Re: 1963 C-10 in NC
 

Ha Ha..
Yea It's going to be 94 tomorrow Bud!
http://ftpcontent4.worldnow.com/wbtv/weather/7day.jpg
I always wanted one of those Gauges..
http://www.wix.com/parklane410/home
http://67-72chevytrucks.com/vboard/s...d.php?t=528409

Re: 1963 C-10 in NC
 

Your cluster looks good.
Greg.

Re: 1963 C-10 in NC
 

I cant wait until fall. Been working day and night to get the truck ready by nov 8. Slowly but surely.

Re: 1963 C-10 in NC
 

Thanks greg. Just dusted it with a paint brush. Light polish on the lens and added a few more lights in the auxilliary plugs. Should be a little brighter. Will try and install tomorrow. Lots of tape will go down.

Re: 1963 C-10 in NC
 

The gauge cluster is...well...:metal::metal::metal::metal::metal:

Re: 1963 C-10 in NC
 

Cluster looks great Jon!

Re: 1963 C-10 in NC
 

Thanks guys......didn't have to do much to it. But figured I'd touch it up while its out.

Re: 1963 C-10 in NC
 

Well, the rain and hail stopped my body prep plans. Did get tons of tape down and cluster hooked up and installed. With no scratches!! Got courtesy light in glovebox run and installed along with new rubber bumpers for the door. Got se sealer down in jams and driverside inner door sanded before dark and muggy.

Re: 1963 C-10 in NC
 

Body to jam sealed

Re: 1963 C-10 in NC
 

Looks fine bud! :chevy:

Re: 1963 C-10 in NC
 

Nice

Re: 1963 C-10 in NC
 

Thanks guys. Still plugging along. Ordered the new engine harness since we went from a 6 to an 8. Will have to lengthen the alternator wires as its on the pass side now. Also got all the window weather stripping enroute.

Re: 1963 C-10 in NC
 

im gonna hold my comments til the paint is dry, but awesome job thus far. u know u close when the gauges go in!!!!

Re: 1963 C-10 in NC
 

Yeah......and was that a brow beater. Tons of tape....knew I'd only get one shot on install without scratches. Some come out easy and some are tight. This is a tight one. My fleetside cluster just pops out. But, no scratches so I was happy!!!!

Hopefully more color this week. Goal is to complete the cab and doors. (just pass door left to figure out. Then back to engine/trans so I can button it back up and bed painted if I get time before my Nov 8 deadline.

Re: 1963 C-10 in NC
 

Window belt line kit came in, door gaskets and the cab gaskets. Will work on stripping doors for paint and get back glass installed this weekend. Calling for alot of rain sat/sun so no paint work.

Re: 1963 C-10 in NC
 

is your flasher on the correct side for a 63'?, just noticed it on the drivers right side...

Re: 1963 C-10 in NC
 

Where its always been as far as I can tell. No other holes under the dash. Ive looked at the factory accessory book and it shows both sides which is kinda confusing. I have the vent cable on the left of the column...so ill leave the flasher on the right.

Re: 1963 C-10 in NC
 

Almost ready for final wet sand on cab. Little more glaze left to do. Door came out great but alot of work. Back glass installed this morning and should be ready for cab paint next weekend. Still need to disassemble door and prep pass door.
Also pic of tank and back cab undercoated from last week. Had it covered due to no back glass.

Re: 1963 C-10 in NC
 

Your dash looks awesome nice job.

Re: 1963 C-10 in NC
 

Looking perrty! :chevy:

Re: 1963 C-10 in NC
 

Man that dash looks nice!

Re: 1963 C-10 in NC
 

Thanks!!!!

Re: 1963 C-10 in NC
 

Thanks TJ!!!

Re: 1963 C-10 in NC
 

Thanks Mark. Was a night shot with flash....so a little dark.

Re: 1963 C-10 in NC
 

Couple of pics that kept turning sideways when I tried to load from the phone. Back cab prep and interior back cab done