Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Finished up my coolant hoses, they held 24 in. of vacuum, so that system is good. They wanted 5 gallons of gas to prime fuel system, so I guess he is getting ready to start it up... pics didnt work so youll have to take my word lol
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
Thanks for following all these years, lol seems like I've gotten more done in the last few months, then I did last winter |
Re: PO has me PO'd
OK, today was fuel system, not uneventful, started to put 5 gallons in it, gas can leaked, fixed that and 1/2 gallon went on his floor. No clamps on fuel filler hose, fixed that and put 5 gallon in. Started up the fuel pump and 3 injectors leaked, I'll take the blame for that! pulled the fuel rail, to inspect all the O-rings, installed new o-rings where needed, with a super grease he uses, reinstalled fuel rail w/injectors and it leaked at the fuel gauge, took off my liquid filled gauge and just used shrader valve. adjusted fuel regulater to 50 psi, did some math on his phone, and calculated that I had the right injectors (22 lbs) NO LEAkS
now, just have to figure out why the gauge leaked Had to wash all my clothes as soon as I got home |
Re: PO has me PO'd
OK, so today was exhaust passenger side, needed to be done to put o2 sensor bung in.
Used the factory style separate gaskets, no sealant. Thought I might have a match issues since I have Vortec heads, but using gaskets as a guide, they matched up perfect, forgot my torque wrench, so I'll do it tomorrow when I do the drivers side. Did run into one issue, of course, the placement of the trans temp. fitting is close to the exhaust pipe, need to relocate, drop pan and find a better location https://live.staticflickr.com/65535/...349ba3fc_c.jpg[url=https://flic.kr/p/2hDdTRq]20191031_141442 https://live.staticflickr.com/65535/...8e943d6e_c.jpg[url=https://flic.kr/p/2hDhHtx]20191031_141511 found out why they put that bend in the frame fifty years ago... so I could use my march electric water pump mid alternater mount and swing it to get enough tension on the belt.lol |
Re: PO has me PO'd
did see this bracket on a camaro, that I want to make for my hood pins
https://live.staticflickr.com/65535/...574fb561_c.jpg[url=https://flic.kr/p/2hDhHrd]20191031_124125 |
Re: PO has me PO'd
So, yesterday was trans. cooling lines, didn't think they would fit since I changed the cross member. Cut them in half and offered them up, seems they might have fit after all, but for now, I'll just add a piece of rubber hose and clamps. I'll deal with a better fix when I get it in my shop. Seems like we could be close to making noise ( His term)
I may just plug up the trans pan and deal with it later, since it is stopping me from firing up the motor. These guys have been great to work with, fun shop, with lots of banter back and forth. Dale is just a wealth of information, nice to have someone to bounce your ideas off of and keep me on topic (just focus on what needs to be done to get the engine to run) |
Re: PO has me PO'd
https://live.staticflickr.com/65535/...15ee75e6_c.jpg[url=https://flic.kr/p/2hFLei7]Screenshot_2019-11-05-17-09-54.jp
got to play with my trans. cooling lines today, didn't think they would fit, so I cut them in half, plan to use compression fittings in 5/16" size, my only problem was my splice was right above my crossmember, made it difficult to work on start by finger tight, then put a wrench on it after your sure the threads are started correctly getting ready to make some noise, working on trans. pan as first attempt was wrong. weldable bungs should be here tomorrow, then I can put in sender for the trans. temp unit, and drain plug |
Re: PO has me PO'd
second attempt, still wrong as it is in the way of the front drive shaft, now I'm looking at forward or rearward location, we'll see on monday how it works out
Dale told me to keep plugging away, and we should end up being finished at the same time, as I move forward on the brakes and drive shafts, he wants to drive it out of his shop |
Re: PO has me PO'd
https://live.staticflickr.com/65535/...3917e0f9_c.jpg[url=https://flic.kr/p/2hKo2sg]Screenshot_2019-11-13-15-45-22.jpg
paint later, drive shaft installed, what a PITA the 4 bolts to the CV joint, upside down and backwards. had to drop exhaust pipe for clearance to work https://live.staticflickr.com/65535/...9574847f_c.jpg[url=https://flic.kr/p/2hKo2sG]20191113_133528 seems the forward location was best for the trans. temp. sender, maybe use the bungs for cooling lines later, at least I have a drain plug or two https://live.staticflickr.com/65535/...0c2aefd3_c.jpg[url=https://flic.kr/p/2hKo2EA]20191113_133617 trans. cooling lines done, fill her up with fluid. picked a rather difficult spot to make splices, right above crossmember Now, to work on brake lines |
Re: PO has me PO'd
That home stretch always feels like a long one....
|
Re: PO has me PO'd
Quote:
Yours came out awesome, some miner set backs, but you worked through them |
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Today was a rare exception, everything went right. Double flare on the rear axle worked first time, brakes are done, and clamped to the frame rail with totally stainless 3/16" clamps. I'll let them bleed them. 5th or 6th time on the power steering belt tensioned up today, both belts are now done. Just waiting on some parts I lost (u-bolts) for the drive shaft, and PTO cover plate gasket, both found locally. rear diff. cover sealed up, and both shocks are mounted
also mounted the remote tank for the hydro boost https://live.staticflickr.com/65535/...e8534db2_c.jpg[url=https://flic.kr/p/2hNX7r6]20191121_121327 Now its time for some R&R, thanks giving then a florida trip for a week, hope the fish are biting, and not the bugs Balls in Dale's court |
Re: PO has me PO'd
https://live.staticflickr.com/65535/...25c5b062_c.jpg[url=https://flic.kr/p/2hNW6uC]20191121_121427
|
Re: PO has me PO'd
lookin good......
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
My last flare, I was laying on my creeper upside down and backwards, not seeing clearly as my bifocals were coming in and out of range, working in the dark with a little flashlight, afraid to unclamp the flaring tool. but to my surprise as I brought it down and looked, it was perfect, sometimes you just get lucky. This truck has fought me every step of the way for over twenty years. This the first day that I have not gone to a shop, or thought about it, in some fashion for that long of a time. I will never modify a project again! Yeah right, my mind is now drifting to installing a LS engine in a TR-6. That is where my roots started, early english sports cars But, thanks for stopping by and your kind words, whats up with you and your next project after your break |
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
never liked the doors on an AC Cobra, plus my workshop is too small for trucks LOL Plus tr-6's have flat panels on the bonnet and rear deck to widen the body Yeah, I'm a glutton for punishment |
Re: PO has me PO'd
found some oem parts that I lost in my basement at my local 4X4 shop
https://live.staticflickr.com/65535/...899e782d_c.jpg[url=https://flic.kr/p/2hQPiZX]20191125_132123 |
Re: PO has me PO'd
https://live.staticflickr.com/65535/...d2b6254b_c.jpg[url=https://flic.kr/p/2hXai2X]20191209_122114
https://live.staticflickr.com/65535/...2cd41f3a_c.jpg[url=https://flic.kr/p/2hXahYa]20191209_121959 https://live.staticflickr.com/65535/...2b855289_c.jpg[url=https://flic.kr/p/2hXahX8]20191209_122025 https://live.staticflickr.com/65535/...eefa7fe8_c.jpg[url=https://flic.kr/p/2hXai5T]20191209_122136 |
Re: PO has me PO'd
When I returned from Florida (83 degrees and sunny all week) This what Dale had accomplished. I finished the work on the drive shaft and PTO cover. Now I have to build a bracket for the trans dip stick since it sits to close to the firewall
found out that 2 of the holes are blind, in the T/C so, had to come up with a 1/4" shorter bolts, they are the 2 bolts towards the drive shaft He doesn't like to mount the air temp. sensor in the plenum as it will see heat and throw off the readings, so, later on I will mount it in the air cleaner somehow |
Re: PO has me PO'd
Its alive
|
Re: PO has me PO'd
Yay!!!
|
Re: PO has me PO'd
Congrats, it has to be a great feeling
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
:metal:
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Yea, X2 on that. How about a rip down the freeway!:devil:
|
Re: PO has me PO'd
Excellent Jim.
|
Re: PO has me PO'd
fantastic.......
|
Re: PO has me PO'd
|
Re: PO has me PO'd
|
Re: PO has me PO'd
yeah, she leaks alittle, and has some wierd rattles, and shakes, but give me some time and she'll be on the road
Thanks everyone for following this epic build, and your input over the years, it's been real first video, touch the screen |
Re: PO has me PO'd
That is awesome Jim. Congratulations!:metal:
|
Re: PO has me PO'd
Quote:
|
All times are GMT -4. The time now is 05:04 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com