The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   Squarebody Projects and Builds (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=139)
-   -   Minnesota Daily Driver (https://67-72chevytrucks.com/vboard/showthread.php?t=643968)

400/400 04-27-2020 06:26 PM

Re: Minnesota Daily Driver
 
Quote:

Originally Posted by MTCK (Post 8727014)
Truck looks great! Time to drive her more with the cheap gas!

Thanks. It’s definitely nice filling the tanks at $1 something a gallon.

400/400 05-03-2020 05:31 PM

Re: Minnesota Daily Driver
 
1 Attachment(s)
Finally installed my ORD HD front shackles. Luckily all the hardware cooperated. The frame side bushings were definitely shot.

400/400 05-03-2020 05:40 PM

Re: Minnesota Daily Driver
 
1 Attachment(s)
Thinking about changing up the front end again. I need a front receiver for my winch and want to make a jib pole. Easiest way to mount that I can figure is off the plow frame I took off.

I never liked how the frame pushed the factory bumper out. It never looked quite right. I’ve got an old piece of c-channel that happens to be the right width I’m looking at using for a bumper. I can also mount my receiver to it and some shackles.

400/400 05-03-2020 05:42 PM

Re: Minnesota Daily Driver
 
1 Attachment(s)
I made a mini jib pole for the rear. It comes in handy.

MTCK 05-03-2020 05:45 PM

Re: Minnesota Daily Driver
 
Bumper will look tough. I also hate how this vintage Meyer mount shoves the bumper out. My plow will actually contact the bumper if I’m pushing snow with it hard over. Might be worth checking clearance on that channel.

400/400 05-03-2020 05:55 PM

Re: Minnesota Daily Driver
 
Quote:

Originally Posted by MTCK (Post 8731469)
Bumper will look tough. I also hate how this vintage Meyer mount shoves the bumper out. My plow will actually contact the bumper if I’m pushing snow with it hard over. Might be worth checking clearance on that channel.

Good point. Mine had hit the bumper too at stock height based on the paint marks on the old bumper. I never had a problem with it after the 4” lift.

I’ll have to check the clearance. I could probably chamfer the bottom corners of the channel if needed.

400/400 05-26-2020 06:27 PM

Re: Minnesota Daily Driver
 
1 Attachment(s)
Bumper installed.

400/400 05-26-2020 06:28 PM

Re: Minnesota Daily Driver
 
1 Attachment(s)
With the winch.

400/400 10-25-2020 06:28 PM

Re: Minnesota Daily Driver
 
1 Attachment(s)
Not a lot new. Just been using as a second truck.

Decided to change up the steps.

MTCK 10-25-2020 07:01 PM

Re: Minnesota Daily Driver
 
Looks good do they bolt to the pinch weld or the frame?

400/400 10-25-2020 07:30 PM

Re: Minnesota Daily Driver
 
They mount to the front cab mounts and by the rear spring hanger to the frame.

Good thing I took care of the body mounts earlier this year.

400/400 03-18-2021 06:47 PM

Re: Minnesota Daily Driver
 
1 Attachment(s)
Out of hibernation. 1st drive of the year.

calvin78612 03-19-2021 08:26 AM

Re: Minnesota Daily Driver
 
What did you do with the old step bars ?

400/400 03-19-2021 07:49 PM

Re: Minnesota Daily Driver
 
Quote:

Originally Posted by calvin78612 (Post 8896452)
What did you do with the old step bars ?

Got ‘em stored away. Have a couple more squares I could use them on.

They seems to multiply...

LT7A 03-23-2021 02:00 PM

Re: Minnesota Daily Driver
 
So funny, thought it was black until the last picture in the sun. Like it with a canopy on there.

I went back through your thread and realized that you initially got this truck just for the plow. And then with the work you and your dad put into it, it's turned into a really nice rig.

400/400 03-23-2021 05:02 PM

Re: Minnesota Daily Driver
 
Quote:

Originally Posted by LT7A (Post 8898311)
So funny, thought it was black until the last picture in the sun. Like it with a canopy on there.

I went back through your thread and realized that you initially got this truck just for the plow. And then with the work you and your dad put into it, it's turned into a really nice rig.

Yeah, the Indian bronze metallic pops in the sun.

Thanks! Never anticipated how far the build would go when I got it.

photo-tom 03-26-2021 11:29 AM

Re: Minnesota Daily Driver
 
Hell of a lot of elbow grease. Cheers from a fellow Indian Bronze Minnesotan.

400/400 11-07-2021 07:00 PM

Re: Minnesota Daily Driver
 
1 Attachment(s)
Always fun doing truck stuff. It’s that time again to store the toon for the season. Used the front hitch to move it into the shed.

400/400 09-21-2023 09:54 PM

Re: Minnesota Daily Driver
 
2 Attachment(s)
Wow haven’t updated in a while. Changed up my steps into something more HD.

Using her once again to pull the boat for the season.

LT7A 09-23-2023 07:43 PM

Re: Minnesota Daily Driver
 
Looks good, nice setup!

400/400 09-26-2023 07:49 PM

Re: Minnesota Daily Driver
 
1 Attachment(s)
Quote:

Originally Posted by LT7A (Post 9243861)
Looks good, nice setup!

Thanks!

Got out in the woods with the dog and pickup.

400/400 04-24-2024 05:33 PM

Re: Minnesota Daily Driver
 
1 Attachment(s)
Got her out of hibernation. Pulled the topper off for the summer and got some new rubber.

Darkrider 05-16-2024 01:41 PM

Re: Minnesota Daily Driver
 
This truck has def undergone quite the transformation!

400/400 05-17-2024 07:22 PM

Re: Minnesota Daily Driver
 
Quote:

Originally Posted by Darkrider (Post 9312686)
This truck has def undergone quite the transformation!

That’s for sure. Just realized I’ve had it for 15 years and it’s been a decade since it was painted.

400/400 05-17-2024 07:24 PM

Re: Minnesota Daily Driver
 
1 Attachment(s)
Working in the garden. Hauling dirt.

400/400 05-17-2024 07:25 PM

Re: Minnesota Daily Driver
 
1 Attachment(s)
-Attachment 2362363


All times are GMT -4. The time now is 12:41 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com