Re: What did you do with your truck today, take 2
Bit the bullet! Took off the front of the 57. It was surprisingly easy as I have not taken off the fenders before. I will repair most of my previous mistakes, custom radiator supports, including steering, changing to IFS, exhaust that falls off every week, replace the lower sheet metal that bent in an accident, and add a condenser for a/c when i put it back together.
|
Re: What did you do with your truck today, take 2
Got new front tires, the old ones were balding and kept losing air.
Put the side rails back on the flat bed. I sanded down and refinished them. They were grey and worn like the bed is now... gonna refinish the bed next. There was a debate with friends and family whether the side rails should stay off or on. I think I like it better with the side rails on. http://i139.photobucket.com/albums/q...ps5577c0da.jpg |
Re: What did you do with your truck today, take 2
Quote:
|
Re: What did you do with your truck today, take 2
Quote:
|
Re: What did you do with your truck today, take 2
1 Attachment(s)
Did me some bed wood....
|
Re: What did you do with your truck today, take 2
Was actually late last night but I started planning a total re-wire of engine & body. I'd gotten the truck running but never could make it "clean"... hoping to fix that.
|
Re: What did you do with your truck today, take 2
1 Attachment(s)
Got the new rear shock mounts welded in and painted. Had all the new brake lines in and ready to bleed but stripped out the proportioning valve (aluminum) on the last line going in so had to order a replacement...maybe next week.
Very close to having it back on the road! |
Re: What did you do with your truck today, take 2
1 Attachment(s)
Finally got around to fixing something that had been bugging me since I got my truck. The right front radiator support pad had no shims or cushions at all, metal to metal and about 1/4" slop. Went to my local Ace hardware and got some rubber washers and nice thick steel washers and installed them. no more clanking over the bumps!
|
Re: What did you do with your truck today, take 2
Finally got around to installing speakers. Just finished and haven't driven it yet to see how it sounds when it's competing with wind noise, but it sounds good sitting in the garage.
http://i91.photobucket.com/albums/k3...psjrja8rdx.jpg http://i91.photobucket.com/albums/k3...psopexpqbj.jpg |
Re: What did you do with your truck today, take 2
2 Attachment(s)
I eliminated the tailgate chains. I have been thinking of this modification for a while and finally got around to it.
|
Re: What did you do with your truck today, take 2
1 Attachment(s)
Cleaning up my tailgate
|
Re: What did you do with your truck today, take 2
I wish you were closer, my nephew owns a media blasting business in NW Georgia, near Chattanooga, Tn. He does a lot of car parts.
|
Re: What did you do with your truck today, take 2
Quote:
|
Re: What did you do with your truck today, take 2
Finished up the AC lines, now need to sell the r12 compressor and buy the r134a model. Also picked up the vinyl for the visors.
|
Re: What did you do with your truck today, take 2
was able to grab a NV3500 5speed outta P'n'P. Nice score should mate up nice w/the 5.3 that i'm going to "old school", now to get all 4.8L stuff to make it simple, well simpler. I'd post a pic but i haven't cleaned it yet.
|
Re: What did you do with your truck today, take 2
Quote:
.post a picture we do dirty . . . . |
Re: What did you do with your truck today, take 2
Yeah, post it dirty then we'll be MORE impressed when you post a clean, possibly painted picture!
|
Re: What did you do with your truck today, take 2
I decided that it was time to move the battery off the fire wall. Its new home will be down low and in front of the cab mount. Started making the new covered battery box today. It will slide forward and tip out for access. It will be finished this week sometime.
|
Re: What did you do with your truck today, take 2
Clarence :
that sounds awesome please post pics |
Re: What did you do with your truck today, take 2
iowaboynca, pictures are on my build thread. Just another old truck. Thanks.
|
Re: What did you do with your truck today, take 2
3 Attachment(s)
Building new instrument cluster. I will be using Autometer speedometer and gauges
|
Re: What did you do with your truck today, take 2
Late last night, I sectioned & re-soldered the transmission / pass. o2 sensor / crank sensor leg of my engine harness. One down, three to go.
|
Re: What did you do with your truck today, take 2
Quote:
I liked this . http://67-72chevytrucks.com/vboard/s...=567211&page=8 . http://i288.photobucket.com/albums/l...pscd9a3707.jpg . . I'm not to proud.....I like This because i just did this blasted parts Wiper motor was not working Reason... slider arms were rusted together also switch not working heavy corrosion inside Hi/LOW/OFF disassembled wiper motor/gear box and switch cleaned reassembled broke the wiper "Park" COG.? . http://i288.photobucket.com/albums/l...ps16987197.jpg . http://i288.photobucket.com/albums/l...ps514370d4.jpg . http://i288.photobucket.com/albums/l...ps2d5299b9.jpg . http://i288.photobucket.com/albums/l...pse17464b5.jpg . . http://i288.photobucket.com/albums/l...ps18918635.jpg . http://i288.photobucket.com/albums/l...ps87af4c81.jpg . and broke this {repaired} . http://i288.photobucket.com/albums/l...ps77190b30.jpg . http://i288.photobucket.com/albums/l...ps20e5349a.jpg |
Re: What did you do with your truck today, take 2
I changed power steering fluid and completely flushed out the pump and gearbox in the process.
Nothing really sexy. |
Re: What did you do with your truck today, take 2
2 Attachment(s)
Cleaned up tranny i yanked from junkyard on saturday (see before and after)
need to hit it one more time to make it really clean |
Re: What did you do with your truck today, take 2
Stared at pieces of the wiring harness, declined to solder. Hours later, on my way into the house, I removed the oil filler cap pedestal from the valve cover and screwed the filler cap directly into the valve cover. Looks much cleaner that way.
|
Re: What did you do with your truck today, take 2
Stared at pictures and decided to try and save an ol truck.
|
Re: What did you do with your truck today, take 2
1 Attachment(s)
Got my new front bed panel today
|
Re: What did you do with your truck today, take 2
1 Attachment(s)
New disc brakes
|
Re: What did you do with your truck today, take 2
Nice looking zinc coated rotor there Frank. Who'd you get it from? Jim
|
Re: What did you do with your truck today, take 2
1 Attachment(s)
Quote:
|
Re: What did you do with your truck today, take 2
Sounds like my 48. The more I do the more I see to do.
|
Re: What did you do with your truck today, take 2
Knocked the snow of of the '49s temp. garage. Come on spring time!
|
Re: What did you do with your truck today, take 2
4 Attachment(s)
got my fenders and bedsides ready to paint
|
Re: What did you do with your truck today, take 2
Last night, trimmed some fat off the coil brackets so I would show a little more of the valve cover. Could relocate but the fenders are crowded enough - maybe later?
http://i1191.photobucket.com/albums/...ps57e2ac2e.jpg |
Re: What did you do with your truck today, take 2
Started the tear down :metal:
http://i800.photobucket.com/albums/y...s4b9a0060.jpeg |
Re: What did you do with your truck today, take 2
Looks like you're getting there, My 48 isn't that far along yet. I need to find a place that sells WD40 in 55 gallon drums. Got the engine and trans today, Now to pull the 216 and begin the swap.
|
Re: What did you do with your truck today, take 2
Quote:
Anyone have any links to how to remove the steering column? |
Re: What did you do with your truck today, take 2
1 Attachment(s)
57 swb, 454ci, 700r4,
We, my neighbor who knows how to weld, and I boxed the frame and welded in the cross-member. Today will see more grinding and then this week assembling. |
Re: What did you do with your truck today, take 2
After first time rebuilding one, finally cranked engine (sbc) about 2 1/2 years into project... got through cam break in, found a couple of small oil pan leaks but all in all pretty satisfied.
|
All times are GMT -4. The time now is 11:57 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com