![]() |
Re: The '67 Burb Build Thread
2 Attachment(s)
no pic of it, but i recieved my porterbuilt panhard bar yesterday, also got my front fender skim coated and sanded down and in filler primer. still have a few small spots to touch up, but its almost done
Attachment 693111 Attachment 693112 |
Re: The '67 Burb Build Thread
lookin good man..
what did you do with your heater hoses after you blocked off the firewall? Posted via Mobile Device |
Re: The '67 Burb Build Thread
what heater hoses? i never had any on it to begin with lol.
|
Re: The '67 Burb Build Thread
i seen this in the wha did you do to your truck thread an commented....
|
Re: The '67 Burb Build Thread
5 Attachment(s)
opened up my porterbuilt panhard bar the man in brown dropped off yesterday. all i got to say is beautiful welds and excellent quality products
Attachment 693558 Attachment 693559 Attachment 693560 Attachment 693561 Attachment 693562 |
Re: The '67 Burb Build Thread
man that looks good! i shouldve went that route with mine..wish you could leave it raw just to show how nice they look original.
im really digging that push button start...have you tried it out yet? |
Re: The '67 Burb Build Thread
haha i know right. yah, i bumped it over but didn't start it up because i have my hood sitting behind my burb, and dont want two black spots on my hood lol. but it woorks good.
|
Re: The '67 Burb Build Thread
2 Attachment(s)
finished grinding down the plate that i cut out to box my lower arms in with, and picked this up for $10 to replace the one in my burb, and yes i know it is for a 67-68 gmc and it is in better shape than mine minus the part where the hood pin thing goes in the center but i will remove that from mine and install it on that one, will probably also gut the handle and move it over or use part of the one from the one it is replacing so that it is not offset
Attachment 694124 Attachment 694125 |
Re: The '67 Burb Build Thread
started the install of my porterbuilt panhard bar, almost done, just need to paint and install the bar
|
Re: The '67 Burb Build Thread
3 Attachment(s)
finished installing the pb panhard bar:metal:, just need to adjust it. also removed the rear lower bag mount and cut out the cross bar that i had put in it that wasnt strong enough and was bent. will be replacing that with some dom tubing.
Attachment 695423 Attachment 695424 Attachment 695425 |
Re: The '67 Burb Build Thread
it must be a pain to jack up somthin this low
|
Re: The '67 Burb Build Thread
lol. if the suspension is aired up it isnt a problem, but this time it was because my dads little compressor took a dump, and it was sitting on the ground. good thing i have no floor in the back haha. but still was a pain in the a$$, and took forever. had to use 2 bottle jacks and some 2x4's just to get it high enough to get the floor jack under it from the side as i couldnt get to the back of it either.
|
Re: The '67 Burb Build Thread
dayum!
|
Re: The '67 Burb Build Thread
hahaha thats what i said when the compressor took a dump. guess i need to invest in a good portable one or something for now lol.
|
Re: The '67 Burb Build Thread
:lol:
|
Re: The '67 Burb Build Thread
try jacking the truck up when its dumped, with flat tires, and in the grass! talk about a pita!!
|
Re: The '67 Burb Build Thread
haha no thanks, but at least you can get to the back lol.
|
Re: The '67 Burb Build Thread
ņo offense at all but this is one reason why i am glad my six seven isnt lowered.....:lol: all though i might end up lowering it a little.....time will tell.....
|
Re: The '67 Burb Build Thread
haha its ok, the only reason why i had such a hard time is because i couldnt get to the back lol.
|
Re: The '67 Burb Build Thread
4 Attachment(s)
adjusted the pb panhard bar and threw a quick crappy paint job on my glove box door will redo it better later. and took a couple of pics of the clearance of the pb bar and brackets just perfect lol. and also took a pic of the part of the rear brake line that i can see from underneath.
Attachment 695923 Attachment 695924 Attachment 695925 Attachment 695926 |
Re: The '67 Burb Build Thread
wow that dash is clean! i need to find an A/C 67 dash so i can do a conversion to A/C
|
Re: The '67 Burb Build Thread
haha thanks, it looks cleaner in that pic than it really is, i need to do the bodywotk to the center section but that will not be happening right now. will save that project for late.
|
Re: The '67 Burb Build Thread
do you already have the a/c stuff for inside the dash? (center vent and other vent)
|
Re: The '67 Burb Build Thread
nope, what you see is what i got, other than one vent ball and part of the center vent(the directional piece), why you got some stuff laying around i can have lol??
|
Re: The '67 Burb Build Thread
a driver side peice it is blue and it is the outer peice that screws in the dash....
|
Re: The '67 Burb Build Thread
haha i already have those 2, oh well lol.
|
Re: The '67 Burb Build Thread
haha oh
|
Re: The '67 Burb Build Thread
5 Attachment(s)
not a whole lot but i repainted my gauge bezels and started installing them in the cluster. now i need to buy the rest of the gauges so i can finish it, and also make/cut out a piece so i can install my gas gauge and turn signal lights in the cluster.
Attachment 696315 Attachment 696316 Attachment 696317 Attachment 696318 Attachment 696319 |
Re: The '67 Burb Build Thread
1 Attachment(s)
|
Re: The '67 Burb Build Thread
looks good eric! you should do around the cluster and around the glove box door with the silver.......just my .02
|
Re: The '67 Burb Build Thread
thanks. nah that would be to much of a pain in the butt, and i dont want to much bling lol.
|
Re: The '67 Burb Build Thread
not much of an update, but i installed the sunvisors back in the burb
|
Re: The '67 Burb Build Thread
5 Attachment(s)
not much of an update on the burb but i did pick this up out of a jeep for it lol. and also picked this up for my beetle for $100. :metal:
edit: also purchased a 3rd door sill plate from sharpie Attachment 697294 Attachment 697295 Attachment 697296 Attachment 697297 Attachment 697298 |
Re: The '67 Burb Build Thread
i have said it once and i will say it again sharpie is the man!!!
|
Re: The '67 Burb Build Thread
hell yah he is, super great guy to do business with, actually done business with him a few times so far after the buying the hinge. and he was actually gonna send me another 3rd door lower hinge at no cost because usps took like 2 weeks to deliver it, and nobody knew where it was lol, but it came just before he was getting ready to send the other one out.
|
Re: The '67 Burb Build Thread
see ther ehe goes amazing me again! me and him are definatly gonna be dealing with each other for a while!
|
Re: The '67 Burb Build Thread
haha thats why i bought more stuff from him lol. lets see, so far the hinge, then some headlight/wiper knobs and chrome bezels, and now the sill plate. hmmm what next lol.
|
Re: The '67 Burb Build Thread
WE LIKE HEIM JOINTS..............YES SIR DO IT TO IT:metal:
Quote:
|
Re: The '67 Burb Build Thread
HAAAAA not a problem at my house my burb is "overbodydropped" meaning my frame is still 3-4" off the ground when flat out down,,,,just roll the jack (lo pro jack, of course) between the wheel well and tire,,,jack it up *piece a toast*
Quote:
|
Re: The '67 Burb Build Thread
no pics yet, but i finished welding and boxing up the lower a arms, need to do some grinding and some wire wheeling, and drill a couple holes for the bags, then i can paint them and start putting them together. sure hope i can get the ball joints out of my other a arms without damaging them.
|
All times are GMT -4. The time now is 02:14 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com