Re: What did you do to your truck today part IV
1 Attachment(s)
Replaced the turn signal switch on my '66 C20
|
Re: What did you do to your truck today part IV
Fixed my rear LED turn signal/brake lights. Found out last night that I had no turn signal or brake lights when my headlights were on.
Spent 5 hours on them today. Got frustrated. Went to a buddies house. “Try swapping the two connections around. See what happens” …..damnit. |
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Quote:
Yes. It was a screw up on the original builders part. The Tail and Brake wires were switched and I overlooked it. Everything works fine without the headlights turned on. Turn them on….and no brake lights or turn signal, but DRL are full brightness. Should have caught it. Now I have it. Swapped them around and g2g. |
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
My Sanity has left the building. The '66 is off to the painters to get the roof painted. It should be done in about a week.
|
Re: What did you do to your truck today part IV
1 Attachment(s)
Assembled and installed a Craftec cover on the ‘65. Nice product!
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Bought fender emblems, and installed a new thermostat. Cant get the truck to run over 140*, so purchased another thermostat to try.
|
Re: What did you do to your truck today part IV
Quote:
|
Quote:
Front of the intake just next to the thermostat housing. Edelbrock RPM intake Posted via Mobile Device |
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
What AM I going to do today?
Drill holes in my upper fender shroud things to mount the emblems…..gotta talk myself into it though. |
Re: What did you do to your truck today part IV
3 Attachment(s)
Took my latest project in for front end alignment, all good to a point, all systems functioning, brakes bedded, clutch a bit stiff, will take some getting used to or adjust later, corners like a go cart, only glitch, 78k mile transmission seal decided it want to leak….easy fix, new seal will be here tomorrow…
|
Re: What did you do to your truck today part IV
Looks great Mike!
|
Re: What did you do to your truck today part IV
Went and got it from storage! Started right up, great drive on country roads home.
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
1 Attachment(s)
Cleaned up the taillight connections.
Lights are a lot brighter now. Had to use PB Blaster to get the old bulbs out. |
Re: What did you do to your truck today part IV
|
Re: What did you do to your truck today part IV
Nice TJ!
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Sounds great TJ! Looks great too! Glad to see I am not the only one that uses Spray Max 2K clear coat in a rattle can! :)
|
Re: What did you do to your truck today part IV
Sounds pretty rowdy. Not what I would expect a straight 6 to sound like.
|
All times are GMT -4. The time now is 10:25 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com