Re: My 50 roadster pickup build
1 Attachment(s)
Sorry I didn't post yesterday, friends over.
Here I have removed paint from left rear fender, ready for hammer and dolly work. |
Re: My 50 roadster pickup build
1 Attachment(s)
After getting the metal close as I could. I had removed all the old crap from the inside of fenders, blasted and coated with encapsulator paint.
|
Re: My 50 roadster pickup build
2 Attachment(s)
Pic 1 This is the fender after a little filler, primer sanding and reprimer.
Pic 2 Both rear fenders ready for paint. |
Re: My 50 roadster pickup build
2 Attachment(s)
Pic 1 This is the final layout of my console. Got the radio and AC control openings cut and units installed.
Pic 2 Another view. |
Re: My 50 roadster pickup build
Need to tell a little story here. I'm no different than most home builders on here, things get in our way and work on our trucks take a back set. At this point I was about 1-1/2 years into the build. The next 5 months hardly anything got done. This will happen a couple of times during my build, just wanted everyone to know, no build goes as smooth as we want. Jim
|
Re: My 50 roadster pickup build
4 Attachment(s)
Pic 1 Here I have installed Alan Grove brackets and installed the alternator and compressor.
Pic 2 Started running AC lines and heater hoses. Spent hours trying to figure out the right layout (don't think I ever did). Pic 3 Fabing the hard lines for the fuel system. Pic 4 Inside view of bulk head and AC lines. |
Re: My 50 roadster pickup build
3 Attachment(s)
Pic 1 Starting to fab up my exhaust system, mandrel bends from J.C. Whitney.
Pic 2 For over rear axle. Pic 3 Making up hangers and fitting to mufflers (stainless steel Borla). |
Re: My 50 roadster pickup build
2 Attachment(s)
Pic 1 From header back toward mufflers.
Pic 2 From mufflers to the end of pipes. |
Re: My 50 roadster pickup build
A couple years, YES YEARS later, they were taken apart. I drove to HPC in Oklahoma City, observed their parts check in system. Toured their facility and left my parts to be coated to match my headers.
Well thats today's post. Next post is on the aluminum lift off top. If I get clear I may post that later today, no promises. Jim |
Re: My 50 roadster pickup build
1 Attachment(s)
Quote:
|
Re: My 50 roadster pickup build
Quote:
|
Re: My 50 roadster pickup build
Quote:
|
Re: My 50 roadster pickup build
Quote:
|
Re: My 50 roadster pickup build
1 Attachment(s)
I will break it down from the top of latch to the bottom of cab. The latch is mounted upside down so that it works as a push up (an not a pull down) latch.
|
Re: My 50 roadster pickup build
1 Attachment(s)
Sketch 1 shows the top part that is attached to the bear claw latch arm. I welded a 1/4X20 bolt to the latch arm, then I added a 1/4X20 nut, then an eyelet fitting, another 1/4X20 nut. A 1/4X20 threaded rod also screws into the bottom of the eyelet fitting that will go thru the pipe in the cab body.
|
Re: My 50 roadster pickup build
1 Attachment(s)
Next you will need to thread a 1/4X20 nut up on the threaded rod. Find a location for mounting a brake line holder (mine is on the exhaust tube brace). Mount that holder so the nut rest on top of holder. This will allow you to keep the latch arm in a netural position, when door is closed (see sketch 2).
|
Re: My 50 roadster pickup build
1 Attachment(s)
Depending on where you want to mount your inside lift handle will determine how far you thread the tee fitting up on the threaded rod. The tee fitting is made out of two 1/4X20 1" long nuts (you can get this at the local bolt place). Weld one up to the face of the other to form a tee (see sketch 3 "A". Add 1/4X20 threaded rod to length and put knob on the end.
One you have a location for the threaded rod, drill a hole in the cab corner, large enough for your pipe, and weld to cab. Insert threaded rod thru the pipe, and cut to length, and add the knob (see sketch 3 "B"). |
Re: My 50 roadster pickup build
2 Attachment(s)
Pic 1 shows my inside lift handle, near floor, easy to reach while in the seat.
Pic 2 shows the knob at the bottom of the cab corner coming thru the pipe. Push up and the door opens. |
Re: My 50 roadster pickup build
With everything in place adjust the nuts at the latch to have a little play between the eyelet, once you have everything lined up and working, put red locktite on all the nuts to keep them from moving. If anyone wants more just PM me and we will work in out.
Be back in a few for my regular daily post. Jim |
Re: My 50 roadster pickup build
1 Attachment(s)
Had not worked on pickup for about 4 months, helping friends with their rides, etc. Anyhow, I fabed up a wooden structure to mock up the roof. Here the wood is covered with white poster board. Gave me a good look at how the top might be.
|
Re: My 50 roadster pickup build
3 Attachment(s)
Here are three views of the wood structure, nothing fancy, just for mockup.
|
Re: My 50 roadster pickup build
1 Attachment(s)
Somewhere during this time I had also worked on the hood, primered and installed.
|
Re: My 50 roadster pickup build
1 Attachment(s)
Started making up the aluminum angle across top of header.
|
Re: My 50 roadster pickup build
1 Attachment(s)
Bent the 3/4" x 3/4" aluminum tubing to match the outside shape of cab.
|
Re: My 50 roadster pickup build
1 Attachment(s)
Here I have bent the aluminum tubing to match the shape of main upright support.
|
All times are GMT -4. The time now is 05:03 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com