![]() |
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
I think he is talking about the plug that goes in the hole that the clutch linkage passes thru on the firewall to the Z bar.
Trucks are looking good. |
Re: 1963 C-10 in NC
Yeah....I could definitely use one. I was going to weld it up, but I'd rather have the plug.
|
Re: 1963 C-10 in NC
2 Attachment(s)
Got the glass removed last night with help from Austin. Pinch welds all look great. Some light surface rust on the lower corners, but not rot or pinholes...and nothing the wire brush didn't take off. Should be able to finish prep on windshield opening....tape off and primer the rest of the interior tonight. MY goal at least. Hoping to get color down over the next weekend and start reassembly. Then back onto engine/trans.
|
Re: 1963 C-10 in NC
5 Attachment(s)
Got seam sealer down last night. 2 coats sealer and 2 coats base so far. Need 1 more coat base and then clear
|
Re: 1963 C-10 in NC
Diggin' the Blue!!!:metal:
|
Re: 1963 C-10 in NC
5 Attachment(s)
Up to 3 coats color..1 clear
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
5 Attachment(s)
No problem.
Last coat clear down. Came out great. |
Re: 1963 C-10 in NC
DANG!!! Looks terrific! :metal::metal::metal:
|
Re: 1963 C-10 in NC
Not bad for outside, 20gal portable compressor and home depot husky spray gun. Finish came out great, no runs
|
Re: 1963 C-10 in NC
Looking good!
|
Re: 1963 C-10 in NC
5 Attachment(s)
Quote:
Heres a few more pics of finish. 1st one ive sprayed in 18 years. |
Re: 1963 C-10 in NC
1 Attachment(s)
Will do the doors this week and then prep exterior of the cab.
|
Re: 1963 C-10 in NC
In case any ones interested:
Primer omni mp281 lacquer Base omni dark pepsi blue 12908 Clear shop line jc630 polyurethane And the clear hardner 4:1 shop line jh6370 polyurethane |
Re: 1963 C-10 in NC
1 Attachment(s)
Got the glass sealed into the gasket tonight. Will get the trim in tomorrow or monday. Lots of tape
|
Re: 1963 C-10 in NC
5 Attachment(s)
Some more headway inside the cab. Got most of the dash switches in. Floor vents and cab light in. Taped off and sprayed the rear of the cab. And masked off the firewall and touched up the undercoating there.
|
Re: 1963 C-10 in NC
3 Attachment(s)
Few pics of the dash.
Also did the window trim install just a few minutes ago. Undid one 1/4 of the tape, installed trim piece. Ewtaped using what I just removed and repeated process. The trim is the 60-61 wide trim and really makes the glass look good. |
Re: 1963 C-10 in NC
Lookin' Good Brother! :metal:
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
looks really good and i like that color of blue also. hard to believe it was painted outside... nice job.
|
All times are GMT -4. The time now is 05:07 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com