Re: What did you do to your truck today part III
1 Attachment(s)
Finally! Got the engine in on the 62. Planning to fire it up on Thursday evening.
|
Re: What did you do to your truck today part III
Quote:
|
Re: What did you do to your truck today part III
5 Attachment(s)
Repaired the pitted and rusted portion of the bed rear cross sill.
|
Re: What did you do to your truck today part III
Replaced Speedo Driven gear, watched needle bounce around and then slowly down to nothing. :(
Rebuilt Rag Joint on steering shaft..... twice. First try Steering wheel was upside down :dohh: Replaced fuel sending unit Float. brass one was cracked. Checked ohms on sending unit and continuity to dash and ground. No movement on guage :banghead: Drank beer and contemplated my mechanical skills :barn: Hooligan |
Re: What did you do to your truck today part III
Love that steering wheel
|
Re: What did you do to your truck today part III
1 Attachment(s)
Scored These Rare commercial Plates I Buddy has Had Them Hanging up For Years
|
Re: What did you do to your truck today part III
1 Attachment(s)
Got The V8 Helping A Buddy Out
|
Re: What did you do to your truck today part III
1 Attachment(s)
Quote:
|
Re: What did you do to your truck today part III
2 Attachment(s)
Got the engine block to cab grounds mounted this morning. I have to remove the heater assembly to get to a hole. I must be getting better as I only smashed one finger.
|
Re: What did you do to your truck today part III
3 Attachment(s)
Making a mess! Pulled motor in hopes to attach and install transmission. Cleaning cab and firewall. Some touch up. Truck was originally Omaha orange but green primer? Keeps popping up on the lower cab.
|
Re: What did you do to your truck today part III
Took the 12 bolt to the welding shop to get the new Captainfab mounting perches welded on and pan hard mount moved over.
|
Re: What did you do to your truck today part III
1 Attachment(s)
Finished the disc brake 5 hole conversion. Cragar's are on and life is good !! lol:flagw:
|
Re: What did you do to your truck today part III
Quote:
|
Re: What did you do to your truck today part III
Quote:
|
Re: What did you do to your truck today part III
2 Attachment(s)
One step closer! McLeod hydraulic bearing installed because the 2466HKR Hooker Competition Headers don't work with stock arm and bellhouse. Had to clearance driver side bellhouse to clear.
|
Re: What did you do to your truck today part III
Well I went and removed and collected a new motor a 350 SBC for my truck today
http://i56.photobucket.com/albums/g1...pscw6zeg3l.jpg http://i56.photobucket.com/albums/g1...ps8uqkokau.jpg http://i56.photobucket.com/albums/g1...psxmfan8qs.jpg |
Re: What did you do to your truck today part III
today I found the left front hubcap for my daily!
they are doing construction on a road I drive on to work, and it was extra rough yesterday. when I got to work I noticed the left front hubcap was missing:( I drove home, scanning the route, but did not see it... but then today I drove even slower, and out of the corner of my eye noticed it next to a fence , laying upside down and full of rain water!! so happy I don't have to bang out and paint up another one! |
Re: What did you do to your truck today part III
:clap: :metal:
|
Re: What did you do to your truck today part III
2 Attachment(s)
Back together! Short of one bolt on motor mount all went smoothly. The fab of the trans crossmember will be tomorrow. Still sitting on stands.
|
Re: What did you do to your truck today part III
Quote:
|
Re: What did you do to your truck today part III
Finally got my steel smoothies to balance after trying 4 sets
|
Re: What did you do to your truck today part III
3 Attachment(s)
I used a Captainfab firewall bracket, CPP all in one master, Wilwood hydraulic clutch cylinder, McLeod hydraulic bearing. The chrome booster came from Tuckers Trucks either s10 or Nova base 7".
The 2466 HKR Hooker Compatition headers didn't work with arm and had to knock down driver side bellhouse to clear flange. This is why th hydraulic bearing over arm. Stock pedal. Big feet can hit all 3 if you try! |
Re: What did you do to your truck today part III
Quote:
So the clutch MC is Wilwood. Model#? Mounting info? Heim joint and pushrod from the pedal connection? |
Re: What did you do to your truck today part III
All the parts came with Captainfab kit. The firewall kit has a spot to drill for Wilwood and all hardware and rods came with kit.
http://www.67-72chevytrucks.com/vboa...d.php?t=362375 http://www.67-72chevytrucks.com/vboa...7&d=1252807174 |
Re: What did you do to your truck today part III
|
All times are GMT -4. The time now is 03:21 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com