Re: PO has me PO'd
Glad that they work for you! If you've sent out free parts, you just paid back a little.
|
Re: PO has me PO'd
http://farm6.staticflickr.com/5516/9...5083fd17_c.jpg
20130721_101336 by jarosaj, on Flickr Hammer and chisel to start hole, then tin snips. After neck was off tank, blow torch and 7/16" wrench. Hold neck horizonal and let gravity help by flowing old solder away. Repop tank has smaller locating/mounting bolts, so well see how that works out |
Re: PO has me PO'd
Ordered my injectors from fast today, 36 lb@58 psi=331.00. Still working on my order for fuel line 3/8" wall thickness. 035, 90/10 copper nickel
Went to offer up fuel tank and ran into a problem, if i put into stock location, interferance with second to last cross sill, could fix it by sectioning in a piece of flat stock in the middle for about a foot and a half....alot of work! Second option, body lift of about 1 1/2", alot of work and money! Third option, relocate tank forward about 1 1/2", required to drill 6 holes, and maybe buy a new fuel filler hose. I think i will opt for 3, but everytime i think of drilling large holes, tom vogel comes to mind with a broken wrist. So, when i use my 3/4" chuck drill ill use the handle adapter and hope i can control the torque...if not the build will halt for awhile, and i will utter several curse words. Man that has got to be painful! Cant think of any options short of renting a magnetic base drill Recieved the fuel pump connecter from vette works out in washington state. Only need two leads 12v, and ground, other two will be deleted, they are for the sending unit, and i am using the oem sending unit that came with the tank Gotta take the connecter apart, and check what pins they use, i want to get rid of any splices http://farm4.staticflickr.com/3727/9...bc98bcd0_c.jpg 20130723_135557 by jarosaj, on Flickr |
Re: PO has me PO'd
Hey Jim a lot of nice machine work just on that ring alone...if I may ask the dumb question whats the problem with the tank install? fuel supply and return lines, ..Also this is going to be a pressure system will an original filler neck seal enough.? Ed.
|
Re: PO has me PO'd
Quote:
The whole problem with the install is that the pump can only mount in one flat spot on the tank, so all changes have to be made to accomadate that location. The actual lines seem to be the easy part, i can rotate the pump just about 360 degrees, just not aimed at the cross sills The pump shouldnt build pressure in the tank, as it has a vent system right between the supply and return line fittings. So, there shouldnt be any pressure at the fill cap. Hope i answered your question. I dont believe there are any dumb questions on this board, if you dont know the answer, then you have to ask the question..... |
Re: PO has me PO'd
I am sure You will come up with a good compromise, I put a poly tank in 15 yrs ago, it was loose side to side and I didn't like the way it fit. I added a 1/4" angle 3 x 3 x 8 on both sides and 1/4 rubber mat to cushion it. This moves the tank down 1/2" and gives a little clearance. Short stubby fuel fill on tank got a longer hose. Might be another option to consider.
|
Re: PO has me PO'd
Quote:
I think the proper way to tackle this problem is going to be modiying the the second to last cross sill, so, i hope one of our arizona boys have a bed they want to chop up. Doesnt seem that the sill is in repop, i think it is blazer/jimmy specific |
Re: PO has me PO'd
http://farm4.staticflickr.com/3730/9...875c6ee5_c.jpg
20130730_114138 by jarosaj, on Flickr Got a couple minutes to work on the retaining ring, now i can just use a transfer punch to referance my holes for the nutserts in the tank. Probably using 6 to mount it up Still working on the fuel injectors, seems they are more costly then originally planned. Sent the original injectors back to fast Not sure of these quick connects, reading some bad things |
Re: PO has me PO'd
Jim
Make sure if you are drilling the holes for nutserts you use the knurled type. If you use the smooth type on anything other than a punched hole they will eventually slip and make it so you cant get the bolt back out. Ask me how I know LOL. McMaster has both kinds. Richard |
Re: PO has me PO'd
Quote:
Just ordered my 90/10 fuel line, and 1/4" brake line |
Re: PO has me PO'd
Just looked in mcmaster-carr, and cant find the knurled body
|
Re: PO has me PO'd
If you have book 119 it is page 3270 or go to there website McMaster.com and type "heavy duty rivet nuts" it will bring you to next screen that has option for heavy duty rivet nuts. from there you can choose what type (open /closed and metric / SAE)
Richard |
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Ok, found the twist resistant net sert...90720A450. Gotta check out the tool they recommend for installation
|
Re: PO has me PO'd
Jim,
If its not something you are going to use all the time I have a gun you can borrow. Richard |
Re: PO has me PO'd
Quote:
Having a hard time downloading that part number.... |
Re: PO has me PO'd
If I recall it is around $100 for a decent gun that wont break after 4 or 5 pulls. I can also send ya some gripcerts and the 25/64 bit if its just gonna be a one time thing for you. Just let me know if I can help. I will have to check but I think it will all fit in a flat rate box so it would just cost ya 6 bucks to send it back when your done. This is my manual gun that I dont use anymore. Just keep it for backup in case my high lever gun breaks, so its no rush sending back.
Richard |
Re: PO has me PO'd
1 Attachment(s)
Jim,
I have had the best luck with the 95105A143 nutserts. They look like this. I also checked the gun size and it will not fit in small flat rate by about an inch. UPS ground appears to be about 10 bucks each way. Richard |
Re: PO has me PO'd
Richard, im going to take you up on your offer....thank you very much. Ill pm you my home addy and ill place an order for the cert you advised.....
Do you have a paypal account? |
Re: PO has me PO'd
http://farm4.staticflickr.com/3742/9...12a34c40_c.jpg
20130731_110023 by jarosaj, on Flickr Richard, this the device i was using, simple, i know.... |
Re: PO has me PO'd
Quote:
Richard Supplies are waiting to go out UPS now so you should have them tomorrow. |
Re: PO has me PO'd
1 Attachment(s)
This is the gun I am sending you.:sexy:
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Richard, got the installation tool today, plus the new drill bit...youre the man, actions like that make this board work.
Thank you very much, whats your paypal addy.... |
Re: PO has me PO'd
Don't worry about it. Just make sure it works for ya. Glad someone is working on theirs. I have been in limbo since my car accident back in Nov.
Richard |
Re: PO has me PO'd
http://farm6.staticflickr.com/5498/9...f3eb0b8d_c.jpg
20130801_134310 by jarosaj, on Flickr Got the first one installed, seems to be a little loose, guess i have to play with the stops Yep, tightened up the bottom collar, pulled the rivnut much tighter Having the right tool for the job, always makes the outcome of the work better |
Re: PO has me PO'd
If it bottoms out before it is fully tight turn the wheel on the back of the head clockwise while the gun is released but still inserted in the gripsert. Squeeze the handle again until you get it tight enough. It is hard to apply enough pressure to break the mandrel but it is possible to break it so you just have to find that happy medium. The madrels are replaceable so no big deal if you should snap one. LOL
Just make sure not to leave that 1st one loose. U can screw the gun back in and go again. Richard |
Re: PO has me PO'd
Jim, its lookin' great. Can't wait to see/hear a vid of it at idle. Nice work my friend.
|
Re: PO has me PO'd
Quote:
Quote:
A video may be outside the reach of my technology, but we shall see..... |
Re: PO has me PO'd
http://farm6.staticflickr.com/5501/9...da861445_c.jpg
20130802_131245 by jarosaj, on Flickr Success...only one hole needs to be tweaked alittle, but that is what happens when you rush and dont check every hole Thought the black oxide ss would look sexier...lol shame noone will ever see it, except for yous guys Got the bolts from mcmaster-carr, its like having a well stocked hardware store on your front porch Thanks Richard, please pm me your addy....does this count as "members i have met" http://farm6.staticflickr.com/5473/9...0c515abd_c.jpg 20130802_130559 by jarosaj, on Flickr |
Re: PO has me PO'd
Looking good Jim. No paypal needed.... Just send gun back when ur finished.
I feel pretty sure we will meet at some point. I need to get back up and see Dusty's and John's rigs as well. They will be wrapping up soon and driving as well. Richard |
Re: PO has me PO'd
http://farm6.staticflickr.com/5538/9...a073a366_c.jpg
20130804_083211 by jarosaj, on Flickr Ok, finished up the retaining ring, now i can go back and finish the mods on the two remaining ss support rods, and wire up the fuel pump....plus vacuum out the tank of all my machining debris. Pulling the ring down presents a problem since they dont seat tight on the tank. I plan to use lock washers and a thread sealant, and hope it seals tight, if not, ill have to buy new bolts and safety wire it in place. Another option i have is to build spacers between the tank and ring, then i could pull the ring down tight. Then i can offer up the tank to the body, still thinking of moving the tank forward two inches to clear the rear body mount, dont want to fool with taking the stubby neck off and replacing it with the oem neck, unless im forced to....to be determined! Sandemonium posted up a 1 1/2" 90 degree fuel hose(gates 24715) which napa has a superceded number for. Ill order the hose on mon. and see how this works out with fitting up the tank Still have build a tool to install the retaining ring on the fuel sending unit... Thanks Richard for making this step as painless as possible |
Re: PO has me PO'd
http://farm8.staticflickr.com/7332/9...1b259039_c.jpg
20130806_125635 by jarosaj, on Flickr Did mine a little differant, used a 45 degree 1 1/2" hose(napa 1031) , cut about 4" off the hose,and cut about 1" off the stubby neck of the gas tank. Broght the hose out just in front of the body mount. Then went over to my local muffler shop, he had a piece of ss 1 1/2" , perfect, gave him a template of the bend i needed(about 20-25 degrees). Ended up real close to the fill pipe, just used the straight piece of hose i cut off the 45, and it gave it enough wiggle room Dont forget i moved my tank forward about 2".... http://farm6.staticflickr.com/5524/9...dfae11e1_c.jpg 20130806_125553 by jarosaj, on Flickr Sheesh, 2 pages on this gas tank, now i have to work on the straps |
Re: PO has me PO'd
Received my 90/10 copper nickle tubing today, the company wanted to hold off posting this info. until we could show that shipping this matrl. was viable. Normally, they ship in 8' cardboard tubes, but i wanted the 1/4" (brake lines) coiled and shipped. They had never coiled before, and i had to sign a release for damage that might happen in coiling and shipping. Coil arrived sandwiched between cardboard and 1/4" plywood, banded with steele straps.....no way was UPS going to damage this product coming across the great USofA
Tubing for my gas lines is 3/8", and shipped in straight 8' tubes(UPS regulations), thats where the problem lies. In pa., we cant use splices in our brake lines. So, they coiled a 20' piece, and that should be enough for my back brake lines I may contact in line tube to see if they will sell me the coiled spring cover they use, may want to shield tubing from flying rocks outside of frame rails....well see If you have any questions about using this matrl. in an automotive application, you can contact cda.copper.org, they answered my questions quickly by email. They assured me that alcohol will not corrode the nickle/copper in my fuel lines http://farm3.staticflickr.com/2888/9...13a20750_c.jpg 20130808_115426 by jarosaj, on Flickr |
Re: PO has me PO'd
Been using the nicop from napa for a few years now on different projects. I love it bends easy and flares awesome which is super nice for double flares.
Posted via Mobile Device Posted via Mobile Device |
Re: PO has me PO'd
Quote:
Ill try a test flare today, i have to buy some barrel nuts and adapters to see how it works with a 45 degree an fitting. Dont have a 33 degree flaring tool, but have read that -6 and -8 are ok with a 45 flare Hows your build going, ill have to drop down and check it out, dont have alot of time to surf the web and keep in touch with all the builds i would like to follow |
Re: PO has me PO'd
http://farm8.staticflickr.com/7395/9...4a0fb1a7_c.jpg
20130815_103812 by jarosaj, on Flickr Got more fittings and russell pro hose in...( thanks JJK for the product info), found out that jegs fittings are about a 1/3 the price of russell. Putting the hose end on requires the use of grease on the threads Have to build a bracket to support the hoses coming around the power steering These are the clamps and some of the fittings im using....i just realized why they are a 1/3 the price,damn http://farm4.staticflickr.com/3678/9...c552a1f1_c.jpg 20130815_113410 by jarosaj, on Flickr |
Re: PO has me PO'd
Looking good. Happy Birthday
|
Re: PO has me PO'd
Thanks Richard, the word got out, 63 today! Getting to ship that tool back, ty
http://farm8.staticflickr.com/7367/9...50b97f71_c.jpg 20130815_120652 by jarosaj, on Flickr |
Re: PO has me PO'd
Great work and HAPPY BIRTHAY. http://i47.photobucket.com/albums/f1...ps93ae87ad.gif
|
All times are GMT -4. The time now is 05:52 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com