![]() |
Re: Sarge's rattle-can rebuild
If you don't have one already there are body files to shave the filler down before it completely sets. Makes shaping a bit easier.
|
Re: Sarge's rattle-can rebuild
Quote:
Quote:
|
Re: Sarge's rattle-can rebuild
3 Attachment(s)
Getting close. I picked up a small piece of 16 gauge steel from Home Depot to cut some patches out of. I was guessing the size needed and it turned out to be thicker than the damaged area. I used it anyway, can't see what it'd hurt. It probably kept me from blowing through more times than I did. Passenger side a-pillar first. It has one hold I need to tack.
|
Re: Sarge's rattle-can rebuild
4 Attachment(s)
This other area is in the drivers side cowl area. Is it just me, or does this rust hole look like a face that's laughing? Rust removed, patch cut, then tacked in. I think I was holding the trigger too long. It was late yesterday when I did this one and when I ground these smooth and went to make another pass around I blew through twice. I don't like chasing mistakes when I'm tired so I put my toys up for the day. I'll get back after it today and hopefully finish the repairs and prime/paint.
|
Re: Sarge's rattle-can rebuild
Nice job, one less worry.
|
Re: Sarge's rattle-can rebuild
Quote:
|
Re: Sarge's rattle-can rebuild
What'd you use to make such a precise cut - dremel?
|
Re: Sarge's rattle-can rebuild
1 Attachment(s)
Quote:
|
Re: Sarge's rattle-can rebuild
4 Attachment(s)
Finishing up this repair, after welding in some patches and grinding the welds smooth I wiped some bondo over both spots to help smooth out the repair. Also, I had two other spots where the metal was solid but rust pitted. There wasn't any point cutting them out but I did want to stop the rust and repair the area best I could, so I treated them with rust converter and let them cure then wiped over them with bondo as well. Then the entire glass channel got sanded, primed, and painted.
|
Re: Sarge's rattle-can rebuild
3 Attachment(s)
Real, real happy with the way this turned out. Whoever said I'd rather be lucky than good said a mouthful. The new windshield should be installed today.
|
Re: Sarge's rattle-can rebuild
Like it never happened!
|
Re: Sarge's rattle-can rebuild
Thanks Art. I'm going to try my luck on the floorpans next, I've got three or four smallish rusty spots that need to be cut out and patched. The steel seems to be thicker there so hopefully it's a little more forgiving.
|
Re: Sarge's rattle-can rebuild
Nice work man. That turned out great.
|
Re: Sarge's rattle-can rebuild
Thanks Marcus. I thought I'd have the windshield in by now for the last repair pic but the guy is MIA. I'm ready to drive this thing again.
|
Re: Sarge's rattle-can rebuild
nice work man!
|
Re: Sarge's rattle-can rebuild
Thanks DJ. It's slowly coming around.
|
Re: Sarge's rattle-can rebuild
2 Attachment(s)
I just finished this. Not too bad coming out of a rattle can
|
Re: Sarge's rattle-can rebuild
Quote:
|
Re: Sarge's rattle-can rebuild
Hey John. i just glanced over your thread and something came to mind. I'm not sure if you know this or not, but that military green paint is a carcinogen. Be extremely careful when sanding that stuff, and wear a HIGH quality respirator. Just fyi.
Nice work on the truck! Mike |
Re: Sarge's rattle-can rebuild
Thanks Mike. I'd read that stuff was terrible bad but I still don't have a good respirator, I'm still shopping for one. I folded a scott's shop towel in half and put it over my mouth and nose with a cheapie dust mask over it and kept a compressed air nozzle at my side to keep the stuff blown away from me. I know that's not a good substitute, but it's what I had. I tried to stay away from the stuff.
I mentioned to you recently your old truck pops up on CL constantly, and I saw it again the other day. This time it's not for sale but it's parked next to a truck that is. That thing is like Waldo. Check out the ad, 2nd pic: http://montgomery.craigslist.org/cto/5577218861.html |
Re: Sarge's rattle-can rebuild
Good eye! That's funny that you keep seeing it.
|
Re: Sarge's rattle-can rebuild
Quote:
|
Re: Sarge's rattle-can rebuild
I like it too. It's got the right amount of gloss to look like it might have been or could have been factory. Did you use it on your frame too?
|
Re: Sarge's rattle-can rebuild
Lookin good John! Keep at it! :metal:
|
Re: Sarge's rattle-can rebuild
Quote:
|
Re: Sarge's rattle-can rebuild
Quote:
Quote:
|
Re: Sarge's rattle-can rebuild
1 Attachment(s)
Quote:
|
Re: Sarge's rattle-can rebuild
4 Attachment(s)
This may be one of my favorite Blazer projects yet. I've never had a good place for the top. The main criteria was out of the way, whether I'm using the top or not. This was simple and worked great. Big thanks to made2drag for stopping by and helping me get if off the truck and on the rack.
|
Re: Sarge's rattle-can rebuild
Bud that worked out great.
|
Re: Sarge's rattle-can rebuild
Thanks Jim. Added bonus there was no rust under the top. I was a little worried about that after finding some under the windshield gasket.
|
Re: Sarge's rattle-can rebuild
Alright now enjoy going topless! It's beautiful over here.
|
Re: Sarge's rattle-can rebuild
Good build. I like the, learn as you go, method. I look forward to doing that with welding at some point too. I also grabbed some hammers and dollies to start tapping out little dents. Completely understand your comment about reverse dents. Did you get some good summer use of of this rig?
|
Re: Sarge's rattle-can rebuild
1 Attachment(s)
Quote:
|
Re: Sarge's rattle-can rebuild
updates?
|
Re: Sarge's rattle-can rebuild
Quote:
I'd planned to finish this truck this year but that probably won't happen now. I've got a new engine for my other K5 that has been sitting in my shop a few years now, I'll get that one running again so at least both trucks are driving. Too many projects... |
Re: Sarge's rattle-can rebuild
Quote:
|
Re: Sarge's rattle-can rebuild
truck is really cool glad to hear she will get some attention she deserves it! lol
|
Re: Sarge's rattle-can rebuild
Quote:
Quote:
|
Re: Sarge's rattle-can rebuild
Quote:
|
Re: Sarge's rattle-can rebuild
Quote:
|
All times are GMT -4. The time now is 10:57 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com