Re: 68 aka "Chained in Porterbuilt Prison"
Very interested in watching how you are gonna use that sweet floor shifter!
|
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
http://www.ebay.com/itm/330577808927...84.m1423.l2649 But the six speed shifter plate has a rubber boot in the round area U see in the plate above--I think would be totally cooler using the 6 speed boot and the auto shifter rather than the kind of MECHANICAL LOOKING plate above--Make every one go--"Is it 6 sp or auto"??? The console is in pics in post 45...here is a pic of complete with 6 spd shifter but ot a real good pic of plate........jim http://www.ebay.com/itm/03-06-CHEVY-...item3f013f9ea2 |
Re: 68 aka "Chained in Porterbuilt Prison"
Agree. The six speed boot looks way better, and less "late 90's early 2000's" design.
|
Re: 68 aka "Chained in Porterbuilt Prison"
Jim,
I can't believe I didn't see this over here! Awesome work man! I love the dash. I agree with you, the stock dash is what I like least about these trucks. The stock one was cut out of ours long ago! I'm subscribed. Keep it coming! Posted via Mobile Device |
Re: 68 aka "Chained in Porterbuilt Prison"
I'll let the cat of the bag-sort of----Instead of shaved handles-think of Ring Brothers Gen 1 handles !!!!!!!!!!!!!
|
Re: 68 aka "Chained in Porterbuilt Prison"
5 Attachment(s)
Ok guys a little wkend report--2 cold to finish body work on dash so I took bed apart last week and finish 1 bedside today--Floor will be raised 10 inches-I am not a fan of notch covers so I will raise complete floor --Started on dr. side panel--Reverse mini tub-wood will set on top of angle-Little trick here-always plug weld angle to wall before cutting out below-that way no flexing on the side panel-That's 1x2 tubing between bedside and inner panel-all pieces touching outer bedside are done with 3m panel bond --Tub bolts in-will be 6-7 " wider than pic-That's one half-The tub will have a 1 1/4 flat bar welded all the way around lip INWARD so the bolts will be hidden.............jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
3 Attachment(s)
More pics-Original look on pass side--how much tub reduced-Floor will look close to this................jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
Looking good! Like the inspiration picture :chevy:
|
Re: 68 aka "Chained in Porterbuilt Prison"
Last truck---something's always give me a burr in my saddle about that pic and I want your opinion--Look at the center 2 boards and tell me it would not look better with a centered bed strip and then run the wide boards all the way out!! I've done the math and it still would look right at the outer edges--I know --I'm anal but it has always bothered me..............jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
question for ya...I had previously thought the inner bedsides didn't need to be cut to clear the tires. So I guess my question is why are you doing what you're doing?LOL!
|
Re: 68 aka "Chained in Porterbuilt Prison"
Good question-gaining 1 1/2 " towards fender-I didn't have 2 but wheel will sit closer to lip and improve overall look-Don't like look if wheel is inset 2 far-Just a personal choice for me-But there is plenty of room without this mod especially with inboard bridge for bags--Check 1st pic and look how I trimmed the fender lip(roll) about 5/8" all the way around-like late model fenders.........Got 2 finish pass side and then off to blaster.......jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
I am totally like you on the width of the boards bothering me... I always planned to install equal sized boards unless I was doing an original restoration (and then it would be painted anyways ;))
|
Re: 68 aka "Chained in Porterbuilt Prison"
Look at that bed pic again-See how I widened tub to overreach the bed strip?? Didn't need that wide but felt it could not fall on strip--changing boards would eliminate this 2!!!..........jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
looking GREAT !!
|
Re: 68 aka "Chained in Porterbuilt Prison"
It's been a while^^^^^ --where U been--Notch cover I suspect?? Love yours but I will leave that labor of love with U--lol-Im not crazy about shorty(depth) bed either but it works for me...let me see the new corner pieces when your done....jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
You nailed it Been working on hinging it. What a pain
Posted via Mobile Device |
Re: 68 aka "Chained in Porterbuilt Prison"
Nice work going on.....subscribed!
|
Re: 68 aka "Chained in Porterbuilt Prison"
2 Attachment(s)
Ok ,before I expose these pics need to acknowledge not my original idea--Va72c10 was way ahead of me-also 67Cheby on his notch cover--------well I was between coats of epoxy today and shaZam---this is done without welds-all panel epoxy-Cut new gate(whew!!!) installed 3 by 3/16 backing metal--flush fit script--now all left is lite body work--(actually started this last nite--epoxy needs 4 hrs min to set).............jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
2 Attachment(s)
Don't know if I have the Kahonnees to cut a real good fender but here is another idea--Looks better in person.............jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
2 Attachment(s)
One more weekend project done...........I have always had a pet-peave about the area under the bedroll-always rusts-cant paint well............ssssoooooo I shave the inside lip and cap the bottom............makes a nice finished look--This will need a little body work on the roll edge to be perfect---another panel bond project-with minimal welding.............jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
That's a great idea, always feel rust in this area.
Posted via Mobile Device |
Re: 68 aka "Chained in Porterbuilt Prison"
I like the bedside mod. And the gate mod is cool! Much more subtle than my original idea :D
|
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
|
Re: 68 aka "Chained in Porterbuilt Prison"
Hey Jim--tailgate looks great. I think the fender would look pretty cool too.
|
Re: 68 aka "Chained in Porterbuilt Prison"
i love the tailgate,great work on the bedsides but , think it might be to much on the fenders ?? just my opinion
|
All times are GMT -4. The time now is 03:41 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com