Re: Rat repair.
Good to see progress again, good score on the slots and dash! Tires under 10 years can be remounted, so you have time. I can't believe you'd get a ticket for that, I'd think you'd have to have obscene protrusion for it to be an issue unless you live in a utopia that has no real issues for cops to pursue.
Keep in mind that the area that will suffer is still the lower part of the front fenders and even with flush or narrower fitment, that area still gets a ton of rock chips unless you have flaps. I think your new rear bumper must be like mine? 80's style? |
Re: Rat repair.
Quote:
|
Re: Rat repair.
Quote:
Don't tell nobody but the bumper came off of a 4 letter F word. I have given thought to trying to modify the old bumper being as i have a Mig and Plasma cutter till i can find a different period correct bumper that i like. |
Re: Rat repair.
Quote:
The wheels i got need an acid bath, if you look back in the build i have some Muratic Acid, that stuff is super toxic and vapors are killer, before i use it again i will have a respirator on, it should be here by Tuesday at the latest. Starting out slow this year but like a terminator when it comes to this truck i will not stop. :) |
Re: Rat repair.
5 Attachment(s)
I started out my day today at 4:30 am waking up (groggy as hell) and drinking my coffee, then taking my wife to the oral surgeon to yank a tooth and a few other things to her upper jaw (whatever you call it) to prep for a tooth replacement, another $2000 bill on my Visa after insurance. Whats another temporary setback... LOL!
I got the car canopy up behind the old one and lashed then together last Monday, of course it was raining when i did that.. Then i scrounged up a couple wooden crates from the scrap yard at work to use as stands to set the bed on. I also bought 3 sheets of plywood to act as a temporary floor under the engine hoist as the ground is pretty soft, i let it dry under the cover for 3 days then got started. First the tailgate and the 100 lb bumper had to come off, then i rounded up a couple 2X4's some clamps and extended the lift out, not the best but it worked better what i rigged up the last time i pulled the bed, thanks to this forum for the ideas, i did forget to add some wood under the bed rails so all the weight was on the bottom of the flange (woops) but i didn't do any real damage thankfully. I ground the rivets and removed the rear cross member after i clamped a piece of square stock across the rear of the frame, i didn't know if it was gonna spring in or out, so just being cautious. i tried 3/8 a bolt in the rivet hole but it was a little sloppy fitting so i dug around and just happened to have the perfect step reamer, just .006 larger than a 7/16 NF bolt with a pilot the same diameter as the existing rivet hole, off to the hardware store for 7/16 Grade 8 bolts nuts and washers. One of the reasons i wanted to pull the rear cross member and make it removable was so i could hopefully gain access to the 2 bed bolts above the tank, last time i put the bed on i couldn't reach the two bolts to put the two nuts and washers on no matter what i tried. The bolts are much closer to the rear of the tank and with the cross member removed i can get my Popeye forearms between the tank and frame rails enough to access the bolts. The only problem with having rear cross member removable is the top of the cross member needs the to also be bolted and the nuts and washers would no longer be accessible, so i think the solution will be to weld the nuts to the inside top of the cross member and then i should be able to access the bolt from the top without too much trouble, hopefully! The other reason of course is i want to put the tank between the frame rails instead of just bolting it to the bottom so the filler will be up higher. there is currently 1 1/4" from the top of the tank to the top of the frame rail, i have some 1" square tubing that i think will raise it up enough to allow the rubber fill hose not to rub on the frame, as a back up i also have some 1 1/4" square stock as well. The only other option i can see would be to ether cut a notch out of the frame which i absolutely do not want to do, the other is get a torch (another purchase) and heat it up and bend it down. I guess the only other option from all this would be to take the tank to a weld shop and have them remove and re weld the flanges lower on the tank but i'll save that as a last resort.. |
Re: Rat repair.
lookin good!
|
Re: Rat repair.
Excellent progress. Love those slots, hope you use them.
|
Re: Rat repair.
Nice work Rat, and glad you're feeling better!
|
Re: Rat repair.
3 Attachment(s)
Today I welded a couple nuts on the top underside of the rear cross member so it could be bolted from the top, and then thru bolts and nuts on the bottom.
Removed the tank and slid it between the rails, realized real quick i needed way less that 1" of spacer to get the tank high enough. when i mounted the tank on the bottom of the rails the first time i used rubber washers to isolate the tank and eliminate the contact of dissimilar metals, seemed like a good idea at the time so i did it again today. Went to the hardware store and bought a foot of 1/8" rubber sheet and cut it into strips, first i used some 1/8" X 2" angle iron i had laying around, then 2 strips of rubber then the tank followed by another strip of rubber, then another smaller piece of angle for an upper cap followed by lock nuts. it don't look pretty but this isn't a show truck, if i find the rubber was a bad idea then I'll just have to pull the bed and change it out to something like steel strap. Oh, it looks a little funny because i notched the rear of the tank flange to clear the spring mounts on the underside of the frame, but the tank flange is wider than the rubber strips and angle and there is now plenty of clearance for the hose to not hit the frame.. Then i brought out the new Curt hitch and mounted the two center holes thru the existing holes in the bottom of the frame, still need to drill 4 holes. Looking at it the frame rails sure seem thin, i cant help but wonder if the frame will end up bending under the weight of towing.. Also i did some preliminary barnyard measurements and I'm a little concerned if this hitch will extend out far enough with the bumpers i have so i came to the conclusion i'll probably put the bed back on tomorrow first, then take a good look at the bumper situation, i know I'll ether have to modify my existing bumper or try and mount the other one, or maybe just make a new one?? beginning to like that option. |
Re: Rat repair.
Quote:
Quote:
Quote:
|
Re: Rat repair.
5 Attachment(s)
Well well, one step forward and 2 steps back again... :)
A trip to the hardware store and then wrap up a few loose ends then decided to put the bed back on to see how far out the back the hitch sits when using the one existing hole in the bottom of the frame. I picked up the bed and got the dunnage out of the area and backed the truck into place, lowered the bed down and got it aligned as good as possible then relaxed the lift. It took me a while to figure out why the bed just wouldn't slide that last inch to get back into place.... :) Before i raised the tank the vent was low enough that it was under the bed cross member, guess i forgot about that when raising the tank, even worse if you look at the pic's where the cross member sits it was plain as day.. Oh well So I had to lift the bed back up, pull back out from under it, remove the hitch and unbolt the tank from the frame and fuel line, reposition the tank forward while using a 2X4 to gauge the clearance to the vent (yes a 2X4 is 1.5" and the cross member is 1.75") then take measurements from the rear of the frame to the tank, pull the tank back out and reposition underneath the frame and transfer the mounting holes from the tank back to the frame and put it all back together again then re bend the fuel line a bit and shorten and re flair it. The tank was moved forward about 1 1/4". I also decided the hitch could be moved rearward almost another inch if i plugged the two existing 3/4" holes in the frame and re drill all 6 holes. Welcome to my welding booth complete with wet dirt ground, yea its been dumping all day again and the water leaches back under the cover. Oh my 220V extension cord had to be run from the garage outside and under the car cover too. The pic shows the top which was welded first then ground flush, then welded from the bottom. |
Re: Rat repair.
5 Attachment(s)
What i was faced with this morning.. I decided to straighten up my work bench a little and then mocked up the hitch where i want it and clamped it in place then gathered up the needed drills and called it a day so i can get ready for work. Didn't get a pic of the mock up but by welding up the existing hole i was able to extend the hitch out another inch.
|
Re: Rat repair.
4 Attachment(s)
So this week i haven't been sitting idle, but i have only been getting in about 2-3 hours a day to work on the truck, that included dragging all the tools need out and back in again.. I hate not having a shop.. :)
I have had the bed on and off two more times this week test fitting and checking everything, the tank is now positioned so not to interfere with the bed sills, and i had to cut the leg off the angles i used as a top cap to bolt the tank in because i couldn't reach the bed bolts. I'll leave the bed unbolted for now in case i need it off for body stuff. I settled on the hitch position and drilled the 6 holes and got it drilled and bolted up, I decided not to push it and left about 3/4" from the rear hole to the edge of the frame, i was originally going to move it back further but decided safe would be better than gaining another 1/4" out the back. As i may have mentioned i wanted to retain the cross member in the stock location because its very close to the rear springs and shackles, If i just removed or moved it i think it would have allowed the frame to flex too much. The other reason was so i could access the tank bolts on ether side of the tank that i couldn't reach from the front, And it worked, with the nut welded to the upper leg of the brace i can run bolts in from the side, and the bottom bolts and nut's are accessible from underneath. Lifted the bumper i picked up on the cheap up to the truck, i hate it, so I'll keep looking. Anybody know if any of these 1/2" hols in the frame are factory? |
Re: Rat repair.
5 Attachment(s)
I got the gas fill door surround cut and made my preliminary layout of where i want the door, I'm not worried about cutting the hole anymore, but i still have some rippling problems I'm trying to get out, i was working the lower portion using the hammer off technique and got a high spot out but in the process it created an even bigger high spot on the upper section..... Go figure
I need to pull my inner bed fender wells soon, i'm seeing some pretty nasty looking rust on the back side where they bolt to the inner bed. I'll give it another go soon but probably not this weekend, there is a swap meet tomorrow downtown i want to check out, then i got to go to work. |
Re: Rat repair.
2 Attachment(s)
I need to get these fender wells off pretty quick too!
|
Re: Rat repair.
Good progress. Keep picking away. The no shop thing I'm sure is a pain, but your definitely doing good without!
|
Re: Rat repair.
not having a shop must be a pain...im spoiled with my nice one...... Good job!
|
Re: Rat repair.
3 Attachment(s)
Well its not much but its something, the rain has been non stop for days until about an hour before i left for work yesterday, but i was able to get a little bit done today..
Guess i got over the "fear factor" on poking a hole in my bed, still need to fit it a little more I still have some couture issues that need sorting out but i thought maybe this might help me get them worked out ether by relieving stress or gaining access to the back side? Kinda surprised at how much rust is back there, makes me cringe thinking about the cab.... :lol: |
Re: Rat repair.
Looks good man, id like to do a bedside filler but after I dont want to redo my paint im just goin to doing a stake pocket filler.
|
Re: Rat repair.
Well nothing accomplished today. I got an electric abrasive 3" cutoff tool from Harbor freight for Christmas, never used it till yesterday, as i was using it to rough the door opening it started to loose RPM as it got warm. I figured today was the day i better get it exchanged under there 90 day satisfaction guarantee, made it by a day or two..
So driving there, spending time in the store and home killed most of my morning.. I did buy one of there 18" metal brake forum tools to i can make the filler tube cover for the bed. EDIT: I should add, both of my key fobs have now failed dor my DD> so now tomorrow i need to go buy new ones and get them programmed and cut.. another nice chunk of change... and time away from the truck.. |
Re: Rat repair.
Nice work. Planning a bedside filler for mine, too.
|
Re: Rat repair.
hey cool. looks good, keep at it man
|
Re: Rat repair.
70stroker, Mustard72, Dean'smeanmachine,
Thanks for the compliments, now i just need to find a bit more time to finish it! :lol: |
Re: Rat repair.
Keep plugging away buddy! Spring is almost here, and before you know she will be done!:metal:
|
Re: Rat repair.
Quote:
Still trying to decide if and when i get the rust repaired if i should attempt a piece by piece paint job in the yard (under a car cover of course)... Or just shell out some big bucks.... :lol: |
Re: Rat repair.
2 Attachment(s)
Well I'm working this weekend again, had a late start today because i was up late working on my new cluster, but i was at least able to get out there for about an hour today before work.
I'm still fighting that large high spot that starts at the body line and go's up about 3-4".. I have been able to move some metal and made some improvement but i want that large high spot out before i weld in the door, I'm half tempted to take a cutoff wheel and make a slit right into the center of the high spot in hopes it will lay down but kinda afraid i'll open up a can of worms (oil canning maybe?) that i don't want. I'm to the point that if i had a patch panel in that area i'd probably go ahead and cut the area out and weld in the patch. I can at least say my stud gun works and Fedex just delivered a dent puller i ordered to work some of the smaller creases, it looks like a rivet gun but has a round cage that attaches to it to the working end to localize the pull. EDIT: I know the ridge has a couture the length from the rear of the truck to the well opening, just using the level as a reference. Here,s a link to the tool: Ding-Near-Perfect Dent Puller : Amazon.com :.... . . . |
Re: Rat repair.
keep at it:metal:
|
Re: Rat repair.
The pros use a flash shrink gun when the metal is stretched out like that and short of using one I don't know of another method that would give a similar result, maybe Vic has some ideas for you.
|
Re: Rat repair.
1 Attachment(s)
Quote:
Start by locating the highest part of the crowned area. You'll need to remove the paint so the gun can do it's job. With the shrinking tip inserted, start at the very center and heat a spot for 1-2 seconds then release the trigger and continue to hold the tip against the metal for several seconds. Move out about an inch and repeat at 3, 6, 9 and 12 o'clock. If needed, move out another inch and repeat in a circular pattern. Some guys lay out a spiral pattern, but I prefer concentric circles. Some guys will tell you to cool the hot spots with a damp rag or compressed air, but the procedure works fine without it. Like nearly all metal and body work, this can be technique sensitive. It is very easy to over-shrink a high spot. But you can always fix that with some draw pins and filler. High spots have to come down regardless if you want the panel right. Good luck! |
Re: Rat repair.
Quote:
In the pic's the high spot I'm showing is right on the body line and extends both upward and downward with the worst being above the body line, if i do shrink above and below the body line should i attempt to shrink the body line as well? The high spot on the body line is the area I'm having the hardiest time dealing with. I understand what your getting at with the shrinker and will see about finding a shrinking tip. I was also told a few years back to buy a shrinking disk but never got that far before i got side tracked on this truck due to injury/house remodel. Here's the past history, thanks again Dieselwrencher for letting me invade his thread. http://67-72chevytrucks.com/vboard/s...d.php?t=426756 |
Re: Rat repair.
Quote:
|
Re: Rat repair.
Ok Vic thank you again.
I'm leaving for work again soon, just too tired to get out there and work on it today. Getting ready for a nice corned beef cabbage, potatoes and carrots lunch, the house smells great! |
Re: Rat repair.
Quote:
|
Re: Rat repair.
Quote:
|
Re: Rat repair.
Good eats! Not the Pop Tart, though.:lol:
|
Re: Rat repair.
An no serpents be drivin away! LOL!
|
Re: Rat repair.
Dont you just hate warps..lol
|
Re: Rat repair.
Quote:
|
Re: Rat repair.
1 Attachment(s)
Ok be sure to visit this thread in the near future :)
http://67-72chevytrucks.com/vboard/s....php?p=6578527 Thought i'd post the original picture of the rear quarter dent, man if there was only a dent Doctor back in the late 80's.... Amazing how much more damage i have caused just trying to pop the dent out myself.. :lol: |
Re: Rat repair.
4 Attachment(s)
The last couple of days(or in this case late nights) i have been working on the bezel i bought, it has been taking up space on my desk and i need the space to get my taxes done.. Here's the before and after pic, still don't know when i'm gonna get around to installing it. Polished the lens to remove the scratches it was really hazy, repainted all the needles, replaced the temp gauge and cleaned it up a bit, there was a film of some kind allover the speedo, tried soap and water and didn't faze it, ended up rubbing it with carnuba wax for about 1 hour and got most of it but not all
|
All times are GMT -4. The time now is 10:31 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com