Re: Parting this 66
 

Jimmy,

Thanks for photo, could the number be 3923898?

How does the pulley grove/ belt area look?

Thanks,
Les

Re: Parting this 66
 

Yes that could be the number. A little surface rust from sitting and will clean up fine. I can put it in the lathe and clean them in short order.
Jimmy

Re: Parting this 66
 

Jimmy,

PM sent

Les

Re: Parting this 66
 

Sorry I'm late to the conversation .... if you still have this bucket of rust are you willing to cut a donor panel off the cab?? I need passenger side, cab rear corner/back of cab. I can provide more specifics if this is something you are wiling to do. Note: I understand that the bottom rear cab corner is always rotted out ... what I need is kind of from the horizontal body line (mid-height on the cab) to the bottom of the cab from the door jam around to the back of the cab to the place where the back of the cab has the first pressed indent below the back window. Anyway; let me know if this is possible. Thanks, Rod

Re: Parting this 66
 

It left for the scrap yard Saturday.
Jimmy

Re: Parting this 66
 

Dang! Timing is everything! My loss. Thanks,

Re: Parting this 66
 

Looking for a cast iron V-8 manual trans bellhousing. was this an 8 or six? Stick or Auto?

Thanks,
Larry W.

Re: Parting this 66
 

I sold the one in this truck. The bell housings will fit either engine.
Jimmy

Re: Parting this 66
 

Do you have a choke cable and knob?

Re: Parting this 66
 

I may Will look today.
Jimmy

Any luck
Posted via Mobile Device

Re: Parting this 66
 

The only one I could find is about 28" long. It had been cut sometime in its life.
Jimmy

Re: Parting this 66
 

radiator support (core support) still available? shipped to TX 79424?

Re: Parting this 66
 

Bottom was not to good on that one.
Jimmy

Re: Parting this 66
 

Did you buy this out of Texas?? I swear I almost bought this truck because it had a full a/c set up in it but the rest was just parts to sell!

Re: Parting this 66
 

Nope came out of Virginia and had been here all its life. No AC in this one.
Jimmy

Re: Parting this 66
 

not sure how much of the body molding/trim cypher end up taking, but i am looking for ONE piece, I'm missing the upper trim piece on the door. just the one.IF you got one still ill take it. shipped to 89139

Re: Parting this 66
 

I do still have some door pieces. I need to dig them out and see if I have a good one left.
Jimmy

Re: Parting this 66
 

Any engine parts? Like Ram Horns & Power Steering pump and brackets. shipping to 92284

Re: Parting this 66
 

No power steering stuff but I do have a set of 66 exhaust manifolds that came of my truck.
Jimmy

Re: Parting this 66
 

Pic's & $$.$$ would be good, whats both of there Casting Numbers??

Re: Parting this 66
 

that would be great..the pieces I'm working with now are in rough shape as well so it might not be a problem..im not goin for looks, more just completeness lol...please let me know!! its hard to find single pieces around here.

Re: Parting this 66
 

Scum1 I did find a door piece. I cleaned the dirt off and it looks ok. A couple of dings is it. I'll get the picture off my phone in the morning.
CK5566 I got a couple of pics of the manifolds for you.
Jimmy

Re: Parting this 66
 

Pic's are great but whats there Casting Numbers, Thanks

Re: Parting this 66
 

Emergency brake parts? I need the clips, the long rods, the short funky shaped parts and other parts. Basically everything but the cables.