|
Re: My Dusty 71 GMCe Electruck
Long weekend at the wrinkle nose garage, Earl has some undo time and a half coming....Happy 4th Gregski.
|
Re: My Dusty 71 GMCe Electruck
Quote:
|
Re: My Dusty 71 GMCe Electruck
3 Attachment(s)
upper control arm bump bumps
Fun Fact: only reason I opted to run sum is to keep the 2" lowering coil springs from falling out when jacking up the truck |
Re: My Dusty 71 GMCe Electruck
1 Attachment(s)
so guess what? I'm redoing the driveshaft turns out the Lexus drive shaft has the center bearing support bracket on the wrong shaft (differential side instead of transmission side) so it aint gonna work out for me, so three drive shafts later...
I'm gonna post a video explaining all this so please stay tunned |
Re: My Dusty 71 GMCe Electruck
2 Attachment(s)
so I thought I would clean up the center bearing drive shaft support cross member just a tad
yes all that dirt is just from the back side of the center crossmember, wait till you see how I cleaned the other side |
Re: My Dusty 71 GMCe Electruck
5 Attachment(s)
ah yeah, I am not even kidding there were some things stuck so hard I could not get them off by hand using a putty knife nor a flat screw driver
|
Re: My Dusty 71 GMCe Electruck
5 Attachment(s)
new old bracket fits
|
Re: My Dusty 71 GMCe Electruck
4 Attachment(s)
well I was driving myself crazy so I decided to make brown things gray
thanks be to a forum member who hooked a brother up with two proper upper coil ear lobes (I'm sorry but once you see them you can't unsee them) |
Re: My Dusty 71 GMCe Electruck
1 Attachment(s)
how many details does my devil have?
|
Re: My Dusty 71 GMCe Electruck
3 Attachment(s)
there, happy now?
|
Re: My Dusty 71 GMCe Electruck
2 Attachment(s)
decided to throw sum luv to the threaded nails as well
|
Re: My Dusty 71 GMCe Electruck
2 Attachment(s)
Wife: "Honey have you seen our aluminum foil, I can't find it?"
Me: "Now what would I be doing with our Reynolds Wrap in the garage, come on now?!" also Me: |
Re: My Dusty 71 GMCe Electruck
1 Attachment(s)
all powder coated and ready for reassembly (and no that one missing washer is not bothering me at all, NOT ONE FRIGGEN BIT, ok, there I said it)
|
Re: My Dusty 71 GMCe Electruck
1 Attachment(s)
I swear this happens to the same finger every time, can anyone relate?
|
Re: My Dusty 71 GMCe Electruck
4 Attachment(s)
|
Re: My Dusty 71 GMCe Electruck
3 Attachment(s)
I like to use a jack hammer to open these cans
Top Tip for best results: Stir it very well... then stir it sum more! |
Re: My Dusty 71 GMCe Electruck
3 Attachment(s)
how much does one can cover?
and what's it look like up close? |
Re: My Dusty 71 GMCe Electruck
Busy day! Looking good.
|
Re: My Dusty 71 GMCe Electruck
Quote:
|
Re: My Dusty 71 GMCe Electruck
2 Attachment(s)
decided to weight this bad boy, this is the 1 1/16" stick (the smaller of the two)
|
Re: My Dusty 71 GMCe Electruck
2 Attachment(s)
mandatory stare and compare before I go mount the rear boingers back on
|
Re: My Dusty 71 GMCe Electruck
1 Attachment(s)
so motivated by Bill Bayer I decided to take another stab at the Prius power steering doo dad, I was not happy with it under the dash
Power Steering - Tesla Jeep |
Re: My Dusty 71 GMCe Electruck
2 Attachment(s)
so here we go time for surgery
|
Re: My Dusty 71 GMCe Electruck
4 Attachment(s)
The Pull-A-Parter 3000
Sketch Level: EXPERT |
Re: My Dusty 71 GMCe Electruck
2 Attachment(s)
American Polack Potrafi
Pull-A-Parter 3000 complete kit with attachments also available in metric |
| All times are GMT -4. The time now is 10:01 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com