![]() |
Re: My 63 Project
So it looks like mine is already tapped.
|
Re: My 63 Project
Yup....that's it. So jus get the stud an insert it and your in business.
|
Re: My 63 Project
4 Attachment(s)
Well yes, maybe.....
When I dropped my engine in, the mounting spot for the pivot ball on the block was nowhere near where the throwout arm needed it to be. I had to make this small adaptation to get mine to work: This was all on page 24 of my build if you need to take a look at it.... Attachment 1264580 Attachment 1264583 Attachment 1264586 Attachment 1264594 Good luck, hope it all lines up for you :metal: |
Re: My 63 Project
Just a quick video to show today's progress...
https://www.youtube.com/watch?v=OUQB...ature=youtu.be |
Re: My 63 Project
1 Attachment(s)
It fits!!!
|
Re: My 63 Project
1 Attachment(s)
So the weight of the motor has squatted the front end down pretty low. I may have to go back to full springs.
|
Re: My 63 Project
I measured the lower control arm, 4 inches off the ground.
Tomorrow, getting the doors and windows back together. |
Re: My 63 Project
1 Attachment(s)
So very typical, when you have the time, no money, when you have the money, no time.
On top of that, it's just been so dang hot to work. But, I got some jewelry in. |
Re: My 63 Project
1 Attachment(s)
Not too bad to install. Much only question, the horizontal weather strip at the bottom of the window, does that go on the outside of the strip on the back of the door??
|
Re: My 63 Project
1 Attachment(s)
And the drivers side.
|
Re: My 63 Project
1 Attachment(s)
So I ordered this serpentine setup today. Should look good.
|
Re: My 63 Project
1 Attachment(s)
Transmission cross member being mocked in. Going to have to do some adjusting though as the shifter linkages might hit the cross member.
|
Re: My 63 Project
1 Attachment(s)
Time to fix this hole in the cowl where the spotlight came through.
|
Re: My 63 Project
1 Attachment(s)
Getting the plug in was a challenge.
|
Re: My 63 Project
1 Attachment(s)
Weld it up, grind it, and then some filler. Should be good when I am done.
|
Re: My 63 Project
1 Attachment(s)
Workin on the gas tank today.
|
Re: My 63 Project
1 Attachment(s)
Little bit of color on the calipers.
|
Re: My 63 Project
1 Attachment(s)
And the calipers back on.
|
Re: My 63 Project
1 Attachment(s)
This should look good!!
|
Re: My 63 Project
1 Attachment(s)
Small problem with one of the mounting holes on the power steering pump or this job would be done.
|
Re: My 63 Project
1 Attachment(s)
Better picture.
|
Re: My 63 Project
1 Attachment(s)
LED.turn signals. The chrome cleaned up very nice.
|
Re: My 63 Project
1 Attachment(s)
Headlight beauty rings. Before and after.
|
Re: My 63 Project
1 Attachment(s)
The rings had been painted black and then silver. But they cleaned up.
|
Re: My 63 Project
Are the headlight bezels steel or aluminum? They cleaned up nicely!!!
Vent assemblies look great also. Who did you order them from? |
All times are GMT -4. The time now is 04:37 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com