Re: Project Vitamin C-10
Quote:
|
Re: Project Vitamin C-10
thanks i just joined now im waiting to be approved
|
Re: Project Vitamin C-10
Quote:
|
Re: Project Vitamin C-10
Quote:
Quote:
Got the Mar-K inner bedside patches installed on one bedside plus I also did a couple other patches. The patches were great and are one of the easiest patch panels you will ever do. Did some measuring to determine where to make my cut and got the patch clamped in place. http://i606.photobucket.com/albums/t...d/DSC01745.jpg Installed the wheel house to make sure everything is lined up. With it clamped in place will help hold everything in place. http://i606.photobucket.com/albums/t...d/DSC01746.jpg http://i606.photobucket.com/albums/t...d/DSC01747.jpg Completed http://i606.photobucket.com/albums/t...d/DSC01748.jpg Had to make and replace the short angle. I made it out of some good metal that I just cut out for the patch. That way I would have a good square hole to go in the corner. It's hard to get a drill in the corner later when I test fit everything. http://i606.photobucket.com/albums/t...d/DSC01749.jpg I used some old metal from a scrap door to make a patch. http://i606.photobucket.com/albums/t...d/DSC01750.jpg I reversed the bend. http://i606.photobucket.com/albums/t...d/DSC01751.jpg Held it in place with self tapping screws to create a template. http://i606.photobucket.com/albums/t...d/DSC01754.jpg Getting it lined up. http://i606.photobucket.com/albums/t...d/DSC01755.jpg I knotched mine here. Others will do it differently, but worked well for me. There was too much going on in one location. The lap, corner and bolt hole were all too close together. I chose to space things out a little. There is a lower bolt hole to use for alignment. http://i606.photobucket.com/albums/t...d/DSC01757.jpg more on next post |
Re: Project Vitamin C-10
http://i606.photobucket.com/albums/t...d/DSC01763.jpg
Done welding just need to grind. http://i606.photobucket.com/albums/t...d/DSC01764.jpg |
Re: Project Vitamin C-10
Nice work Alan! I have a couple panels to patch i will just send them on over since you already have your tools out and warmed up ;) :lol:
|
Re: Project Vitamin C-10
and of course it looks perfect
alan you make this look so easy:metal: |
Re: Project Vitamin C-10
Very nice.:metal:
|
Re: Project Vitamin C-10
Quote:
Quote:
I'm thinking about cutting my own wood for the bed. The only thing I haven't built on this truck is the rearend and trans. I might pay someone to install the windshield just because of the breakage factor. I think it will still classify as home built.;) |
Re: Project Vitamin C-10
very nice work Alan
|
Re: Project Vitamin C-10
Quote:
There are somethings that I let the more qualified people in know do for my stuff. Trans work, Engine short block machine work and assembly, rear gear set up, seat upholstery, winsheild install (for the same reason you mentioned)...you know, the things that I don't have the correct tools for... Looking good, ALAN! |
Re: Project Vitamin C-10
This is and has been an amazing adventure and undertaking. Thanks for the effort you put into yours. Its helps us all feel that we can do more.
|
Re: Project Vitamin C-10
Hands down, Alan - best build thread so far. Detail is incredible and it's easy to see the care taken in thinking the process out. Thanks again for the effort.
Mac. :mm: |
Re: Project Vitamin C-10
Great job Allan. You do make it look easy, but we know it's not. :metal:
|
Re: Project Vitamin C-10
I second everyone above, great job, and yes you make it look so easy! Looking back I wish I would have used patch panels myself instead of welding in just an bottom angle but no dineros lol. And as always many thanks for the pictures and write up.
|
Re: Project Vitamin C-10
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
I checked on line with homedepot for wood. A 1X8 red oak is $4.10/linear foot. I figured the cost with tax to be around $350. There are only 2 boards of the 10 runs that a 1X6 wood work, so I just figured all 10 runs at 8" wide. I will contact some cabinet shops to see what their cost would be. If there isn't much difference in price why not just buy them pre made, other than just the satisfaction of doing it yourself. |
Re: Project Vitamin C-10
Yes sir thats what I call progress... Good work man.
|
Re: Project Vitamin C-10
Alan your my hero, when I grow up I wanna be just like you. LOL
Keep it up man I enjoy reading about all your good tips. |
Re: Project Vitamin C-10
Quote:
|
Re: Project Vitamin C-10
Quote:
Quote:
Quote:
Finally got around to cutting up a tree that my dad cut down in the spring. Everyone needs a great neighbor like Shannon. I told him I was splitting wood and he was over in no time. Good thing I hand a rand handed axe. :lol: Had to get an action shot. http://i606.photobucket.com/albums/t...2/DSC01804.jpg I found a new sand blaster/powder coater 8 miles from the house. Anyone in the area needs to check him out. He has a great place with great equipment. Custom Powder Worx ask for Ervin @ 404-216-4230. He has a big oven to powder coat frames. Tell him I referred you. I get nothing off of it. I asked him if it would be ok if I put his info here, since he doesn't advertise. He is about 5 miles off exit 27 on I-575. |
Re: Project Vitamin C-10
Still watching and checking in daily... The 51 and I are looking for a little adventure... Thinking about taking a little ride up when things slow down a bit..(nothing like inviting myself up!)
Keep up the great work, I have learned a lot from your thread.. |
Re: Project Vitamin C-10
Quote:
At the Texas Classic Car Show in Austin this weekend a guy had an F100 with a Granite bed. It was definitely different. Unfortunately it was in the last row we looked at and everyone was bugging me to leave, so I did not get a photo. :waah: |
Re: Project Vitamin C-10
GRANITE!!!
that must have been heavy |
Re: Project Vitamin C-10
http://i606.photobucket.com/albums/t...2/DSC01804.jpg
i need some firewood, i will be up there soon to pickup some shannon. LOL hope all is well up there! Sorry i havent gave ya'll a shout in a while been busy at work. |
Re: Project Vitamin C-10
Quote:
Quote:
Quote:
Quote:
I forgot to mention before that I left my hood and grill at the sand blaster |
All times are GMT -4. The time now is 10:06 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com