![]() |
Re: S10 Swap how to
Quote:
|
Re: S10 Swap how to
Quote:
|
Re: S10 Swap how to
Thanks. You too!
|
Re: S10 Swap how to
Quote:
I have been trying to figure this out, and something must be different on my frame. It's a 84 s-10, 117", std cab, long bed. I keep coming up with 34 3/4", not the 33 1/4". Is it possible my older frame had the holes in different spots? |
Re: S10 Swap how to
Quote:
|
Re: S10 Swap how to
54 looks great! Where did you find that flex coupling between the MAF and the intake tube(4" I assume)? Also what did you use for an A/C compressor?
|
Re: S10 Swap how to
Quote:
Front edge of oval hole to rear edge of 5/8 hole, 43 1/4" Add 2 1/8" from oval to rear of front stand, total 45 3/8" Remove 10 1/2" to get to front edge of rear stand 34 7/8" This should be 33 1/4", where did I go wrong. I do understand, tack them on, put cab on, confirm engine space, make corrections as needed, pull cab, finish weld, but I would like to avoid any suprises. Great thread, thanks so much for the help. |
Re: S10 Swap how to
I just tacked the stands on that 84 frame tonight. I took some measurements to verify for you. Rear edge of front stands 2 1/8 forward of the edge of the oval hole. Front edge of rear stand 10 1/2 behind the 5/8" frame hole. From front edge of rear stand to rear edge of front stand is exactly 33 1/4". Not sure why you are getting a different measurement. This one is a long bed rev cab as well.
|
Re: S10 Swap how to
The flex coupling is a stock piece from the donor Suburban. AC compressor is the stock Denso compressor from the suburban, in the stock low mount bracket. The truck uses a stock Silverado belt still.
|
Re: S10 Swap how to
Just getting ready to mount my engine and trany, is there any reason besides cost that you choose to use solid welded motor mounts rather than ones with poly or rubber?
|
Re: S10 Swap how to
I use rubber mounts. 71 Camaro mounts are cheap, and they bolt to the engine. The uprights just replace the stock perches... no way I"d solid mount an engine, makes everything vibrate!
|
Re: S10 Swap how to
I've been surfing the s10 forum for a wile and a guy with a blazer got lengthened front control arms from Michigan metal works. They will cut them to what ever length you want. His cost him $1000 for the set, upper/lowers. I checked out there site and they have really good prices if anyone is looking for control arms. But my question now is what do you or have you done to widen the front track width to match the rear width? Besides spacers.
So far from searching a wile on this, Michigan metal works will be the way I go but would love to hear other people's plans. |
Re: S10 Swap how to
Quote:
I still have not been able to figure out why my measurements for the cab stands don't match yours. I have measured them a couple dozen times in different ways in case I'm reading your notes wrong and can't come up with 33 1/4. There must be something different with my holes, my frame certainly does not match the pictures you have posted, but I figured it was just a variation on the year. I'll just need to put the cab on and make sure there right before welding. Thx again! |
Re: S10 Swap how to
I got this great message today:
I think I figured out your Issue with the cab stand measurements. I am sitting here looking at my bare frame right now. Feel free to give me a call and I will explain what I think is going on. Curt So I called Curt on the phone, we stood at our frames and sure enough my frame does not have the 5/8" hole in the same place as his. Either way, the 33 1/4" between the two cab stands is correct, but not everyone has the rear 5/8" hole. Thanks Curt, I hope to have my fully restored cab on my s-10 chassis by Christmas. |
Re: S10 Swap how to
Quote:
|
Re: S10 Swap how to
Sorry coldshot. I use spacers. A grand for control arms is out of most of my customers budgets. I've built quite a few, and have been driving the 48 for over 2 years. No problems yet.
|
Re: S10 Swap how to
Quote:
|
Re: S10 Swap how to
Quote:
Thanks, thought you might be interested in the info in case one of your customers wants to go that way. |
Re: S10 Swap how to
Quote:
|
Re: S10 Swap how to
Great write up! It will help get more of these old trucks on the road.
I love the steering column part. Im almost ready to set mine up, but my motor is wider than a LS. How do you get the steering shaft around the motor do you have a pic? |
Re: S10 Swap how to
Quote:
http://cdn.airassisted.ca/Bolt-in-Ai...r-Control-Arms Not the cheapest but really strong!! |
Re: S10 Swap how to
Same price as what I'm looking at so not to bad for the full set. If I buy arms tho I want to eliminate the spacers if I can.
I love your build, I can see why you want the super strong arms. |
Re: S10 Swap how to
Lower50's; Thank you. I use a double Borgeson joint set up if the header interferes with steering shaft alignment. With a double setup you will need to capture the shaft near the second joint to keep it from binding. Look at "Rico F. '54 LS build" I have pics in that thread.
|
Re: S10 Swap how to
Thanks Skymangs. That looks good I'll have to set something like that up.
|
Re: S10 Swap how to
Thanks. Pm me if you run into any problems.
|
All times are GMT -4. The time now is 06:38 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com