![]() |
Re: 1978 Russet Metallic 4x4
.
. Awesome job w/ this one - looks really sharp! Think your Dad will drive it a lot again, or will it see limited use? . . |
Re: 1978 Russet Metallic 4x4
Not sure, but if he doesn't, this guy will.
|
Re: 1978 Russet Metallic 4x4
Quote:
. :metal: :metal: That interior and front end accessories look great! . . |
Re: 1978 Russet Metallic 4x4
Quote:
|
Re: 1978 Russet Metallic 4x4
Dad had only one complaint. The sloppy steering from the original rag joint. So Tuesday I installed a Borgeson unit with u-joints at both ends. Nice upgrade. Ended up sawing the original in half to get it out. I had to cut 8" off the Borgeson unit to get it to fit right. And it was damn hot outside.
Here are me and the boys heading to a car show a couple weeks back. We're not very cool. http://67-72chevytrucks.com/gallery/...0-1600x900.jpg |
Re: 1978 Russet Metallic 4x4
Quote:
http://www.americanfloormats.com/pyramid-rubber-mats/ |
Re: 1978 Russet Metallic 4x4
That's a great picture!
|
Re: 1978 Russet Metallic 4x4
Quote:
|
Re: 1978 Russet Metallic 4x4
Quote:
|
Re: 1978 Russet Metallic 4x4
The rubber grommet is just to seal the housing where the post goes into the base. There should be a friction sleeve wrapped around the mirror post where it clamps into the base. I'll see if I can find a picture from when I rebuilt and painted mine.
|
Re: 1978 Russet Metallic 4x4
John: I know, that's what we're talking about. There just doesn't seem to be enough friction at those surfaces to matter, even tightened. I added several layers of rubber and it would still rotate.
|
Re: 1978 Russet Metallic 4x4
10-4. Mine did the same thing, they were original to the truck though. When I had them apart to paint them, I soaked the base gaskets, grommets and sleeves in hot water and Dawn dish soap then cleaned them. They stay put now. If yours are new, dirt probably isn't the issue - maybe take the sleeves off and tape some skateboard tape in place instead? That should grip good.
|
Re: 1978 Russet Metallic 4x4
Here's the Borgeson shaft:
http://67-72chevytrucks.com/gallery/...-1024x1820.jpg Packing stuff out at the lake: http://67-72chevytrucks.com/gallery/...6-1600x900.jpg |
Re: 1978 Russet Metallic 4x4
Quote:
You can remove the screw at the bottom of the cover over the base of the mirror, and slide the cover up over the rod closer to the mirror head and there are 2 bolts you can access under the cover the gently tighten down on those, test the mirror head to make sure you can still move it. Then just slide the cover back down over the mounting hardware and replace the screw. |
Re: 1978 Russet Metallic 4x4
Lol. Folks, even when you tighten, they still creep. I drive this thing at 80 on interstate. Those big Dumbo's move.
|
Re: 1978 Russet Metallic 4x4
Quote:
BTW, that is THE nicest Blazer I think I have ever seen!! Great job! I just LOVE that interior, sweet! |
Re: 1978 Russet Metallic 4x4
Quote:
|
Re: 1978 Russet Metallic 4x4
Quote:
What I did was take mine apart, and then transfer the GM rubber, and the GM base plate over to my LMC mirrors. They now work fantastic and do not move at all on their own! I will post a few pictures over in my blazer thread, but I couldn't be happier with the results. It seemed like the rubber that GM used was a completely different product. It was also about 1/2 the size of the LMC rubber which was surprising. The GM base plates also fit the shaft much better and have more of a "wrap" on the mirror stem. Phillip |
Re: 1978 Russet Metallic 4x4
Glad you got it figured out.
|
Re: 1978 Russet Metallic 4x4
Are you running r12 or r134a?
|
Re: 1978 Russet Metallic 4x4
Quote:
|
Re: 1978 Russet Metallic 4x4
Quote:
|
Re: 1978 Russet Metallic 4x4
|
Re: 1978 Russet Metallic 4x4
Love this blazer. I hope to see it around town one day...
|
Re: 1978 Russet Metallic 4x4
Quote:
|
All times are GMT -4. The time now is 02:07 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com