![]() |
Re: 1963 C-10 in NC
Lookin Great Brotha!!! Not lookng forward to mne though... Lol
|
Re: 1963 C-10 in NC
Quote:
I did a few "test places" in the fleetside Saturday since we had 2" of rain. The red rattle can is coming off nicely, but the black was sprayed with real paint and will probably get the same treatment as the stepside.....so the process will begin again. I'm hoping to locate a donar dash for the fleetside since it needs so much work to make it right again. If I can find a decent donar, then I'll spend the time to repair this one. |
Re: 1963 C-10 in NC
3 Attachment(s)
Got the new headers in...2" primaries hedman htc, got the pol mounts in and painted last week. So...engine out this weekend, new toys bolted on and then trans mount install.
|
Re: 1963 C-10 in NC
Got the headers from a forum member running the same combo, but his trucks lowered and it lowered his exhaust to far. Im at stock height on a taller tire, so we should be golden...but say your prayers to the truck gods for. Will be glad to have this bump overcome.
|
Re: 1963 C-10 in NC
Cool!
|
Re: 1963 C-10 in NC
Got the driver side door about 90% ready to paint. Will do rest and pass side tomorrow. Now that parts are here im ready to get drivetrain completed.
|
Re: 1963 C-10 in NC
I just got caught up on your progress. You got alot done while I was off on vacation.
Parts and interior work is looking good! |
Re: 1963 C-10 in NC
Those headers look beautiful. So do the engine towers for that matter.
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
New Headers and towers...:metal:
|
Re: 1963 C-10 in NC
1 Attachment(s)
Was a late day of work, so took the time to just clean and polish up the cluster. Still looks good from restore I did in 2010. I want to seperate turn signals and add a few more lights in the open places on the back. Also want to add some grounds.
|
Re: 1963 C-10 in NC
well at least ur gonna start with 3/4 of a tank of gas according to the gauge!!!
|
Re: 1963 C-10 in NC
Haha...right. all gauges working good prior to pulling, so just used a clean paint brush to knock off any dust, polished the lens, polished and waxed the chrome and pulled some light fixtures off an old harness so color and sockets are correct.
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
I keep a full set of back up gauges for both clusters, but they all read correct and ive only lost a fuel and temp gauge in 20 years. Have had a speedo rebuilt and worm gear replaced, but the gauges were built good and the speedos loosing calibration is the most common issue.
Bowtie bits put a new resistor in a fuel gauge, I used my back up and that ones in the spare box now |
Re: 1963 C-10 in NC
Quote:
Doesnt take much. Lay the lens on a thin towell over a hard surface. Polish with paste and shirt. Wipe clean. Polish again with clean cloth. I use circular motions and it has taken off overspray and light scratches. Smells decent too unlike most of the products we use. Repeat if needed. |
Re: 1963 C-10 in NC
Looks sweet! :chevy:
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
4 Attachment(s)
More cab prep done today. Pulled tank, door gaskets, vents and were really close to paint. Got underdash covered and masked off. Need an extra set of hands to pull glass. Minor work left and primer/paint.
|
Re: 1963 C-10 in NC
4 Attachment(s)
For some reason my phone flipped all the column pics....I'll try again. Doing more prep Saturday....got the 4 speed column cleaned up, prepped, primed and painted. Hadn't touched a compressor gun in near 20 years and no runs in the paint so I was well pleased with progress.
I stuck with spraying outside until the big barn is up...will start work here in a few weeks on that. Luckily, no bugs or debris in paint. We'll mask off the carport with plastic when we do the interior and hose down the floor after a good clean out with the leaf blower. Not the most ideal spot, but its working for now. Got the parts moved into the tool shed to sit overnight. Good thing to, since our weather guy didn't mention the rainstorms that came through about 2 hours after I finished spraying. I know this is small stuff, but I wanted some practice with the new gun before I tackle the cab. I think it'll be ok, so color this week once the rain passes through mon/tues. |
Re: 1963 C-10 in NC
Can't wait to see the interior painted!
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
Looks like Austin and I will link up tonight and get the windshield and back glass pulled. Ordered up paint and clear coat for the interior and pick it up and lunch....so hopefully color this weekend.
|
Re: 1963 C-10 in NC
Quote:
|
All times are GMT -4. The time now is 04:57 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com