Re: project INCREDIBLE HULK 6.2L with 6L80E
 

Lookin good!

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

Hey don, we have talked before about cruise control. I was looking at the schamtic and the cruise control switch goes to the BCM from the steering wheel controls and then the BCM sends the signal to the PCM via class 2 data. To get the cruise to work with these engines do you need a controler or can you just change the programing in the PCM the see the input from the dikota digital switch. I emailed dikota digital, but they don't seem interested in getting back to me.

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

what year, engine/trans, and computer you running?

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

I am running a 5.3L/4L60 out of a 2007 tahoe.

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

hmmmm, ill see what i can find out...

finished the brake mount/firewall stiffener, and mounted the brake set-up ....its a close fit under the dash but is looking good IMO.....here are the pics.....
http://i25.photobucket.com/albums/c8...k/100_0781.jpg
http://i25.photobucket.com/albums/c8...k/100_0782.jpg
http://i25.photobucket.com/albums/c8...k/100_0808.jpg
http://i25.photobucket.com/albums/c8...k/100_0809.jpg
http://i25.photobucket.com/albums/c8...k/100_0810.jpg

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

I got a piece of the description and operation of the cruise control off of the GM website.

The body control module (BCM) monitors the signal circuit of the cruise control switches. The BCM relays the cruise control switch status to the engine control module (ECM) via the GMLAN serial data circuit. The ECM uses the status of the cruise control switch to determine when to capture and maintain the vehicle speed. The ECM monitors the vehicle speed signal circuit in order to determine the desired vehicle speed. The ECM uses the throttle actuator control (TAC) motor in order to maintain the vehicle speed. For further information on the TAC System, refer to Throttle Actuator Control (TAC) System Description .

I'd post the schmatic but it is to big and if I resize it I don't think you'll be able to see anything.

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

That's a mouthful! :D I have an 06 Tahoe motor and was told by Speartech that they could easily pull the wires for the Cruise to work a standard cruise control arm, FWIW.

R

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

what's the plan for the windshield wiper motor now?

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

conceal it:metal:

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

I just realized, this isnt for a 6.2 Diesel. :(

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

nope....better:lol: :metal:

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

ok, getting this thread back to the top.......the vettes dash was gonna be modded to fit this dash, but after looking at it and measureing the curved peices look good on the vette dash cause its small.....put the same curved peices on a truck dash, and they look small.....so keeping with that look im gonna make my own dash outta metal......so after cutting the dash appart, i welded in a filler peice for the whole dash, then bent up some tube stock round bar......to get the skelaton on the dash.....
http://i25.photobucket.com/albums/c8...k/100_0430.jpg
http://i25.photobucket.com/albums/c8...k/100_0431.jpg
http://i25.photobucket.com/albums/c8...k/100_0544.jpg
http://i25.photobucket.com/albums/c8...k/100_0547.jpg
http://i25.photobucket.com/albums/c8...k/100_0908.jpg
http://i25.photobucket.com/albums/c8...k/100_0907.jpg
http://i25.photobucket.com/albums/c8...k/100_0910.jpg
http://i25.photobucket.com/albums/c8...k/100_0909.jpg
http://i25.photobucket.com/albums/c8...k/100_0911.jpg

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

Would a 61-63 GM truck dash not work for your goal? Seems it would be an easier fabrication.

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

I always look forward to the updates on this build. Cool mods going on!

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

yea, easier, but not quite what we want to do.....

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

Quality work being done here. Keep it up.

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

got some loose ends wraped up, completed the capped wire gutter, and also started to shave the drip rail.....
http://i25.photobucket.com/albums/c8...k/100_0935.jpg
http://i25.photobucket.com/albums/c8...k/100_0936.jpg
http://i25.photobucket.com/albums/c8...k/100_0937.jpg
http://i25.photobucket.com/albums/c8...k/100_0938.jpg
http://i25.photobucket.com/albums/c8...k/100_0939.jpg
http://i25.photobucket.com/albums/c8...k/100_0940.jpg

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

After looking at the picts i don't think we need the round stock...
looks sweet to me!

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

anything new?

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

little bit of progress......working on the dash still here are a few pics, they are a bit dark, but you get the idea.....
i bent the hoop on the end of the center console, then braced the center section, rough cut a peice of metal for the center, and worked myself around useing clekos to hold everything in place......i then plug welded everything, and cut to shape.....ill get some better pics of everything up tomorrow
http://i25.photobucket.com/albums/c8...k/100_1075.jpg
http://i25.photobucket.com/albums/c8...k/100_1077.jpg
http://i25.photobucket.com/albums/c8...k/100_1078.jpg
http://i25.photobucket.com/albums/c8...k/100_1079.jpg
http://i25.photobucket.com/albums/c8...k/100_1080.jpg
http://i25.photobucket.com/albums/c8...k/100_1081.jpg

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

here are some more dash progress pics..
made a templet out of cardboard, transfer it to metal, rough cut it out, trimed it a bit, then clekoed it in place.......and the same for the pass. side.....here are the pics
http://i25.photobucket.com/albums/c8...k/100_1085.jpg
http://i25.photobucket.com/albums/c8...k/100_1086.jpg
http://i25.photobucket.com/albums/c8...k/100_1087.jpg
http://i25.photobucket.com/albums/c8...k/100_1089.jpg
http://i25.photobucket.com/albums/c8...k/100_1090.jpg
http://i25.photobucket.com/albums/c8...k/100_1091.jpg
http://i25.photobucket.com/albums/c8...k/100_1092.jpg
http://i25.photobucket.com/albums/c8...k/100_1093.jpg
http://i25.photobucket.com/albums/c8...k/100_1099.jpg
http://i25.photobucket.com/albums/c8...k/100_1100.jpg

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

very interesting concept... are the window defrost holes not centered on the original dashes? Are you gonna fill them in too?

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

not sure bout the defrost vents being sysmetrical, but they will be filled in and smoothed.....if you look carefully in the center of the dash i have a center line (in red) for my reffrence...

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

Looking nice.

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

that is gonna look amazing

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

Pretty fancy looking. I wanna see more.

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

That is bada$$ :metal: That's what I had in mind for my 61.

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

x2

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

Looks great!

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

got the steering column in, its a ididit tilt, column shift, chrome, one... the mounting positon had to be slighly moved over, do to the underdashed brake setup... to do away with the bungy cord, the upper part of the column mounting bracket was made from a portion of exhaust tubeing..... here is the pics...
http://i25.photobucket.com/albums/c8...k/100_1108.jpg
http://i25.photobucket.com/albums/c8...k/100_1110.jpg
http://i25.photobucket.com/albums/c8...k/100_1111.jpg
http://i25.photobucket.com/albums/c8...k/100_1112.jpg
http://i25.photobucket.com/albums/c8...k/100_1113.jpg
http://i25.photobucket.com/albums/c8...k/100_1116.jpg
http://i25.photobucket.com/albums/c8...k/100_1117.jpg
http://i25.photobucket.com/albums/c8...k/100_1119.jpg
http://i25.photobucket.com/albums/c8...k/100_1118.jpg

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

Ooooh.....It's soooo shiny.......:cool:

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

I have a question about the mount on the fire wall side of the column. Where did ya get it and can it be used on a regular stock column?

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

i got it from summit racing....they are called a steering column bulkhead, the one i got is 2.25" round... but you can get them in 2" diamater too (stock column OD size).

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

Looks like it's coming along nicely.

I'm diggin the dash too.

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

Very cool build. Are the guages going to be retro?

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

nice build

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

The gauges cluster will be from a modern vehicle. Stay tuned!!

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

You sir, exhibit some seriously meticulous craftsmanship. Very nice job!

Re: project INCREDIBLE HULK 6.2L with 6L80E
 

a little update on the hulk, we're trying to get thing a roller....so i got a fo*d 9" and im in the process of narrowing, rebuilding, and smoothing....its gonna be narrowed 8.5" from the stock 12 bolt, or 50" houseing end to houseing end....
anyways here are a few pics
http://i25.photobucket.com/albums/c8...k/100_1194.jpg
http://i25.photobucket.com/albums/c8...k/100_1195.jpg
http://i25.photobucket.com/albums/c8...k/100_1197.jpg
http://i25.photobucket.com/albums/c8...k/100_1198.jpg
http://i25.photobucket.com/albums/c8...k/100_1199.jpg