Re: Tre5 Customs roadster blazer project
Making good progress!
|
Re: Tre5 Customs roadster blazer project
Awesome! Love the flush caps where the stake pocket went
|
Re: Tre5 Customs roadster blazer project
I assume those are not floating calipers if you've run hard line all the way on them?
|
Re: Tre5 Customs roadster blazer project
No, they are floating. I have never had a problem running the hard line straight to a floating caliper. I use stainless steel annealed line, it is more flexible when annealed. The only down fall I see doing it this way is that whenever the owner goes to replace rear pads he will have to disconnect the hard lines and re bleed the brakes... Once every 40,000 miles or so, so really not that big of a deal.
|
Re: Tre5 Customs roadster blazer project
http://i328.photobucket.com/albums/l...405_172350.jpg
http://i328.photobucket.com/albums/l...405_184542.jpg http://i328.photobucket.com/albums/l...405_172343.jpg Got the Grant Customs skin welded up and installed the 15" AVS led tail lights installed. My buddy Will came over and helped out a bit. I had to get a picture of someone other than me working on the truck, so here he is... drilled who knows how many holes in the floor piece. |
Re: Tre5 Customs roadster blazer project
Almost done with the tranny hump. Just one small patch panel on the drivers side to finish up.
http://i328.photobucket.com/albums/l...406_170518.jpg |
Re: Tre5 Customs roadster blazer project
Your metal work look great. I like your rear lights in your tail gate. subscribed
|
Re: Tre5 Customs roadster blazer project
looks good man!
|
Re: Tre5 Customs roadster blazer project
clean....as usual
|
Re: Tre5 Customs roadster blazer project
:jdp:Holy Fabrication! this is amazing. subbed
|
Re: Tre5 Customs roadster blazer project
ok, finally back to work on the blazer. I got the 1" narrower Porterbuilt arms on and the hood now closes.
The standard arms from them were a bit too wide for the 24's to fit under the hood. With them now 1" narrower the tires clear the roll in the hood. I also got the Porterbuilt hood hinges on and all the front end mounted up. Now I just need to add some support in the fenders as well as a place to hide wires up underneath the fender support. Then weld up the front Grant Customs roll pan and fill all the little holes in the hood, grill, and fenders. http://i328.photobucket.com/albums/l...-00-46_734.jpg Please note that you must be a supporting member to post classified items. This includes but is not limited to What Its Worth, Want To Buy, Want To Trade, and For Sale. Please consider supporting the forum by subscribing. Further information on the subscription levels available are located here If you need any further assistance with that please contact any Admin for help. |
Re: Tre5 Customs roadster blazer project
great build.
|
Re: Tre5 Customs roadster blazer project
nice work kat!!
|
Re: Tre5 Customs roadster blazer project
First time it has been out of the garage!
http://i328.photobucket.com/albums/l...-51-06_748.jpg http://i328.photobucket.com/albums/l...-52-38_716.jpg http://i328.photobucket.com/albums/l...7-52-59_62.jpg http://i328.photobucket.com/albums/l...-56-39_427.jpg Does the windshield need to be laid back? |
Re: Tre5 Customs roadster blazer project
I like what I see, next time you're in So.Cali bring it out :c2:
We would Love to see it up close and in person |
Re: Tre5 Customs roadster blazer project
looking good!!!
|
Re: Tre5 Customs roadster blazer project
Its coming along nice!
|
Re: Tre5 Customs roadster blazer project
very cool , again nice work!!
|
Re: Tre5 Customs roadster blazer project
could you set something across the top of the fenders and tell me how much your tires stick up above the top of the fenders, if you dont have time that is fine but if you do it would be a good little bit of research for me
|
Re: Tre5 Customs roadster blazer project
Quote:
|
Re: Tre5 Customs roadster blazer project
Quote:
|
Re: Tre5 Customs roadster blazer project
Quote:
|
Re: Tre5 Customs roadster blazer project
Quote:
|
Re: Tre5 Customs roadster blazer project
IMO:lay it back to match the angle on the hood...
|
All times are GMT -4. The time now is 11:48 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com