Re: Project Vitamin C-10
 

How many projects you have going??? My Son is about to bust, his truck is so close to being done but there are a few little details keeping us from finishing it now. How do you like your plasma cutter? I have been thinking about asking for one for Christmas. Looking forward to seeing more pictures of the trucks.

JRBECK64

Re: My 1965 build thread
 

I hate flaring took a few tries for me as well when I added the disk brakes to my 66. Thanksfully the guy at the parts house gave me an extra 2' section to practice on!

Re: My 1965 build thread
 

:metal: Since I work at f*rd I better drive one. ;)

Your right. I had a vision of cleaning up around here. :lol:

No, but have a complete cab with a good roof for $150

Yes, and I love that thing.

Got the 65 & 55 and a long honey do list. :lol: Ya'll are doing a great job on your sons truck. If you do alot of metal work the plasma is awesome.

I haven't tried SS yet. Did you run steel lines?

Re: Project Vitamin C-10
 

My plasma cutter took a sh*t a couple of years ago. It needs a circuit board that cost about $500. Not worth fixing it even though it's a $3,200, 20 year old one from Snap-on. The newer ones are now much smaller, and I can get one for about $800. If I need one that bad I could use borrow my sons. When I had my business I used it all the time. :waah:

Re: Project Vitamin C-10
 

Finally getting back on it. Decided to work on the hood. I cut the problem areas out so the sand blaster can get to the inside of the corners.

The right corner was the worst of the two sides.

http://i606.photobucket.com/albums/t...d/DSC01712.jpg

http://i606.photobucket.com/albums/t...d/DSC01714.jpg

I'm holding a chunk of filler that was packed in the corner.

http://i606.photobucket.com/albums/t...d/DSC01718.jpg

http://i606.photobucket.com/albums/t...d/DSC01720.jpg

This is the Left side.

http://i606.photobucket.com/albums/t...d/DSC01713.jpg

http://i606.photobucket.com/albums/t...d/DSC01715.jpg

It only had pin holes. I will clean the rust and weld the holds and reinstall.

http://i606.photobucket.com/albums/t...d/DSC01725.jpg

http://i606.photobucket.com/albums/t...d/DSC01726.jpg

I'm going to use extra cowl side panels to cut out patches. The contour is already there. Since I couldn't give them away I figured why not put them to good use. They can also be used to repair door check strap damage.

http://i606.photobucket.com/albums/t...d/DSC01717.jpg

I have an extra hood that isn't any good on the outside, but has a good inner structure. I'll cut patches out of it to repair the bad areas.

http://i606.photobucket.com/albums/t...d/DSC01722.jpg

Re: Project Vitamin C-10
 

good idea alan :metal:

Re: Project Vitamin C-10
 

Hey Alan,

I just read you build thread and realized that you threw away a few items, I too have some things that I cant sell either so I know what you mean it hurts when you have to get rid of something that some one can use.

thins are looking great btw

Re: Project Vitamin C-10
 

Thanks, I have a smart moment every now and then. :haha:

Thanks Kevin.:metal:

Re: Project Vitamin C-10
 

hey alan the pics of your hood got me thinking
i want to build my own fiberglass hood and use the inside steel bracing from the stock hood
i dont know if it would work but i think it would be better than a aftermarket one
what do you think

Re: Project Vitamin C-10
 

Gage if you do it and it works nice, build me one too.

Alan have you heard or used the cunifer brake lines before?

Re: Project Vitamin C-10
 

I don't know alot about fiberglass, but I'm sure what ever you do would be better than what is on the market. Keep in mind the hood springs are designed for a heavy hood. I've seen people add links of chain to the spring to reduce the stress on the hood. There's got to be a better way than using links of chain.

Someone else has mentioned that type of brake line in this thread. To answer your question, no I haven't messed with them at all. I might try them someday. For this one I will be using SS. I might regret it. Thanks

Re: Project Vitamin C-10
 

[QUOTE=Alan's Classic;3588459]I don't know alot about fiberglass, but I'm sure what ever you do would be better than what is on the market. Keep in mind the hood springs are designed for a heavy hood. I've seen people add links of chain to the spring to reduce the stress on the hood. There's got to be a better way than using links of chain.

i was going to use shocks

Re: Project Vitamin C-10
 

I was just asking, cuz I'm getting all my brake lines for free, and it's the cunifer. I know Audi, Volvo, and some other builders use it. Here is a link from where I'm getting it from www.fedhillusa.com

Re: Project Vitamin C-10
 

Nice!!

Thanks for the link. That looks like a nice product.

Re: Project Vitamin C-10
 

Wow! It has taken me about a month of pretty regular reading to get to this point. Awesome build Alan!!! This should be a must read for anyone that is going to do a full frame off resto. It really goes to show that a project of this magnitude becomes part of your life and yet there is a lot of life going on around our builds and there isn't always time to work on our trucks. Also it's crazy that just reading these build threads makes me feel like I know a lot of you guys. It is so easy to get sucked into this site because it's more than just nuts and bolts in these threads, there's a lot of blood, sweat, and tears. Kudos to all of you and especially Alan for the great reading and all the valuable tips and information!

Re: Project Vitamin C-10
 

Check out this forum for fiberglass stuff. http://www.fiberglassforums.com/ There is some really cool work being done. And if you want to see some really over the top work read this thread. http://www.fiberglassforums.com/showthread.php?t=5267 If I remember correctly you need to join to see the images.

Re: Project Vitamin C-10
 

thanks i just joined now im waiting to be approved

Re: Project Vitamin C-10
 

:agree: :metal:

Re: Project Vitamin C-10
 

Thanks for the compliments with the well written post. It keeps me motivated knowing what I do either right or wrong helps people.

Nice links.

Got the Mar-K inner bedside patches installed on one bedside plus I also did a couple other patches. The patches were great and are one of the easiest patch panels you will ever do.

Did some measuring to determine where to make my cut and got the patch clamped in place.

http://i606.photobucket.com/albums/t...d/DSC01745.jpg

Installed the wheel house to make sure everything is lined up. With it clamped in place will help hold everything in place.

http://i606.photobucket.com/albums/t...d/DSC01746.jpg

http://i606.photobucket.com/albums/t...d/DSC01747.jpg

Completed

http://i606.photobucket.com/albums/t...d/DSC01748.jpg

Had to make and replace the short angle. I made it out of some good metal that I just cut out for the patch. That way I would have a good square hole to go in the corner. It's hard to get a drill in the corner later when I test fit everything.

http://i606.photobucket.com/albums/t...d/DSC01749.jpg

I used some old metal from a scrap door to make a patch.

http://i606.photobucket.com/albums/t...d/DSC01750.jpg

I reversed the bend.

http://i606.photobucket.com/albums/t...d/DSC01751.jpg

Held it in place with self tapping screws to create a template.

http://i606.photobucket.com/albums/t...d/DSC01754.jpg

Getting it lined up.

http://i606.photobucket.com/albums/t...d/DSC01755.jpg

I knotched mine here. Others will do it differently, but worked well for me. There was too much going on in one location. The lap, corner and bolt hole were all too close together. I chose to space things out a little. There is a lower bolt hole to use for alignment.

http://i606.photobucket.com/albums/t...d/DSC01757.jpg

more on next post

Re: Project Vitamin C-10
 

http://i606.photobucket.com/albums/t...d/DSC01763.jpg

Done welding just need to grind.

http://i606.photobucket.com/albums/t...d/DSC01764.jpg

Re: Project Vitamin C-10
 

Nice work Alan! I have a couple panels to patch i will just send them on over since you already have your tools out and warmed up ;) :lol:

Re: Project Vitamin C-10
 

and of course it looks perfect
alan you make this look so easy:metal:

Re: Project Vitamin C-10
 

Very nice.:metal:

Re: Project Vitamin C-10
 

:haha: I had to knock the rust off of the tools. :lol: It's been a while since I got anything done to it.

Thanks. I always remember my first years as a body man. Still got a lot to learn. ;)

I'm thinking about cutting my own wood for the bed. The only thing I haven't built on this truck is the rearend and trans. I might pay someone to install the windshield just because of the breakage factor. I think it will still classify as home built.;)

Re: Project Vitamin C-10
 

very nice work Alan

Re: Project Vitamin C-10
 

OH, I do not think anyone will argue about yours being homebuilt.

There are somethings that I let the more qualified people in know do for my stuff. Trans work, Engine short block machine work and assembly, rear gear set up, seat upholstery, winsheild install (for the same reason you mentioned)...you know, the things that I don't have the correct tools for...

Looking good, ALAN!

Re: Project Vitamin C-10
 

This is and has been an amazing adventure and undertaking. Thanks for the effort you put into yours. Its helps us all feel that we can do more.

Re: Project Vitamin C-10
 

Hands down, Alan - best build thread so far. Detail is incredible and it's easy to see the care taken in thinking the process out. Thanks again for the effort.

Mac. :mm:

Re: Project Vitamin C-10
 

Great job Allan. You do make it look easy, but we know it's not. :metal:

Re: Project Vitamin C-10
 

I second everyone above, great job, and yes you make it look so easy! Looking back I wish I would have used patch panels myself instead of welding in just an bottom angle but no dineros lol. And as always many thanks for the pictures and write up.

Re: Project Vitamin C-10
 

Thanks David!!

I appreciate it!!. I forgot about the upholstry. Plan is for black leather wrap with orange and black houndstooth inset.

:thumbs:

Thanks Mac!! Yeah, I do have a thinking problem.:lol:

Amen brother!! Patience is a must with doing body work.

:thumbs: No matter your range of experience, there will always be things you wish you should have done differently. I have several things on my mind. There will be more once I get all of the systems working. ;)

I checked on line with homedepot for wood. A 1X8 red oak is $4.10/linear foot. I figured the cost with tax to be around $350. There are only 2 boards of the 10 runs that a 1X6 wood work, so I just figured all 10 runs at 8" wide. I will contact some cabinet shops to see what their cost would be. If there isn't much difference in price why not just buy them pre made, other than just the satisfaction of doing it yourself.

Re: Project Vitamin C-10
 

Yes sir thats what I call progress... Good work man.

Re: Project Vitamin C-10
 

Alan your my hero, when I grow up I wanna be just like you. LOL

Keep it up man I enjoy reading about all your good tips.

Re: Project Vitamin C-10
 

Choose a type of wood that is not available pre-made. Then it makes the decision easy, and the truck more custom. ;)

Re: Project Vitamin C-10
 

:thumbs:

You might want to check with my wife before you say that. She can tell you all of my flaws.:lol:

Great idea. I found Peach State Lumber that has a lot of different kinds of wood. Here is their Web site

Finally got around to cutting up a tree that my dad cut down in the spring. Everyone needs a great neighbor like Shannon. I told him I was splitting wood and he was over in no time. Good thing I hand a rand handed axe. :lol: Had to get an action shot.

http://i606.photobucket.com/albums/t...2/DSC01804.jpg

I found a new sand blaster/powder coater 8 miles from the house. Anyone in the area needs to check him out. He has a great place with great equipment. Custom Powder Worx ask for Ervin @ 404-216-4230. He has a big oven to powder coat frames. Tell him I referred you. I get nothing off of it. I asked him if it would be ok if I put his info here, since he doesn't advertise. He is about 5 miles off exit 27 on I-575.

Re: Project Vitamin C-10
 

Still watching and checking in daily... The 51 and I are looking for a little adventure... Thinking about taking a little ride up when things slow down a bit..(nothing like inviting myself up!)

Keep up the great work, I have learned a lot from your thread..

Re: Project Vitamin C-10
 

I vote for the Bubinga under the exotics. It has some really nice grain. Of course that is without knowing the cost. ;)

At the Texas Classic Car Show in Austin this weekend a guy had an F100 with a Granite bed. It was definitely different. Unfortunately it was in the last row we looked at and everyone was bugging me to leave, so I did not get a photo. :waah:

Re: Project Vitamin C-10
 

GRANITE!!!
that must have been heavy

Re: Project Vitamin C-10
 

http://i606.photobucket.com/albums/t...2/DSC01804.jpg

i need some firewood, i will be up there soon to pickup some shannon. LOL hope all is well up there! Sorry i havent gave ya'll a shout in a while been busy at work.

Re: Project Vitamin C-10
 

Thanks Taylor, invite yourself anytime. ;) Lookin forward to seeing the 51.

I didn't call them today, I hope tomorrow. I'll post up a few prices once I get them.

:agree:

I'm just as guilty for not calling.;)

I forgot to mention before that I left my hood and grill at the sand blaster