Re: What did you do to your truck today part III
5 Attachment(s)
Made some progress over the weekend. Sorry about the sideways pictures, any tips to rotating them? They were not sideways on my computer.
|
Re: What did you do to your truck today part III
Quote:
|
Re: What did you do to your truck today part III
Been trying to finish blasting my frame,but keep blowing holes in the ball valve on the blaster hose. Already been through 4 valves in two bags of media. Ordered some stainless steel one today,so maybe next week I will have some new pics. Finally cooling off enough to get motivated. Only problem with that is now its Deer season.lol
|
Re: What did you do to your truck today part III
Quote:
|
Re: What did you do to your truck today part III
Oh I love the progress,just not the heat,lol
|
Re: What did you do to your truck today part III
headlights quit on me Saturday night after leaving a local cruise. So I figured I had better figure it out with Goodguys coming up this weekend in Bowling Green.
Narrowed the problem down to the dimmer switch. Had some high resistance in some terminals. So cleaned them up and did a little solder job. Put it back together and still no luck. I would get power when I pushed down on the switch so I took it back apart. I filled the dimples in the spinner wheel with solder and now all is well. I guess it had worn and created enough clearance that it would not make good contact. http://i771.photobucket.com/albums/x...2017.38.27.jpg http://i771.photobucket.com/albums/x...2017.38.31.jpg http://i771.photobucket.com/albums/x...2017.42.27.jpg |
Re: What did you do to your truck today part III
Quote:
|
Re: What did you do to your truck today part III
Thanks, Probably should have bought a new one, but did not want china junk.
|
Re: What did you do to your truck today part III
RKS NICE work on the PS adapter.
Bruce, I admire your tenacity - fix'n what you got - love it. I just bought a dimmer from NAPA and we'll see how long it lasts. Last night I finished wiring and shrinking all my connections in the home-made harness going aft for lighting and fuel sender. Turned out good. Added ground wires in several places too. Blazer tank filler and vent hose added. Tightened bed mounting bolts and touched up some paint underneath. I'm trying to get it back on the floor so I'm buttoning up everything I can think of underneath! So I installed and ran the speedometer cable my buddy gave me... now to bleed the brakes and sit it back on the tires. |
Re: What did you do to your truck today part III
4 Attachment(s)
Didn't get the brakes bled but I plinked a bit anyway
Turned the re-pop Stock gas tank cover into a back panel, finished my Civic door seals, rebuilt my instrument panel, modified my glove box door. |
Re: What did you do to your truck today part III
Still have yet to bleed the brakes, but I do have doors that close and latch now.
|
Re: What did you do to your truck today part III
Loads of stuff, captured in my build thread.
However, also removed the old steering column..... And tried out the "new" one. Understood to be from a Chevy Day van of unknown vintage. Possibly 80/90's I was wondering if anyone knows what it's cable operated section is for? If you turn the ignition key beack and push it in after turning it to the "off" position, it activates a cable in there, but then you cannot remove the ignition key. This component is in the way where I need to fit the column,so needs to be removed, but I have no idea what it's purpose is. http://i294.photobucket.com/albums/m...psof9kalnh.jpg Advice and help appreciated. Thanks as always. |
Re: What did you do to your truck today part III
I wiped the '66 down with some detailing spray....
...then went and beat on a Ferrari 360 Spider for a while :devil: |
Re: What did you do to your truck today part III
I didn't unload my spare 10si alternator from the vacation car so it came along for the ride to Seattle, BC's sunshine coast, back to Seattle and finally home to Calgary again. This upsets me that I didn't have a place for it so on to the 66 C10 today it went. It only took about an hour and a half including the conversion from externally regulated. The bearings in the old one feel a bit rough so that's a good excuse to drop it off for recycling at a local alternator shop.
|
Re: What did you do to your truck today part III
I rebuilt my first carburetor but by the time it was done I was out of day light . So never got to test it and see if I did it right or not lol
|
Re: What did you do to your truck today part III
1 Attachment(s)
Since switching jobs. I now work in the town I live in :) so I took my new daily driver to work :metal: so pumped to be driving it consistently now.
|
Re: What did you do to your truck today part III
1 Attachment(s)
Officially bolted the '82 C30 front suspension into my '62 temporarily. Installed Hydro Boost onto bracket. Mocked up steering shaft. Stared at rear of frame for an hour contemplating brackets for new fuel tanks. I guess you could say I now have power steering and disk brakes!!
|
Re: What did you do to your truck today part III
http://i615.photobucket.com/albums/t...B2D0A1915B.jpg
Plus http://i615.photobucket.com/albums/t...0528D5516B.jpg And one of these http://i615.photobucket.com/albums/t...DF6B0C69D4.jpg Equals http://i615.photobucket.com/albums/t...0763844CC3.jpg But this http://i615.photobucket.com/albums/t...C71A4ACDD5.jpg Highlights the need for these http://i615.photobucket.com/albums/t.../c%20notch.jpg And possibly http://i615.photobucket.com/albums/t...aul-Y/Bags.jpg As there is probably another 20-30 loads of this. http://i615.photobucket.com/albums/t...B2D0A1915B.jpg One day I will get round to updating what I have been doing and why there is a rather large ‘red rash’ on Woody’s flank. But until then… P. :D |
Re: What did you do to your truck today part III
1 Attachment(s)
Paul Y wins. Truck, chopping wood, beer can never be beat.
All I did was load a small block and th400 into my s10 and brought them home. Small block needs to be rebuilt, so that will be my life for awhile. |
1 Attachment(s)
Almost done with the inside of a bedside, gotta finish welding up the outside Sean from the long to short conversion, the smithing about what coating it's going to get. Rust run is on it now to prevent rust u till I figure out if it's getting por15 and bedliner or...
Posted via Mobile Device |
Re: What did you do to your truck today part III
5 Attachment(s)
Dry fitting the tanks.
|
Re: What did you do to your truck today part III
I likr those tanks...Are they the standard Blazer style tanks?
|
Re: What did you do to your truck today part III
Quote:
Possibly one of the best posts iv seen on this forum in a while. Well don't amight:smoke: |
Re: What did you do to your truck today part III
Thank you Matt, appreciated.
P. :D |
Re: What did you do to your truck today part III
2 Attachment(s)
Got the motor and trans out today. Good thing my boys came to help out. We had a tough time pulling the hoist back into the garage through the gravel. lol
|
All times are GMT -4. The time now is 03:32 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com