DBW Gas Pedal Adpater bracket for truck/suv pedal
 

After receiving many of requests for pedal bracket that will work with the 03-07 truck pedal, I fabricated this pedal bracket. This is a bolt in bracket that uses the 03-07 truck/SUV DBW pedal (may fit others) for the 67-72 LS conversions. Let me know if you have any questions or suggestions.


*****
GEN IV flat brackets for the 05+ Corvette Pedal can be found here: http://67-72chevytrucks.com/vboard/s...d.php?t=631165
*****


**** PEDAL MOUNT INSTALL INSTRUCTIONS ****

1. Start by bolting your truck/SUV DBW pedal assembly to the mount bracket using the provided 3/4" 1/4-20 bolt. Do not tighten.

2. Next, loosely bolt the mount bracket to the firewall using the three nutserts in the firewall where the original pedal was mounted. You can do this by aligning the three pre-drilled holes on the right side of the mount bracket. Use three 3/4" 1/4-20 bolts to attach to the firewall that were included in your kit.

3. Next, align the left edge of the mount bracket with the raised vertical firewall brace. There are two pre-drilled holes on the top and bottom on the left edge that will be used as a guide to install the provided self-tapping bolts.

4. After you attach the left side of the mount bracket to the raised brace, you can tighten the three bolts on the right side of the bracket using a 7/16 socket.

5. When the pedal bracket is securely attached, you can adjust the pedal position as desired by moving the top of the DWB pedal assembly left or right. If necessary, there is also about 1/2" up or down adjustment from the slotted hole in the bottom of the DBW pedal assembly.

6. After you have the pedal in the position that you like, use a 7/16 socket to tighten the bottom bolt holding the DBW pedal assembly.

7. Next, you should actuate the pedal up and down to check for any interference in the movement. There shouldn't be any, but all the trucks are a little different so be sure to check. If there is any interference, loosen the bolt and adjust as necessary.

8. Once the DBW pedal assembly is adjusted, make sure the bottom bolt is tight and remove the mounting bracket and DBW pedal assembly from the firewall as one piece. This will hold the pedal in your desired position and allow you to drill the top hole to finish mounting the pedal assembly.

9. Next, mark the top pedal assembly hole using the DBW pedal assembly as a guide. Remove pedal assembly and then drill a 1/4" hole where previously marked. Re-install the pedal assembly with the provided 1/4" bolt and nut and tighten. This nut should be tacked in place, just like the one on the bottom, so that the DBW pedal assembly can be removed by itself without removing the entire pedal mount bracket.

NOTE: If you don't have a welder, you can just tighten the top bolt and leave the DBW pedal on the bracket for reassembly.

If you have any questions or suggestion about the installation, please let me know. Thanks for your purchase!

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

bump

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

3 brackets sold. 9 left.

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

5 brackets sold. 7 left.

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

6 brackets sold, 6 left.

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

**** INSTALL INSTRUCTIONS ****

Pedal mount instructions:


1. Start by bolting your truck/SUV DBW pedal assembly to the mount bracket using the provided 3/4" 1/4-20 bolt. Do not tighten.

2. Next, loosely bolt the mount bracket to the firewall using the three nutserts in the firewall where the original pedal was mounted. You can do this by aligning the three pre-drilled holes on the right side of the mount bracket. Use three 3/4" 1/4-20 bolts to attach to the firewall that were included in your kit.

3. Next, align the left edge of the mount bracket with the raised vertical firewall brace. There are two pre-drilled holes on the top and bottom on the left edge that will be used as a guide to install the provided self-tapping bolts.

4. After you attach the left side of the mount bracket to the raised brace, you can tighten the three bolts on the right side of the bracket using a 7/16 socket.

5. When the pedal bracket is securely attached, you can adjust the pedal position as desired by moving the top of the DWB pedal assembly left or right. If necessary, there is also about 1/2" up or down adjustment from the slotted hole in the bottom of the DBW pedal assembly.

6. After you have the pedal in the position that you like, use a 7/16 socket to tighten the bottom bolt holding the DBW pedal assembly.

7. Next, you should actuate the pedal up and down to check for any interference in the movement. There shouldn't be any, but all the trucks are a little different so be sure to check. If there is any interference, loosen the bolt and adjust as necessary.

8. Once the DBW pedal assembly is adjusted, make sure the bottom bolt is tight and remove the mounting bracket and DBW pedal assembly from the firewall as one piece. This will hold the pedal in your desired position and allow you to drill the top hole to finish mounting the pedal assembly.

9. Next, mark the top pedal assembly hole using the DBW pedal assembly as a guide. Remove pedal assembly and then drill a 1/4" hole where previously marked. Re-install the pedal assembly with the provided 1/4" bolt and nut and tighten. This nut should be tacked in place, just like the one on the bottom, so that the DBW pedal assembly can be removed by itself without removing the entire pedal mount bracket.

NOTE: If you don't have a welder, you can just tighten the top bolt and leave the DBW pedal on the bracket for reassembly.

If you have any questions or suggestion about the installation, please let me know. Thanks for your purchase!

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

I want one

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

Sweet! PayPal information is in the first post of the thread. Let me know so I can ship it today.

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

I want one Rob!

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

Shipped. THANKS!

Do u still want one?

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

Sorry, I forgot about it, but just sent paypal

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

No worries! It shipped yesterday. Thanks again.

R

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

Bump for a great seller. The bracket installed easily and is a great time saver.

http://i96.photobucket.com/albums/l1...1/IMG_0025.jpg

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

hi I was wondering if you have any brackets left?

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

Yes I do! The price is 100.00, Paypal is robhartley@aol.com. Thanks!


Thanks Jonathan!

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

Just got your PM, I'll take one well!

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

Thanks!

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

PayPal sent!

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

Hey man will this work on a 2009 pedal?

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

Thanks! Will be shipped tomorrow.

Please post a picture of the pedal.

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

I want one too.

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

Payment sent. Thanks

Re: Gas Pedal Adpater bracket for truck/suv pedal
 

Will try to get it shipped out tomorrow. Thanks!

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Payment sent, Thanks

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Thanks! Will be Monday before I get the next batch and get it shipped.

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Any plans for making these for a 60-66?

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Not yet. I'm not sure what the demand would be. I think one guy used one of the current brackets and modified it slightly.

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

ok thanks

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Got a new batch of the pedal brackets!!!

***10 Jan 2015 UPDATE: All new purchases will now include: USPS shipping in CONUS, paypal fees and all the necessary hardware to install the pedal bracket for only $100. Hopefully this will make payment and installation a little easier.

Paypal is robhartley@aol.com. ***

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Got mine the other day! Super fast shipping and a top notch piece too! Thanks!

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Thanks! Glad you like it. Post pictures when you get it installed.

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Thanks Rob quality product.

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

very nice. i'll see if you still have any within a month or 2...got other things to spend money on to get the swap done still :) looks good tho sir!

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Hey rob I'm going to need one of these brackets after my recent purchase. I have a 2005 Escalade pedal, this bracket will work right?

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Yes, it should be the same as the one pictured above.

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Thanks Rob yeah it looks to be the same, payment sent for bracket.

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Thanks Keith! It will ship out via USPS today. Let me know when it arrives.

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

No worries. I've got 5 more boxed up and read to ship. Just let me know.

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

I got the pedal bracket in Friday Rob, nice piece and fast shipping, thanks.

Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
 

Thanks Keith!