![]() |
Re: The Snortin' bull
2 Attachment(s)
Exhuast need's to be run off the shorty block hugger header's before I start the engine. Gettin there . Check list to move the truck on it's own down to few item's.
|
Re: The Snortin' bull
2 Attachment(s)
a little frame webbing insulation for the bed wood to lay on bed cross rail's.
|
Re: The Snortin' bull
Getting closer and closer every update.
|
Re: The Snortin' bull
It's funny, I'd never see a hubcap like yours till I saw this thread. Then 4 of these showed up for sale locally, still in the factory boxes, never installed. 1955 though, you said yours were 1960?
http://bsdwolf.com/hub.JPG |
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
naloc, check your private message folder.
|
Re: The Snortin' bull
2 Attachment(s)
I did manage to get a bit of time in this weekend on the Bull .Not much Thuough, got the exhaust started .The first foot of the down tube's.
|
Re: The Snortin' bull
1 Attachment(s)
Piece by piece.Fab up exhaust front to back. This is alway's time consuming.There are very talented exhaust builder's out there though on my home garage floor I am not one of them.Especially on a bagged truck.
|
Re: The Snortin' bull
1 Attachment(s)
Right side exhaust together to midpoint of truck.
|
Re: The Snortin' bull
1 Attachment(s)
one last underhood install the detent cable bracket for the transmission tv cable.
|
Re: The Snortin' bull
Amazing looking work here.
Every hour you get is progress. |
Re: The Snortin' bull
2 Attachment(s)
Got the lh and rh front exhaust pipe's done and hung.The goal is tuck up high and muffler's to the rear past the cab floor .
|
Re: The Snortin' bull
1 Attachment(s)
This is hour's into pipe's finally a muffler .More pipe to fab.to come.
|
Re: The Snortin' bull
2 Attachment(s)
The easy way out build a couple of stack's up thru bed floor.Just playin' around.Fab'd pipe's to flow out to side's to follow kickup and to rear of bed into corner's to dump.
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
3 Attachment(s)
Just layin' some more pipe. I know these picture's are kinda boring though I have found that in the forum's we pick up subtle little helpful thing's in the picture's. Just need to trim and fit and finish off the tailpipe's. Install header flange to pipe gasket's maybe tip's and exhaust is done.
|
Re: The Snortin' bull
Looking good, nice progress.
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
3 Attachment(s)
rear pipe's together from mufflers back to rear behind bumper area.
|
Re: The Snortin' bull
3 Attachment(s)
Exhuast is all in and hung.Used Remflex gaskets at headers , pipe is 2.25" aluminized steel.Mufflers are Jones Exhuast.Moved suspension thru far and lowest position no interference.Front down pipes get close to the ground when aired down though.Might to redo those in future.
|
Re: The Snortin' bull
1 Attachment(s)
Went to fire the truck up today.Chased some leak's around though one at the carb would not stop. Got a little to gorilla like with this fitting.My day was done. For now.
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Like your pipe work.
Looking great. I am looking forward to when I can eventually build my pipes. |
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
1 Attachment(s)
Repaired the fuel feed into BG Demon carb. Ready again.
|
Re: The Snortin' bull
Nice. Time to get it on the road.
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
2 Attachment(s)
Fully aired down. The truck was planned out to be able to cruise at full aired out. I did not build it to lay frame but to almost appear to and still slow cruise in show atmosphere. The pinch welds are just over an inch off the ground under the cab rocker's.
|
Re: The Snortin' bull
1 Attachment(s)
a bit of an engine starting tool kit ready to go.
|
Re: The Snortin' bull
2 Attachment(s)
So like a lot of the forum member's have said life get's in the way 2 week's go by with gas in the tank and key's in the cylinder. Today I started the GMC up .Broke in the cam and etc.Drove down the drive way a couple time's .Got a couple of video's though need a "golden" token from admin to post?
still got work to do. |
Re: The Snortin' bull
:metal: truck is looking good.
|
Re: The Snortin' bull
Truck looks great.
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
1 Attachment(s)
GMC, The Bull is out in the weather now.Put in the final door surround weatherstrip on the cab.Sill plate's also.
|
Re: The Snortin' bull
1 Attachment(s)
I am on the fence to put on a rear bumper or not. Even though the exhaust tip's are hardly showing I still tipped off with a chrome pencil tip. Yosemite Sam street sweeper's I call them.
|
Re: The Snortin' bull
Wow, looking really good.
My vote is for a bumper, always. |
Re: The Snortin' bull
Looks great. I enjoyed reading your build. I like your style, dig those hubcaps!
|
Re: The Snortin' bull
A link to Video of truck on the driveway . https://vimeo.com/156134915
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Quote:
|
All times are GMT -4. The time now is 04:28 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com