![]() |
The Snortin' bull
2 Attachment(s)
1960 gmc swb.build.The day it was brought home as found.Rust is minimal.An abandonded project.
|
Re: The Snortin' bull
1 Attachment(s)
in the driveway first day.
|
Re: The Snortin' bull
Welcome to the forum :D
That does look like a solid truck to work with. Looks like it needs a little 'pick me up' What are your plans for it? |
Re: The Snortin' bull
:hi: and Welcome Aboard! :mm:
Diggin' the all around look...:metal: Plans and Pics needed...;) |
Re: The Snortin' bull
The frame has been modded,Extreme kick up on triangulated 4 bar in rear on air with dana 44.Front frame also modded with updated frt suspension using 1987 c10 .on fullbagged suspension frt and rear using some Porterbuilt products.Thanks for asking .
|
Re: The Snortin' bull
Welcome aboard! Don't go over a speed bump! :lol: Like the project. :chevy:
|
Re: The Snortin' bull
Welcome aboard, looks like fun
|
Re: The Snortin' bull
2 Attachment(s)
Thanks for the welcome.
|
Re: The Snortin' bull
2 Attachment(s)
60 gmc in build progress.tear down inspect and update.
|
Re: The Snortin' bull
love those gmc hoods. looks like a sweet project
|
Re: The Snortin' bull
3 Attachment(s)
So in May 2014 this basket case GMC I brought home.Each day it could be 5 minute's or 5 hour's I try to do something to keep the project moving.
|
Re: The Snortin' bull
2 Attachment(s)
The auto manufacture's keep part's very similar over the year's .To transfer in updated frt suspension into these truck's is not a huge problem.The gauge of metal in the newer crossmember and a arms is heavier also.
|
Re: The Snortin' bull
1 Attachment(s)
Been a new year with a handfull of things going on, Though trying to find time to keep on the project.posting a few minor things . Minor small jobs. A trick for harness wiring if supported and protected well,Block plates for heater installed a mojave small inside unit.Picked up a genie radio block off.finished steering and suspension front updating.
|
Re: The Snortin' bull
1 Attachment(s)
Jan 2015
|
Re: The Snortin' bull
1 Attachment(s)
Radio delete
|
Re: The Snortin' bull
1 Attachment(s)
A mix from orig gm,Later model c-10 and Porterbuilt product's. One note about Porterbuilt 'top quality' . Though are tough to get on the phone.
|
Re: The Snortin' bull
1 Attachment(s)
Slowly after probably decades of being dormant life is coming to Gmc.
|
Re: The Snortin' bull
1 Attachment(s)
Installed a full american auto wire harness.
|
Re: The Snortin' bull
Nice Progress! :metal:
|
Re: The Snortin' bull
That thing is on the rockers..where do the rear bag mounts go?
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Nice progress! :chevy:
|
Re: The Snortin' bull
1 Attachment(s)
This was nice to find in the Dana . A loaded posi. No one wheeler peeler here.
|
Re: The Snortin' bull
1 Attachment(s)
This will have to trimmed and bracketed to fit.Transmission mount is a Art Morrison pre made universal piece. For the price you can't beat it. Time is money.
|
Re: The Snortin' bull
1 Attachment(s)
Hinge's cermachromed .Also have latche's done in same coatig for hood. May not use the hinge's in the end they will work now.
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
1 Attachment(s)
Setting the core support .The frame horn's had been modified so have to make sure fitment is set up good.New lamp harness also in. I can see the light.
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
1 Attachment(s)
This is the Snort in the bull. A built 400 small block chev. Fully balanced punched out. 272 Isky.Hyper-t pistons.edurashine Edelbrock eps intake. Gm performance,Stewart water pump, ARP h-ware,ported polished heads. Roller rockers etc.behind it will be a 700r4 trans.
|
Re: The Snortin' bull
1 Attachment(s)
Might be minor thing to some but i can't a quarter panel bed side flappin in the breeze. Extended the struts to the frame.
|
Re: The Snortin' bull
1 Attachment(s)
Due to the past phenobulation of the torsion bar front end from the past owner i had to modify the Porterbuilt shock mount's on the frame to allow full open and collapsed shock travel.
|
Re: The Snortin' bull
nice stance love the GMC grills truck is looking great.
|
Re: The Snortin' bull
Been chipping away here and there on GMC .Life get's hectic.More pic's to come and progress.
|
Re: The Snortin' bull
1 Attachment(s)
Got heater assy. mocked up and plumbed thru a bulkhead fitting plate thru firewall.
|
Re: The Snortin' bull
1 Attachment(s)
bulkhead pass thru engine side.
|
Re: The Snortin' bull
1 Attachment(s)
gusset and fish plated.
|
Re: The Snortin' bull
1 Attachment(s)
Installed a simple water control valve for heater. Cable to original dash control's.
|
All times are GMT -4. The time now is 04:06 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com