![]() |
Re: LT1 GenV swap
That filter looks like a great option for the LT but I checked the WIX filter on rock auto, part number 33814. This lists out all 3 ports on the filter as 5/16. Hope that is a typo, because otherwise I not see how that would be good as the fuel pump inlet is 3/8
|
Re: LT1 GenV swap
Do you have any more of the water pump adapters?
|
Re: LT1 GenV swap
Quote:
|
Re: LT1 GenV swap
Following along. I just picked up a L83/6L80 for my K10. I'm with you on the accessory brackets, either they are WAY too expensive or ugly. I'm deleting the vacuum pump as I already have hydroboost installed.
Red |
Re: LT1 GenV swap
Good info
|
Re: LT1 GenV swap
Do you have a part number or place where I can find the Fuel pump controller connector?
Red |
Re: LT1 GenV swap
Quote:
|
Re: LT1 GenV swap
I would be interested in the Module, pressure sensor, the connectors and seals and terminals. Possibly the E85 sensor. PM me please.
Red |
Re: LT1 GenV swap
Like to round up some cash for the holley oil pan.. lt waterpump adapters 125 shipped.
Please pm me if interested. Thanks |
Re: LT1 GenV swap
Thanks 87chevy.com!
Great read and loads of info. I'm putting an L83/6L80 in my '82 Stepside. It is great to find all this info here! How is everything with your truck? Any news? Thanks again! P.S.: And by "I'm putting...". I mean. I am having it done! I don't have the skills, knowledge, tools or a place in which to do it... maybe some day :) |
Re: LT1 GenV swap
Going to offer the extra connectors I have for sale. Each connector comes with the required terminals, and seals with an extra terminal as a backup.
These are the only ones you need to get the L83 up and running aside from modding the engine harness. Fuel pump driver module , fuel pump, e85 sensor, fuel pressure, throttle pedal and obd 2 port. If there are more than a few interested, I can order more and subscribe and become a member and support the board once again. Thanks, Clint |
Re: LT1 GenV swap
Got a question for the mass' out there... is this a fuel regulator or fuel damper
https://imagizer.imageshack.com/img923/3081/LOHaoM.jpg https://imagizer.imageshack.com/img924/6659/yG0IYx.jpg https://imagizer.imageshack.com/img924/350/wOnzBX.jpg From the filters with regulators in them, this looks like it would be a regulator since the silver container, fuel filter, has an inlet from the pump, and 2 outs.... one to the top of the lid, and the other to this regulator/dampner... but has an outlet to drain right back into the bucket. If it has the fuel pump control module to pwm the pressure, is this a backup / fail-safe? Clint |
Re: LT1 GenV swap
I read somewhere that it has a pressure relief valve in the stock pumps. When you shut the engine down it relieves the pressure on the pump.
Red |
Re: LT1 GenV swap
Most of the pictures that look like the part in question is a regulator... a dampner only has the the center inlet... wonder if gmperformance would know. I still plan on running factory pump assembly.. just haven't made progress on the rings...
|
Re: LT1 GenV swap
And more searching revealed the ecu terminals, and most of the connector terminals in the harness.. gonna repair the one the first junk yard nipped off 2 sensors and make it good as new without splices and maybe just run that harness and sell the other harness that's not been damaged.
|
Re: LT1 GenV swap
How deep are you in the wiring? I'm trying to figure out the canbus. As far as I can tell there are 2 circuits needed, 1 for the FPCM and 1 for the trans. Sound right?
Red |
Re: LT1 GenV swap
Quote:
|
Re: LT1 GenV swap
Sweet that the way I was gonna wire it. Did you put a resistor in it? Also, the brake pedal switch, are you using the 4 pin switch?
Red |
Re: LT1 GenV swap
Quote:
|
Re: LT1 GenV swap
Holley pulled a nice one, got an email saying my oil pan has shipped.. got it today.. now I need to pick up the hoist again..
Clint |
Re: LT1 GenV swap
Quote:
I am happy for you don't get me wrong but geeze its been almost two months..... |
Re: LT1 GenV swap
Looks like I should have my pan soon. Being a shop we ordered
My pan through a distributor. Sounds like they have had the pan for some time and it took us calling then to get the order rolling again.... hope to see the pan sometime next week... |
Re: LT1 GenV swap
Glad to hear. Got around to the alternator bracket.. going to give this a try. Should work as there are other companies that offer setups like this
https://imagizer.imageshack.com/img924/2498/1GJ6nL.jpg And keeps the vacuum pump... just need to reinstall it as i was testing out another bracket idea. Need to remake the power steering brackets to incorporate an idler instead of a tensioner... Clint |
Re: LT1 GenV swap
1 Attachment(s)
Got my pan in last week too. Clearance is perfect for my Porterbuilt suspension. Just waiting on Holley's LT accessory drive now. Looks like a couple more months.
|
Re: LT1 GenV swap
Looks great. I have been very interested in doing an LT4 swap for my build as of late, but was initially put off by the cost of getting the front drive system setup. Looks like Holley and Dirty dingo are working on kits or have them already. Dingo said probably another few months for the LT4 stuff.
I'm assuming I'd need to run the Holley pan to clear my crossmember in the 66, since it's actually from an 85 pickup as well? Ever figure out how you'll get a tach signal and coolant temp from? I'd hate to have to rebuy gauges that pull from an OBD port since I have new speedhuts sitting in a box . . . |
All times are GMT -4. The time now is 09:43 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com