![]() |
Re: My 63 Project
1 Attachment(s)
Put my new springs in today. This is the frame before.
|
Re: My 63 Project
1 Attachment(s)
And mocking up the new springs. Supposed to be four inch drop springs.
|
Re: My 63 Project
1 Attachment(s)
And now the frame... After the install. Does my math not add up???
|
Re: My 63 Project
To get an accurate measurement, you're going to need to have the bed installed and be at close to your final weight on the rear suspension. I think you're going to be OK.
|
Re: My 63 Project
Quote:
|
Re: My 63 Project
1 Attachment(s)
Shaving some bumper bolt heads. Two down, four to go.
|
Re: My 63 Project
1 Attachment(s)
Getting pretty good with this "rattle can" primer!!!
|
Re: My 63 Project
1 Attachment(s)
And the dash.
|
Re: My 63 Project
1 Attachment(s)
Spent some time today working on my door panels.
|
Re: My 63 Project
1 Attachment(s)
Notice that one of them has holes for the arm rest. That has to go.
|
Re: My 63 Project
1 Attachment(s)
Little bit of welding.
|
Re: My 63 Project
1 Attachment(s)
Little bit of grinding.
|
Re: My 63 Project
1 Attachment(s)
Little bit of filler.
|
Re: My 63 Project
1 Attachment(s)
Little more sanding, ready for primer and paint!
|
Re: My 63 Project
1 Attachment(s)
And with a couple coats of paint.
|
Re: My 63 Project
1 Attachment(s)
Ok, so now I need some help.
How do I get the gas tank mounts out?? Obviously there are two bolts that come up from the bottom, but it looks like the mounts are spot welded to the rear of the cab. |
Re: My 63 Project
I think they are spot welded to the floor as well... IIRC 66Farmer did the cleanest removal of those that I have seen on this site.
If you dont already have a spot weld cutter, you may want to get one. |
Re: My 63 Project
Just found your build...:mm:
Great start, I'm in for the ride...:metal: |
Re: My 63 Project
1 Attachment(s)
Thin layer of filler on the fender.
|
Re: My 63 Project
1 Attachment(s)
Workin on the door.
|
Re: My 63 Project
About four hours with that air file in my hands is about all I can take. It will wear you out!!
|
Re: My 63 Project
Quote:
|
Re: My 63 Project
Nice work! Yer doing great! :chevy:
|
Re: My 63 Project
Quote:
A light hammer and a sharp punch will usually give you enough of a indent for the weld cutter to ride in until you get a good circular channel started. But not always, so keep another drill handy with a bit in it that is just a tad larger than the spindle on the weld cutter. This will give your weld cutter the stability over uneven spots to get the job done. On the back of the cab be very cautious when cutting else you will be plugging holes you didnt need to (I tried using an air chisel and learned the very hard way). Remember the spot weld cutter is sharp, and fast, if you are not paying 100% attention you will cut dime size holes clean through both layers of steel. In my tiral and error learning I found that it was better to under cut it, and tap tap tap with a chisel between the two welded pieces, than it was to cut all the way thru. I hope this helps you (hopefully you read this before you get hands on the project) and good luck !! Here is the build I was looking for, a great fellow doing an awesome build: http://67-72chevytrucks.com/vboard/s...=513377&page=6 |
Re: My 63 Project
Quote:
|
All times are GMT -4. The time now is 07:48 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com