The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1967 - 1972 Chevrolet & GMC Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=3)
-   -   What did you do to your truck today.The 3rd chapter (https://67-72chevytrucks.com/vboard/showthread.php?t=773345)

Liz 10-15-2018 12:34 PM

What did you do to your truck today.The 3rd chapter
 
Chapter 2 is now complete, bring on 3. What did you do to your truck today?

tdangle 10-15-2018 01:47 PM

Re: What did you do to your truck today.The 3rd chapter
 
Fixed my strange temp gauge readings. I had replaced the gauge sender unit and had all sorts of strange things going on. It would peg the gauge on warmup until the thermostat opened then read mid scale which was higher then before. Driving it the readings would vary all over the place. Engine was running normal as I was checking it with a thermo gun. Ended up taking the thermostat out, drilled 2 1/8" holes in it and then filling the engine with coolant at the manifold prior to reinstalling the thermostat. Works great now. Only thing I can figure is that I had some sort of air pocket that refused to work itself out.

beaterku 10-15-2018 02:16 PM

Re: What did you do to your truck today.The 3rd chapter
 
4 Attachment(s)
I finally sat down and starting cleaning some of the LS parts. The intake, front and rear covers were disgusting. The inside of the valve covers as well as valley covers where pretty bad too. I gave the trans the ole wire brush treatment and consolidated all of the parts in the bed.

Indychus 10-15-2018 02:30 PM

Re: What did you do to your truck today.The 3rd chapter
 
5 Attachment(s)
I rolled it outside for the first time in 8 years and then test fit my headers!

leddzepp 10-15-2018 02:31 PM

Re: What did you do to your truck today.The 3rd chapter
 
I drank beer and stared at it, that’s about it :lol:

nlped 10-15-2018 04:06 PM

Re: What did you do to your truck today.The 3rd chapter
 
3 Attachment(s)
^^^I had a few beers too... But I did have a chance to clean up the TH400 out of Chubby. It's next to be sold.

Colt_1911 10-15-2018 06:42 PM

Re: What did you do to your truck today.The 3rd chapter
 
4 Attachment(s)
New grill and filler caps on my 71
I had to do some modifying do to the AC, but turn out pretty sweet

samkost 10-15-2018 06:49 PM

Re: What did you do to your truck today.The 3rd chapter
 
Very nice Colt, :metal:
If I may ask, what product/vendor are the fillers and particularly the filler cap over the top of the radiator?
Thanks,
Sam

FRCvette 10-15-2018 06:57 PM

Re: What did you do to your truck today.The 3rd chapter
 
Very nice job on cutting filler panel for a c. I am also interested in radiator cover.

Colt_1911 10-15-2018 07:10 PM

Re: What did you do to your truck today.The 3rd chapter
 
LMC Truck for both in the black finish

samkost 10-15-2018 07:54 PM

Re: What did you do to your truck today.The 3rd chapter
 
Thanks Colt, :clap:
Sam

OregonNed 10-15-2018 08:41 PM

Re: What did you do to your truck today.The 3rd chapter
 
Making plans to go refuel it..

CG 10-15-2018 09:08 PM

Re: What did you do to your truck today.The 3rd chapter
 
1 Attachment(s)
Last week I moved it from beside the shop to the front of the houses driveway and cleaned all the leaves of of it. Then I cleaned out my shop enough to get it inside. Then we had a bit of a freeze so last night I put my daily in the shop and tonight I put the GMC back beside the shop to get covered with leaves and gunk again. Poor thing .

NoStopN 10-19-2018 07:17 PM

Re: What did you do to your truck today.The 3rd chapter
 
It got a shout out on Twitter by GMC. https://twitter.com/GMC/status/1053304723057635330

Domingo 10-19-2018 07:51 PM

Re: What did you do to your truck today.The 3rd chapter
 
Drank beer and replaced front wheel Bearings

Canuckvetter 10-19-2018 08:30 PM

Re: What did you do to your truck today.The 3rd chapter
 
1 Attachment(s)
I added the, new to this truck, door panels, deluxe knobs and deluxe glovebox door. Slowly building a patina CST. Thanks 1rippen6 for the armrests.


http://67-72chevytrucks.com/vboard/a...1&d=1539995052

70STOVEBOLT 10-20-2018 10:19 AM

Re: What did you do to your truck today.The 3rd chapter
 
2 Attachment(s)
Removed the doghouse and pulled the motor and trans to clean up the front third of the frame for paint.

3757chevy 10-20-2018 05:36 PM

Re: What did you do to your truck today.The 3rd chapter
 
2 Attachment(s)
Drove to work this afternoon.;) I had driven my Blazer this morning.:mm:

RodnRudy 10-20-2018 06:25 PM

Re: What did you do to your truck today.The 3rd chapter
 
5 Attachment(s)
I "winterized" Old Red today. Replaced the "mags" with the ralleys and while I had the rear wheels off I replaced the brake shoes and painted the new drums I bought at Auto Zone. I've never liked the drums I got at NAPA, they were not concentric, and causing a pesky vibration. I'll finish buttoning her up tomorrow after the paint on the drums is dry and take her for a test drive.

Andy4639 10-20-2018 08:28 PM

Re: What did you do to your truck today.The 3rd chapter
 
3 Attachment(s)
I traded some old 4 lug pony car wheels and tires for these to go on the front of my ramp truck. The guy said he bought them in 1970 and has had them on several trucks.
They aren't perfect but they are perfect for the ramp truck! :metal: :lol:
:chevy:

tommy3horse 10-20-2018 11:27 PM

Re: What did you do to your truck today.The 3rd chapter
 
Took my 17yr old out for a cruise around town. JJDa Boss and his his gang are here and all the po-po are there. I think i surprised the boy by laying rubber and making a lil too much noise...in the middle of town, sounded great.
Tom

Steeveedee 10-22-2018 09:59 PM

Re: What did you do to your truck today.The 3rd chapter
 
Put the new Cold Case radiator in. I've had heating problems with the 4-row brass radiator, even after flushing the snot out of it. I put the thing in and couldn't get the lower trans cooler line fitting installed to save my life. Took it back out and realized that the threads on those internal fittings were scrofulous. Brushed all the crud out, put the thing back in and the fittings threaded right in. Finished up, and went to buy a new burp bottle. Once I get it all sealed up, I'll drive it and make sure there are no leaks. Then...put in new coolant. Replaced the old heater control valve while I was at it. My FiL had installed shutoff valves like you see under the sink in one of the lines. :confused: I removed it for the flushing process, and was happy to see that the heater core didn't leak. I don't think that it is original. At least I hope not.

Next, I'll be rebuilding the alternator. The front bearing is chuckling, and I don't know if it has ever been rebuilt.

ETA- Took the truck to a steep hill and ran it up to 75 MPH. It's only 78º out, but the gauge stayed right at 190º, which is what the thermostat is rated at. Shut it off, let the temp climb while I was in buying Lottery tickets. Fired it up and it dropped right back down to 190º within a block. Problem fixed. Of course, this doesn't prove it will run cooler when towing the trailer in 100º weather. This truck always ran hot even with a new 4-row brass radiator. Anyone want to buy a used 4-row brass radiator cheap? :D

RodnRudy 10-27-2018 03:47 PM

Re: What did you do to your truck today.The 3rd chapter
 
2 Attachment(s)
I replaced the drivers side valve cover gasket. It was leaking at the bottom rear and the oil tracked down to the flex plate cover and dripped on the floor. I used Fel Pro gasket and Permatex Ultra Gray sealer. Hope this did the trick, I'll know tomorrow when I test drive her.

NoStopN 10-28-2018 06:32 PM

Re: What did you do to your truck today.The 3rd chapter
 
I planned to put the tail lights & reverse light in my donor bed, but I realized that I didn't have the screws needed to hold them to the bed. Does anyone know the thread pitch of screws that I'll need? :D

With the first item on hold, I moved back to the last unfinished step. I got the bed lined up & bolted down, followed by the bed side to floor bolts that I could get in. Surprisingly, only 1 had to be left out. So, at least the bed won't rattle or fly off. But there won't be enough speed to make that happen if I don't have brake lights, turn signals, etc. Today was still progress, so it's all good.

yuccales 10-28-2018 06:53 PM

Re: What did you do to your truck today.The 3rd chapter
 
Dump trip this morning. Wash and vacuum, tire rotate afterwards.

CarolinaHD 10-28-2018 07:35 PM

Re: What did you do to your truck today.The 3rd chapter
 
1 Attachment(s)
Got the 67 running and moving! Ran it up and down the driveway a few times and it should make the 10 mile trip to the new house this week.

Slid the rear axle under the 06 to move onto the trailer

Oil change and tire rotation for the Tahoe

Steeveedee 10-28-2018 08:02 PM

Re: What did you do to your truck today.The 3rd chapter
 
Pulled the alternator because the front bearing is noisy. It's been on there for a donkey's years. I couldn't get the rotor out of the front bearing. I'll just get a rebuilt one tomorrow. Turns out that it isn't the original, anyway. I wanted to rebuild it, they're easy (if you can get them apart).

jocko 10-28-2018 08:03 PM

Re: What did you do to your truck today.The 3rd chapter
 
Quote:

Originally Posted by RodnRudy (Post 8368421)
I "winterized" Old Red today. Replaced the "mags" with the ralleys and while I had the rear wheels off I replaced the brake shoes and painted the new drums I bought at Auto Zone. I've never liked the drums I got at NAPA, they were not concentric, and causing a pesky vibration. I'll finish buttoning her up tomorrow after the paint on the drums is dry and take her for a test drive.

Phil, what did you paint your drums with? When I looked at the inside of the drums, I thought the blue tape was a reflection off of "highly polished" braking surfaces... Ha. Truck looks sharp!

66clow 10-29-2018 06:57 PM

Re: What did you do to your truck today.The 3rd chapter
 
4 Attachment(s)
Close to having it in one color. And plan to do it in red and white like this one. But my color choices changes day to day.

elorenzof 11-01-2018 02:53 PM

Re: What did you do to your truck today.The 3rd chapter
 
2 Attachment(s)
This past weekend I took of the Engine Crossmember and Installed a new freshly coated Crossmember, Upper and Lower Control Arms, New Steering Stuff ie: tie rods, pitman arm, etc... New Drop Spindles with Disc Brake Conversion kit.

OregonNed 11-01-2018 03:44 PM

Re: What did you do to your truck today.The 3rd chapter
 
1 Attachment(s)
One of my side terminal bolts stripped the battery threads, so I moved wiring up to the top posts with new clamps. In the end, I moved the main cables over to the next smallest set screw opening for a better fit.

FRCvette 11-01-2018 04:42 PM

Re: What did you do to your truck today.The 3rd chapter
 
Just finished changing oil on my 70. I am ready to drive again as soon as rain stops.

morepwr 11-01-2018 05:06 PM

Re: What did you do to your truck today.The 3rd chapter
 
You guys are making me look bad! All I did was drive it to work today!

samkost 11-01-2018 05:14 PM

Re: What did you do to your truck today.The 3rd chapter
 
Quote:

Originally Posted by OregonNed (Post 8375913)
One of my side terminal bolts stripped the battery threads, so I moved wiring up to the top posts with new clamps. In the end, I moved the main cables over to the next smallest set screw opening for a better fit.

OregonNed,
Those are sharp.
I know they aren't OE but I really might have to get a pair of those top post Battery Terminals.:metal:
Thanks,
Sam:chevy:

elorenzof 11-01-2018 06:13 PM

Re: What did you do to your truck today.The 3rd chapter
 
Quote:

Originally Posted by Indychus (Post 8364965)
I rolled it outside for the first time in 8 years and then test fit my headers!

WOW. Just. WOW.

dflarsen77 11-03-2018 04:00 AM

Re: What did you do to your truck today.The 3rd chapter
 
Slowly blasting and epoxy on the body pieces! Hoping to get it in paint by the end of the month!

70STOVEBOLT 11-03-2018 04:02 PM

Re: What did you do to your truck today.The 3rd chapter
 
Removed the right side spindle and drum assembly to make way for the disc brake swap.

elorenzof 11-03-2018 07:34 PM

Re: What did you do to your truck today.The 3rd chapter
 
Quote:

Originally Posted by 70STOVEBOLT (Post 8377059)
Removed the right side spindle and drum assembly to make way for the disc brake swap.

I just did that job it went pretty well. What product did you choose to go with?

kcmarkd 11-03-2018 09:33 PM

Re: What did you do to your truck today.The 3rd chapter
 
Today I replaced points, condenser, rotor, and cap. Set dwell angle and timing, then minor carb adjustments. And, even cooler, took it out on a short shake down cruise to the store to verify tuning and recent brake work. Didn't blow up, didn't crash, didn't die on the side of the road, and made it back home!

Oh, and drank a beer or several.

tdangle 11-03-2018 11:54 PM

Re: What did you do to your truck today.The 3rd chapter
 
Replaced the passenger side vent rubber. Went way faster than the drivers side last week. I guess practice makes perfect


All times are GMT -4. The time now is 07:31 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com