Re: What did you do to your truck today part III
After a lot of blasting, sanding , tearing apart, sprayed two coats of epoxy and two coats of urethane primer on the cab today.http://i192.photobucket.com/albums/z...psu4naig8i.jpghttp://i192.photobucket.com/albums/z...psj6khpkre.jpghttp://i192.photobucket.com/albums/z...psheljvyxu.jpg
|
Re: What did you do to your truck today part III
|
Re: What did you do to your truck today part III
1 Attachment(s)
Got the bed flipped right and starting the wood install over the next week.
|
Re: What did you do to your truck today part III
Got the front brake lines fabbed up and installed.http://i192.photobucket.com/albums/z...ps6bfltx4c.jpg
|
Re: What did you do to your truck today part III
1 Attachment(s)
Got the tub in and called it a night.
|
Re: What did you do to your truck today part III
|
Re: What did you do to your truck today part III
1 Attachment(s)
I installed my new tailgate! Finally GMC in all 4 corners.
|
Re: What did you do to your truck today part III
3 Attachment(s)
I tried this aqua color today to see if I like it better than the red or flat black ?
im going to strip all the paint off the truck when I do all the body work . |
Re: What did you do to your truck today part III
1 Attachment(s)
Made a throttle rod and installed a radiator overflow.
|
Re: What did you do to your truck today part III
1 Attachment(s)
Got the first placeof the boards mounted
|
Re: What did you do to your truck today part III
1 Attachment(s)
I got my new shocks installed and started on the front shock relocation mounts.
|
Re: What did you do to your truck today part III
Quote:
|
Re: What did you do to your truck today part III
5 Attachment(s)
I media blasted and then applied primer to some engine parts. Not very exciting but it is progress.
|
Re: What did you do to your truck today part III
Last weekend.......
Split motor and trains. http://i294.photobucket.com/albums/m...shiegqgjv.jpeg Useful tool...... Keeping things together. http://i294.photobucket.com/albums/m...sum0uxv1j.jpeg Yup.... Four bolt. http://i294.photobucket.com/albums/m...snbd5iv3s.jpeg Camel hump heads, missing most valve stem seals, one valve damaged and a spring broken. http://i294.photobucket.com/albums/m...stpjn4xg2.jpeg http://i294.photobucket.com/albums/m...smlym1lh5.jpeg Still trying to figure which parts to replace, or just how much new stuff to add. http://i294.photobucket.com/albums/m...snmqpo3ab.jpeg Needs a clean and paint as well. http://i294.photobucket.com/albums/m...sscv2uoz5.jpeg |
Re: What did you do to your truck today part III
1 Attachment(s)
I made room in the garage so I could remove the windshield and change the gasket. It had a split at the bottom and water would come into the cab when driving in the rain. Here they are a nestled in. :chevy:
|
Re: What did you do to your truck today part III
5 Attachment(s)
First picture shows how the old owner used roofing tar to patch a hole or something. When it rained the water would come in and spill on the dash and the floor. Surprised there isn't more rust. You can also see the split at the bottom. The gasket also melted back into petroleum form which also melted onto the dash and I think it protected it from the water and it was rust free so I had to clean all that up and after doing so I sanded some of the surface rust off and coated it with Duplicolor Truck Bed liner.
|
Re: What did you do to your truck today part III
1 Attachment(s)
I also took my automatic steering column apart and repainted it. Don't know if I will stick with the color or not.
|
Re: What did you do to your truck today part III
I took my wheel off to adjust my front brakes and after about 5 blocks of driving it is pulling right again.
Time for disc. |
Re: What did you do to your truck today part III
1 Attachment(s)
Got more wood........😚
|
Re: What did you do to your truck today part III
Quote:
|
Re: What did you do to your truck today part III
Quote:
|
Re: What did you do to your truck today part III
Well, the VHT Chevy orange engine paint went on without a hitch.
Good preparation, cleaning three times over and some head in the steel meant good adhesion. Rattle cans work well if you,are patient and keep the distance equal on every pass. http://i294.photobucket.com/albums/m...sdpyi1vn2.jpeg Result, three coats on flat surfaces, more on the bends. http://i294.photobucket.com/albums/m...sczlxtxya.jpeg Masked up and cleaned block painted too. http://i294.photobucket.com/albums/m...shpwxipfj.jpeg Very pleased with the results of today's work. Almost 01.00 now, so bed time I would think. Final pic just for Greg "Bomp" in Kaiser, Oregon........... There you go my young friend. http://i294.photobucket.com/albums/m...sgdudz8h3.jpeg |
Re: What did you do to your truck today part III
1 Attachment(s)
All the boards in to dry fit so we can mark the holes for drilling. I think I see light at the end of the tunnel...
|
Re: What did you do to your truck today part III
I have been making new dash and console panels for my 65 C10- it has a custom dash thanks to my efforts years ago to lighten the truck up for bracket racing. I will post a picture after the dash is back together. Today I primed the panels. Monday I hope to paint them satin black.
I also painted the upper A arms for my 66 C30- I pulled them and cleaned them up back on New Years. I also started disassembly of the LWB fleetside bed I bought for the C30. |
Re: What did you do to your truck today part III
Quote:
|
All times are GMT -4. The time now is 09:42 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com