My 52 GMC Build
 

I have always wanted a early 50's GMC P/U and 8 years ago I found it, A 1952 GMC 9700 that used to be a fire truck in great shape. Just cab forward no motor or trans, but all I wanted was the body to make a hot rod.

Re: My 52 GMC Build
 

Took the 52 cab off the frame. Bought a 1989 s-10 extended cab P/U for the frame only stripped it apart sandblasted frame and primed. Then mounted cab to S-10 frame, there it sat in my garage for 6.5 years. In that time I was planning what I wanted to do.

Re: My 52 GMC Build
 

Spring of 2013 I was ready to start on my 52. The truck had been built in my head for some time now, even drove it in my dreams a few times. As some of you can relate i'm sure. I wanted to make it different in most ways but wanted it to look like a 52 GMC P/U

Re: My 52 GMC Build
 

I can't wait for the next chapter!

Love having the photos.

Re: My 52 GMC Build
 

My neighbor gave me the a motor, trans and axle from a 1994 e350 cube van. I wanted to put a diesel motor in, so this was perfect. 7.3L IDI International diesel. So first step clean up motor and build it to take what I wanted to do to it, then mount it in the frame.

Re: My 52 GMC Build
 

I wanted air bags on all corners to get running boards on the ground. D.O.M. tubular A arms should take the weight of the 1000 lb motor .

Re: My 52 GMC Build
 

I boxed in the frame and added a cross member just behind the cab. I built the transmission with some upgrades and shift kit so it can take the extra hp and tq .

Re: My 52 GMC Build
 

Then I rerouted the exhaust to add a turbo to my N/A motor the plan is inter-cooled 15-20 psi should give me 300 HP and 500 LB/tq

Re: My 52 GMC Build
 

Cab mounted on frame with trans. hole cut. Then I got the cab sand blasted and primed

Re: My 52 GMC Build
 

Then the plan for the rear end is to run the dually from the cube van with car tire. But I still want to keep the P/U look so it is out right now to get shortened 21". I am going to build the back half of the frame, also triangulated 4 link with air bags.:metal:

Re: My 52 GMC Build
 

wow !

Re: My 52 GMC Build
 

That's all I have now till the axle comes back. I'm doing most of the work myself, with a bit of help now and then from friends. It's also all seat of your pants engineering.

Re: My 52 GMC Build
 

NICE< Real NICE !!!:metal::metal::metal:

Re: My 52 GMC Build
 

Great project, and cool build. I can tell you from expreience, don't give that 7.3 more than 14psi of boost or you will get good at swapping engines. You need to install bigger wrist pins to go above 14psi of boost. They're great engines besides that little deal.

Re: My 52 GMC Build
 

What a cool project, I will watch this to the finish if you keep the pics coming.

Re: My 52 GMC Build
 

Thanks Dieselwrencher good to know!! I put ARP head studs and good feelpro head gaskets in to hold the heads on. I was planning to run 15psi on the street, then 20psi on the dyno and once and a while on drag strip.

Re: My 52 GMC Build
 

How can I post a video?

Re: My 52 GMC Build
 

Post it to youtube than copy and paste the link in your message.

I put 30psi to a 6.9 at 4200rpm pulling for a summer. :lol: I couldn't blow it up. The next owner though, got it accomplished. Haha

Re: My 52 GMC Build
 

That 6.9L must have pulled hard

Re: My 52 GMC Build
 

Friday I got the axle housing back. Then put it all together and lined it up.
It looks sweet being so short!! Its a Dana 70HD
Attachment 1334359
By Saturday night I had figured out how I was going to be able to build the back frame, so it would work with the suspension and axle. Got the steel cut and tacked then ran out of welding gas :(
Attachment 1334360
Sunday got the frame welded up. Then put truck at ride height about 5". The brackets for the axle in the 4 link kit where for a 3" tube mine is 3.5" so a bit of grinding opened it up. Ready for Monday
Attachment 1334362
Monday got 4 link figured out and welded all but top frame brackets, thats tomorrow. Then air bags:metal:
Attachment 1334363
Attachment 1334364

Re: My 52 GMC Build
 

Nice work, it's really coming together.

Re: My 52 GMC Build
 

Thanks. Ya so happy!!
So today I got upper front brackets on and made and mounted lower air bag plate.
Attachment 1334683
Attachment 1334684

Re: My 52 GMC Build
 

I'm Liking where this build is going ! Keep up the good work !:gmc2:

Re: My 52 GMC Build
 

Not throwing any rocks, but I'm wondering if that 4 link is going to work properly and safely with the upper bars at that angle instead of straight above the bottom ones?

Re: My 52 GMC Build
 

No worries. Its a double triangulated 4 link, its used to keep the axle centered in the frame more. 4X4's use it in extreme. I had to use it due to my limited space and not enough angle left and right. Didn't want a pan hard bar. I talked to the shop that shortened my axle. The only down fall is it increases the height of my roll center. The truck will lean in the corner more but i figured with a 1000 lb motor up front I don' think the back will do much.

Re: My 52 GMC Build
 

Got the air bags mounted today. The truck now can go up and down and roll on 4 wheels umm I mean 6 wheels :bann:
I'll get a vid soon
Attachment 1335106
Attachment 1335107

Re: My 52 GMC Build
 

Looks very nice!

Re: My 52 GMC Build
 

Triangulated 4-links are more forgiving for install and geometry as well. They're fairly popular in hot rods too, not the double triangulated as yours is but just the top bar. Your setup looks good, I am excited to see more of this build.

Re: My 52 GMC Build
 

What a cool build. I own an AD and a '94 factory turbo IDI crew cab dually. My F-350 has a 90cc injection pump, BB code injectors, waste gate adjusted for 15psi(on the stock head bolts and 216,000 mile head gaskets), Hypermax cowl induction with a K&N air filter, Banks down pipe/EGT+boost gauges and 4" straight pipe side exhaust.

What turbo is that?
What other mods got done to the E4OD?
Whats plans do you have for fueling?
A cam swap would be real easy right now.....google R&D IDI Performance.

Re: My 52 GMC Build
 

Got the frame and axle painted. Starting to look like a truck :)
Attachment 1337735
Thanks Wide load c-30. Its a HX35 from a cummins. I found its a good size for what I'm doing. I'm running 3" mandrel bent sst out the side. I have an electric 35 gph fuel pump. Other than that I'm just turning up the lift pump. For the trans I put in a Transgo tugger kit. It was rebuilt about a year before I got it. I'm also using a US Shift Quick 1 controller that allows me to control anything the trans can do. Its going to be manual shift auto. I've looked into a cam but I want to see what the stock set up will give me first. My goal is 300hp and 500lb-ft if I get close to that I'll be happy, but who knows down the road I may do a full motor build.

Re: My 52 GMC Build
 

Amazingly my steering shaft missed the motor without any major mods. I moved the end if steering column over to the drivers door 1.5" and am going to center the column between the gauges.
Attachment 1339664

Re: My 52 GMC Build
 

Finally got a vid put together, showing what I have done so far and motor running. Enjoy
http://youtu.be/N0C3SOCJPCA

Re: My 52 GMC Build
 

very nice work so far -- it should be a awsome ride when done !

Re: My 52 GMC Build
 

Great work! The engine really sounds nice and it looks way easier to work on than any other turbo'd IDI! :lol:

Re: My 52 GMC Build
 

I like it if I had the money I would go diesel as well

Re: My 52 GMC Build
 

Got steering column mounted just before Christmas.
Attachment 1345467
Attachment 1345468
Working on putting the lower cowl back on and then on to fenders, but its slow going right now really cold here 10F feels like -6F not much heat in garage. A bit warmer next week.

Re: My 52 GMC Build
 

I wanted to do something different!! Got a really good deal on the whole drivetrain, could not say no.

Re: My 52 GMC Build
 

Well got the one cowl tacked on. Then got the fender modified. I cut 3" off the bottom because I'm rising the running boards and first test fit. WOW haven't seen the fender in it in about 8 years.
Attachment 1349017
Attachment 1349018
Attachment 1349019

Re: My 52 GMC Build
 

Cool build!!

Re: My 52 GMC Build
 

Dope