Re: '72 Cheyenne K10
About your brakes- You might want to pull your master and booster apart and see if there's a gap between the rods. The one coming from the booster is adjustable and you want them to juuuuust touch at rest. I bet you have a small gap in there. Just went through this with my new build. Beater 4x4 looks great!
|
Re: '72 Cheyenne K10
4 Attachment(s)
I don't have a lot to show for day 1 of Vintage Air install. I assembled the condenser and drier, but the "well nuts" provided do not fit through the factory holes in the core support. I really don't want to take the grill off just to make two holes slightly bigger.
Speaking of taking off parts to make holes... I thought I wouldn't have to take the inner fender off since the previous owner removed all the factory ac components. It turns out I will just to drill a few holes for installing the firewall plate. All the old rusty bolts for the inner fender came out except one, and it has me defeated for today. Too hot outside to continue. Attachment 2038244 Attachment 2038245 Attachment 2038246 Attachment 2038247 |
Re: '72 Cheyenne K10
always has to be one bolt that won't cooperate...
|
Re: '72 Cheyenne K10
I hear that it's hot there. I just watched the noon news. Keep plugging away at it your experience is gonna help me out.....lol..
|
Re: '72 Cheyenne K10
2 Attachment(s)
Jimbo, hate to say it but you're gonna have to take off at least the inner grill anyway. I'm finishing up the VA project now, and there was no way to put those aluminum lines through the core support with all their bends with the inner grill installed. Pretty quick taking it off, 8-10 screws maybe? I just dropped it down, did not remove it completely. The rubber well nuts were bigger than the holes in my core support also, just drilled the holes SLIGHTLY bigger.
Would also be hard to do this without dropping the inner fender, be easy to drill right through it when you make your drain hole later. I left the front vertical bolts installed loosely, no need to take the inner fender off completely unless you want to for some reason. See pic, it's just hanging there by the front bolts. Also, quick tip, before you bolt in your AC unit in the cab run your wiring harness wires through the grommet in the firewall. It was kind of a PITA to get back behind the box and run the wires with the AC box in the way. |
Re: '72 Cheyenne K10
Quote:
|
Re: '72 Cheyenne K10
2 Attachment(s)
I got it. It took two pairs of vice grips and a lot of cursing, but I got it. The darn clip on nut behind one bolt was busted.
Attachment 2038286 Attachment 2038287 |
Re: '72 Cheyenne K10
1 Attachment(s)
My engineer friend helped me design a rear bumper in Solidworks. He is going to cut and form it at his work.
Attachment 2038358 |
Re: '72 Cheyenne K10
That bumper looks pretty nice
|
Re: '72 Cheyenne K10
4 Attachment(s)
I finished mounting the firewall plate this morning. The fresh air duct and the kick panel vent are sealed off too.
Attachment 2038515 Attachment 2038516 Attachment 2038517 Attachment 2038518 |
Re: '72 Cheyenne K10
5 Attachment(s)
I found the factory AC vents that were in a crate of parts the previous owner of the truck gave me. A quick wash and they were ready for the Vintage Air duct adapters and installation.
Attachment 2038519 Attachment 2038520 Attachment 2038521 Attachment 2038522 Attachment 2038523 |
Re: '72 Cheyenne K10
3 Attachment(s)
Per the advice from NorCalC20LWB, I accepted my fate and tore the grill and bumper off the truck for access to install the condenser. I also ran the wiring through the firewall before the evaporator, which I assembled this morning.
Attachment 2038524 Attachment 2038525 Attachment 2038526 |
Re: '72 Cheyenne K10
It's looking good, your making it look fairly simple too.
|
Re: '72 Cheyenne K10
Man, Jimbo, you do move right along, looking good! Good idea to take the whole grill off, couple of extra bolts but then you don't have to deal with the hassle of putting the grill insert screws/plastic nuts back in. Once you get the inner box in it's pretty much smooth sailing from there.
|
Re: '72 Cheyenne K10
3 Attachment(s)
All I had time for today is the condenser hard lines, safety switch, and reassembly of the grill and bumper.
Attachment 2038659 Attachment 2038660 Attachment 2038661 |
Re: '72 Cheyenne K10
The condenser and hard lines look clean. Were they prebent?
|
Re: '72 Cheyenne K10
Quote:
|
Re: '72 Cheyenne K10
Quote:
|
Re: '72 Cheyenne K10
2 Attachment(s)
I went to replace the crank pulley this morning and found an unexpected issue - the harmonic balancer crank bolt is missing. I can feel threads, but the hole was full of mud like it has been missing for a long time. I think I have to fix this.
Attachment 2038889 Attachment 2038890 |
Re: '72 Cheyenne K10
1 Attachment(s)
Jimbo, I just finished my VA install and had it charged, you will like the results, ice cold! If your truck was a non AC cab, do you need this part? It's the bracket to connect the AC lines to the battery box. If you can use let me know and I'll get it in the mail. I didn't need it because mine is an AC cab.
|
Re: '72 Cheyenne K10
Quote:
|
Re: '72 Cheyenne K10
1 Attachment(s)
The evaporator is installed under the dash.
Seriously, why a 5/8" hole for the drain? Nobody has a drill bit that size. It costs almost $20 at Lowe's to buy one. I have a tough time spending that just to drill one hole. Attachment 2038915 |
Re: '72 Cheyenne K10
Quote:
|
Re: '72 Cheyenne K10
2 Attachment(s)
Quote:
Attachment 2039067 Attachment 2039068 |
Re: '72 Cheyenne K10
3 Attachment(s)
Harmonic balancer bolt was just missing. I got a new bolt at the parts store and installed the new pulley without any issues.
Attachment 2039087 Attachment 2039088 Attachment 2039089 |
Re: '72 Cheyenne K10
Looking good.
|
Re: '72 Cheyenne K10
2 Attachment(s)
|
Re: '72 Cheyenne K10
Quote:
|
Re: '72 Cheyenne K10
1 Attachment(s)
FedEx said my compressor and controls were delivering yesterday but they didn't show. So today I played with wiring for the new gauges. Temp and volt gauges will be custom fit into the cluster, and the tachometer will hose clamp onto the steering column.
Attachment 2039382 |
Re: '72 Cheyenne K10
Jimbo, you will love your VA unit. Had mine charged Friday and took it out today to the Placerville wine country, high 90's to 100 and blew ice cold. Took no time at all to start blowing cold after starting up in a hot cab. The original AC in my truck never worked, so I can't compare to stock, but I really don't think it would be better than this.
|
Re: '72 Cheyenne K10
Quote:
Question - does it use a regular factory AC belt? |
Re: '72 Cheyenne K10
2 Attachment(s)
Here's the belt I used, Gates, pretty sure 58" I think which is what VA recommended, stock pulleys. Not sure what you mean about fans, I have a stock setup.
|
Re: '72 Cheyenne K10
5 Attachment(s)
Custom voltmeter and temperature gauges are in the instrument cluster. They look good in the daytime, but I wonder how they will look at night with the lights on.
Attachment 2039668 Attachment 2039669 Attachment 2039670 Attachment 2039671 Attachment 2039672 |
Re: '72 Cheyenne K10
They look good. Don't forget to take a night pic for us.
|
Re: '72 Cheyenne K10
4 Attachment(s)
Today's progress (so far):
Attachment 2039894 Attachment 2039897 Attachment 2039895 Attachment 2039896 |
Re: '72 Cheyenne K10
3 Attachment(s)
How does an old work truck not have any tie-down anchors? I fixed that.
Attachment 2040018 Attachment 2040019 Attachment 2040020 |
Re: '72 Cheyenne K10
1 Attachment(s)
Quote:
Attachment 2040041 |
Re: '72 Cheyenne K10
Quote:
|
Re: '72 Cheyenne K10
It’s all looking good, great job.
|
Re: '72 Cheyenne K10
4 Attachment(s)
Compressor install was easy. I really appreciate the previous owner using anti-seize on the exhaust bolts. Now I am on the hunt for a shop with the crimping tools to make the AC hoses.
Can anyone tell me if the main power for the Vintage Air is safe to hook up to the battery side of the American Autowire Megafuse? |
All times are GMT -4. The time now is 05:26 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com