. Have to try not to over do it tho because obviously it will take a lot of extra sanding to shape and smooth out |
Re: What did you do to your truck today.The 3rd chapter
I bought a 7042210 carb today off of Market place.
|
Re: What did you do to your truck today.The 3rd chapter
2 Attachment(s)
This summer will be sooo much more enjoyable here in Florida. Got the AC installed.
|
Re: What did you do to your truck today.The 3rd chapter
Replaced front and rear bumper brackets.
Installed front and rear bumper. |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
66clow, can you start a thread and show how you ran your A/C lines. I haven't done mine yet and am always looking for a better way.
|
Re: What did you do to your truck today.The 3rd chapter
since getting my truck back from my brother its not what have I done to my truck today but what I have done everyday LOL!
In the last week I have: Got my Side Mounted Rally spear tire installed - took a 8 inch bolt from ebay! removed my radio and ordered a new Classic Sound radio/speakers from http://garytayman.com/ Bought a white radio delete plate here on the forums and installed yesterday (thought I was going to be without a radio longer, so that will be for sale soon) re-did the dash with properly painted lens and replaced the tin from 70shortfleet Replaced hard as rock/splitting vacuum lines for ducts (starting from reservoir to dash). Found out I have a original GM key but the keychain had worn a hole so big the middle values where gone (LocDoc sold me a glovebox lock and is making me two new keys that match my truck). The fun does not stop there, parts on the way for days to come! Like rubber stops for the glovebox. Screws / j-nuts for the headlight bezel and other screws/spings for the headlight cans. |
Re: What did you do to your truck today.The 3rd chapter
No pictures sorry, but changed the carrier bearing while the driveshaft is out of the truck.
Changed rear diff fluid. Had exhaust manifold crack brazed, media blasted and painted it. Removed battery box, media blasted the rust off, primed it and started first coat of paint. Removed all core and oil galley plugs. Blew out all passages with air and ran brushes through all holes. Chased all threads Cleaned all lifters and cleaning pistons and pushrods Started the hone cylinder #2. It has a couple of pretty good scratches in it and will determine if I have to got to .30 over (I will hone it with my 3 stone hone until scratches are out and the remeasure to see if bore is in spec). I really think I should just send block to machine shop and go .30 over. |
Re: What did you do to your truck today.The 3rd chapter
since getting my truck back from my brother its not what have I done to my truck today but what I have done everyday LOL!
In the last week I have:
The fun does not stop there, more parts on the way for days to come! Like rubber stops for the glovebox and hood sponges. Screws / j-nuts for the headlight bezel and other screws/springs for the headlight cans that seem tired and loose. I even got a Glovebox light kit that is coming my way! I am sure I even have forgotten things I have ordered - its going to be like Christmas when packages arrive! LOL |
Re: What did you do to your truck today.The 3rd chapter
2 Attachment(s)
I finally got to start working on converting to front discs last night. I ordered a kit several months ago, and the supplier had to shut down due to COVID. I ended up canceling my order with them, and got a Western Chassis kit from Performance Online instead. They were able to ship within three days of placing the order. The kit arrived the day before we left town for a week, so all I had time to do was paint the drop spindles and calipers. We're finally back home, so last night I tore everything apart. I will be drilling out the upper ball joint rivets and pressure washing the control arms tonight.
|
Re: What did you do to your truck today.The 3rd chapter
Wow Rich, so much fun you did it twice. LOL
|
Re: What did you do to your truck today.The 3rd chapter
That was not fun at all - though I am getting faster at it! So much so, I'll likely be doing the dash cluster *for a 3rd time* because I am getting dash light bleed-through into my left turn signal! I am thinking perhaps during the radio install, instead of pulling the cardboard glovebox out again I'll go from the dash cluster side. That thing is not so easy to get out (I have A/C) and it is already getting slightly damage in the upper left corner.
I just have to figure out how to seal the cardboard indicator tubes to the tin. The little seals that go under them are hard as a rock and I cannot find where to buy replacements. |
Re: What did you do to your truck today.The 3rd chapter
2 Attachment(s)
Daughter wanted to have a drive, so i took some photos. So that is what I did today, took some pictures LOL
|
Re: What did you do to your truck today.The 3rd chapter
2 Attachment(s)
New starter . Couldn't get the rebuilt to work properly
|
Re: What did you do to your truck today.The 3rd chapter
Not mine, but we put a couple of bed side tool boxes on my son's brand new 2021 Colorado.
|
Re: What did you do to your truck today.The 3rd chapter
4 Attachment(s)
Was working on installing a disc conversion kit earlier this week, but discovered control arms on passenger side were bent. Found a set of replacements locally and dropped them off to be sandblasted.
Today I cleaned a set of Vortec heads and a 700R4 transmission I will be rebuilding. Also removed a sheared off exhaust bolt I discovered in one of the heads. |
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Spent the day installing a CustomAudio Sound Radio and while I was at it, popped in a LMC Glovebox Light too (man that little light from LMC is C H E AP).
Notes about Radio at this thread |
Re: What did you do to your truck today.The 3rd chapter
Ordered my 350 HO crate engine from local Chevy dealer.
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Body and paint, the final frontier...
|
All times are GMT -4. The time now is 08:10 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com